Question about 1994 Honda Civic
I need to know what cars will a 1994 Honda Civic EX fit into?
There are repair shop manuals that will tell you that, but by far the easiest way to find out, is to call your local wrecking yard or U-pull it type place. They can tell you if they wanted to.
Posted on Mar 29, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1998 honda civic ex sedan
remove rear seat, remove round metal cover, disconnect fuel lines and wires from top of fuel pump, jack up rear of car. remove gas tank straps, lower gas tank with a jack, install is reverse.....if you need to just replace the fuel pump you don't have to remove tank you Can access from under rear seat good luck and please rate -jeff
Posted on Sep 05, 2008
SOURCE: 1994 honda civic ex
IF YOU HAVE ANY FREIND OR NOW ANYBODY WHO WORKS AT AN AUTO REPAIR SHOP 9 TIMES OUT OF 10 THEY HAVE ACCESS TO ONLINE AND CAN GO ON AND PRINT IT OUT FOR YOU OTHER THAN THAT YOU NEED TO BUY A BOOK FOR THE VEHICLE CHILTONS OR SUCH
Posted on Dec 04, 2008
make sure they are tight
could be time for head gaskets
make sure the old gasket from the old filter came off the block sometimes they come off old filter and stick this causes a leak due to improper seal.
Posted on Apr 10, 2009
Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.
IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)
When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...
Posted on May 23, 2009
Tips for a great answer:
Dec 16, 2014 | 1994 Honda Civic
Jan 09, 2014 | 1994 Honda Civic
Oct 21, 2010 | 1994 Honda Civic
Jun 20, 2010 | 1994 Honda Civic
May 30, 2010 | 1994 Honda Civic
Mar 13, 2010 | 1994 Honda Civic
Jan 01, 2010 | 1994 Honda Accord
Apr 04, 2009 | 1994 Honda Civic
Mar 31, 2009 | 1994 Honda Civic
128 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: