Question about 1993 Jeep Grand Cherokee

1 Answer

Serpintine belt how to tighten belt

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 400 Answers

Youtube has a video showing how to replace the belt.
http://www.youtube.com/watch?v=2-Oc1_ToRbk

Posted on Mar 29, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get corret tension on drive belt after fitting


most have a self tensioner on serpintine belts if it is a v belt pry on alternator while tightening and have 3/8 inch play up and down on the belt

Nov 11, 2015 | Cars & Trucks

1 Answer

How to tighten fan belt on 1999 fairmount ghia v8


The cars today do not have belt adjustments they have what is caller a idler pulls that keeps a serpintine belt "all in one belt" that snakes around all the pulleys,thus the serpintine..name..anyway if it is slipping most likely the belt needs replacing or the idler itself is bad..neither can be adjusted..the fix is replacement...your car should have a belt route under the hood showing where it goes and the idler is spring loaded and easy easy to take the pressure off to take the old belt off and replace it..not a big job for garages if you wish not to DIY .good lucK

Oct 01, 2014 | Cars & Trucks

1 Answer

Replacing serpintine belt, belt keeps slipping off, How can you fix? 1999 pontiac grand am


Sounds like the belt tightener unit is wore out and needs replacing.
As the bearings wear out the pulley will move around causing the belt to come off. When you replace the tightener you should replace the belt as well.

Jun 23, 2014 | 1991 Oldsmobile Cutlass Ciera

1 Answer

2014 Ram Cargo van - tighten serpintine belt?


you don't ...if the belt is loose you need to replace the tensioner

May 07, 2014 | 2014 RAM CV Tradesman

1 Answer

How to tighten serpiontine belt


http://www.youtube.com/watch?v=2-Oc1_ToRbk

Mar 28, 2014 | 1997 Jeep Grand Cherokee

1 Answer

CHANGING SERPINTINE BELT "98 WANGLER


Somewhere in the world there may be a specification for that but in reality, just make the pulley through bolt tight (without being and animal on it). The long jack bolt gets tightened first. There, you check belt deflection. You should have about one inch or slightly less deflection in the center of the longest run of the belt. After getting it to that point, lock it and tighten the pulley. Run it for a few minutes and then drive it. If the belt squeals, loosen the adjustment and give it a few more turns. Do not over-tighten it. A loose belt will be noisy. An overtightened one can destroy component bearings.

May 19, 2011 | 1998 Jeep Wrangler

1 Answer

How do i tighten a surpentine belt?


All serpintine belts tighten when the belt tensioner is released.

Jan 09, 2011 | 2005 Chevrolet Aveo

1 Answer

2000 WINDSTAR VAN SERPINTINE BELT TIGHTENING


the belt is tensioned by an automatic belt tensioner pulley assembly, so what is the problem with the tension? belt noise?

Jun 09, 2009 | 2001 Nissan Sentra

1 Answer

Replace serpintine belt


You shouldn't need to most of the time all you need is a 15mm wrench. Use it by turning the spring tightener inward toward the center of the motor than the belt should come off. Also when you take it off make sure you know how the belt goes around the pulleys so everything will work together like normal. when putting the belt on you should use the wrench to turn the tightener back inward and slip the belt back on and make sure it looks just like the old one when its on.

Jan 12, 2009 | 2003 Toyota Corolla

1 Answer

Nebettleed to change serpintine belt on a 2000 voltswagen


The easiest solution I can say would be to go to parts america or Advance Auto Parts during a non peak time and ask for help. These belts should be a 5 minute replacement and most store employees will enjoy offering you the free service just to get out of the store for a few minutes. SOME stores are more willing to help than others.

(If you over tighten the belt you will have problems and if you under tighten the belt you will have squeals. If you still wish to do this yourself just make sure the belt is tight enough that it only turns 90 degrees in the middle to the left of right when tightened.)

Aug 17, 2008 | 2000 Volkswagen Beetle

Not finding what you are looking for?
1993 Jeep Grand Cherokee Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...