Question about 2005 GMC Yukon Denali

Open Question

Location of efs module

Obd code b0101

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Quad driver module code 26 and 28


A quad driver is a transistor in the engine control module ! GM OBD Trouble Code 26 GM OBD Trouble Code 28

Jul 24, 2016 | Cars & Trucks

1 Answer

How do I fix airbags with codes b0101 and b1181


posible you need a new clock spring under the stering wheel the codes you get say the circuit on the driver side squib

Sep 17, 2014 | 2007 Toyota Sienna

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

Location of obd module in a 2001 oldmobile silhouette minivan


parts store can tell you as can dealer service..most behind the passenger kick panel inside the door..

Dec 20, 2013 | 1995 Mercury Villager

1 Answer

WHAT IS THE PROBLUM WITH AIR BAG CODE B0101


Try moving the driver's seat back and forth and see if the light will go off. If so the wiring under the seat could be loose and or broken.

Jan 03, 2013 | Cars & Trucks

1 Answer

Toyota camry B0101 code


DTC B0101/14 is recorded when an open is detected in the D squib circuit. Basically this means that there is a problem with the air bag or clock spring in the steering wheel. This needs to be serviced by a dealer.

Oct 14, 2012 | 2001 Toyota Camry

1 Answer

How to check circuit 1998 nissan frontier fuel tank tempertur sensor


I assume you mean "P0180" not "p180", which is not a valid OBD Diagnostic Test Code.

So you replaced the fuel pump module without even diagnosing this code??? WOW! That was an EXPENSIVE mistake!

You pretty much answered your own question. The wires are located between the fuel pump module (Tank Fuel Temperature "TFT" sensor), the PCM and the ground point for the sensor.

Connector pins "T" and "E" at the fuel pump module connector are the wires for the TFT sensor

May 11, 2012 | 1998 Nissan Frontier

1 Answer

95 grand am codes 34,27,55,19


Are you sure about your reading, Code 19 isn't listed.

DTC OBD I Code 34
Description: Speed control solenoid(s) circuit is open or shorted
Notes: For vehicles equipped with speed control

Possible Causes
- Bad connection or wiring - Check the wiring and connections between the logic module and the solenoid. Clean and regrease any corroded connectors with dielectric grease and repair any shorts.
- Bad solenoid(s) - The speed control is located near the battery and will have to be disassembled.


DTC OBD I Code 27
Description: Injector driver circuit 2 open or shorted

Possible Causes
- Bad connection or wiring - Check the wiring and connections to injectors 3 and 4 in the injector harness (above the fuel rail) and between the harness and the power module (or SMEC) and the injector contol lines between the logic module and power module. Clean and regrease any corroded connectors with dielectric grease and repair any shorts.
- Injector driver transistor failure - Check the injector signals coming from the power module (or SMEC). They should rise to about 12V when the injector is off and drop close to 0V when the injector is on. If they are out of spec, you may need to replace the power module.


DTC OBD I Code 55
Description: End of message

Possible Causes
No further fault codes are stored. If this is the only code received, then there are no codes stored in memory. This code will always be given, even if nothing is wrong. If you do not get this code, then you may not be retreiving the codes properly, or the power loss light may be burnt out. The light should come on for 1 second when the ignition is initally turned on as a bulb test.


I hope this helps; remember to rating this and just keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment.

Have a nice day and thanks for using FixYa.
Jose.

Oct 17, 2011 | 1995 Jeep Grand Cherokee

1 Answer

WHAT IS DTC-01 P0673 ON A 2500 HD


OBD Code P0673refers to
The Engine Control Module (ECM) has detected a fault in the cylinder #3 glow plug circuit SymptomsPossible sumptoms of OBD code P0673
- Engine Light ON (or Service Engine Soon Warning Light) - Lack/Loss of Power - The engine may be harder to start - Engine hesitation CausesPossible causes of OBD code P0673
- Cylinder #3 glow plug circuit is open or shorted - Faulty cylinder #3 glow plug - Faulty glow plug module

Jul 09, 2011 | GMC Sierra 2500HD Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...