Question about 1989 Mazda 323

1 Answer

Electrics prob. with indecators lights and hazerds lights

Direction lights and hazerds lights not switching on making scratching noise when applied prob lem in locking mecisam how can i repair

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Mazda Expert
  • 227 Answers

Check all the bulbs theres probably more than one bulb busted

Posted on Apr 06, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 jeep grand cherokee will not turn over


Constant 12-volt power is applied through 40 A FUSE 8 in the power distribution center (PDC) to the engine starter motor relay and through 40A fuse 14 to the ignition switch. If the park/neutral position switch is connected to ground, turning the ignition switch to START causes 12 volts to pass through 10A fuse 31 in the junction block and the engine starter motor relay coil to close the relay and apply 12 volts to the starter. Any of the parts mentioned could be open or defective.

Apr 01, 2014 | Cars & Trucks

2 Answers

The check engine light stays on after oil change. When you apply the brakes the steering wheel vibrates and there is a weird humming type noise coming from the rear while idling.


Hope the oil filter was changed and with the OE type and the correct oil grade.
If so the oil pressure switch can be clogged and so produce the check engine light.
When applying brakes the steering vibrates as it can be due to faulty linkages in steering column, problem in the hydralics pump or fault in the steering rod bearings.
finally the weird noise from rear can be from a faulty exhaust , leak or poor joint in the exhaust or vibration of the exhaust with loose mountings.

Sep 21, 2011 | 2000 Dodge Grand Caravan

1 Answer

Windshield washer pump not working


Unplug the pump motor located on the side of the fluid resevoir. Apply 12v directly to pump to check operation. If pump makes noise then it is a switch or electrical problem. It nothing happens then replace the pump.

Sep 01, 2011 | 1995 Mercury Cougar

3 Answers

"ABS" indecator light is on


Most common problems are front wheel bearings they are integral to the wheel speed sensors for ABS system. I'd get it scanned to see which side is faulty.

Jan 26, 2011 | 1998 Pontiac Sunfire

1 Answer

1989 chevy k1500 electric passenger window not working


I sounds like it might be a window switch that has gone bad ck the connector at the window motor by connecting a test light across the 2 wires operate both window switches the test light should light If it doesnt then connect the test light to a good ground and back prob the connector on either wire and operate the switch in both directions the test light should light In one position of the switch then ck the other wire the same way and the test light should light up with the switch in the other position (down up) wich ever wire the test light does not light up on needs to be cked for a break. The wires in the the door pass through (the rubber boot that goes from the door to the body ) can break pull the boot loose and pull the wiring out as far as possible to ck for broken wires.

Mar 08, 2010 | 1990 Chevrolet K1500

2 Answers

2001 chevy blazer all lights work except the brake lights. The third top light works but not the bottom. Bulbs are good and no fuses are out.


does the 4 ways work? if they do it would be the brake light switch at the brake peddle,,,,,,,,, if they dont the problem is in that red hazerd switch on your steering colum inside it has 3 spring loaded pads that make 3 electrical contacts each so 9 in all and they get sticky from dirt, dust & coffee and hot chocolite dumped on them and stick and burn out. and your brake lights stop working... I could tell you how to fix it but rather diagnose what it is first

Jun 11, 2009 | 2001 Chevrolet Blazer

1 Answer

Noise when stepping on brakes


they prob just looked at the outter pads ,the inter pads will ware out first thats where the pressure is applied , you need too pull the callipaliars too check them!!

Apr 20, 2009 | 2006 Chevrolet HHR

1 Answer

No brake lights


check hazard fuse or make sure the hazerd switch is dis engadged. mine was the same problem just cant use the hazard

Apr 03, 2009 | 1984 Dodge Ramcharger

1 Answer

The hazerd switch clicks all the time


you need to replace it.... shouldn't have trouble finding it... just follow the noise

Mar 18, 2009 | 2001 Oldsmobile Alero

2 Answers

Brake light


check all fuses some vehicls now a days have seperate fuses for left and right sides

Feb 09, 2009 | 2000 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...