Question about 2007 Lincoln MKZ

Open Question

I have a 2007 lincon MKZ and i have ABS code B1676 Battery Pack voltage out of range

Code b1676 battery pack out of range. car was stolen and ac stoped working and this is the only code

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1011 Answers

SOURCE: I'm trying to replace battery in 2007 lincoln mkz.

try a twist on it with a vise grips

Posted on May 05, 2010

Ad

SOURCE: how to bleed brakes for a 98 lincon town car with

Same as you always have, with any vehicle,engine running,ABS no issue

Posted on Oct 15, 2010

wrenchjockey
  • 75 Answers

SOURCE: how much oil does my

5.5 quarts

Posted on Oct 19, 2010

  • 7353 Answers

SOURCE: what battery should I put

I would get a BXT96R Motorcraft battery. Keep your Ford all Ford, plus it has a 36 month free replacement warranty.

Posted on Dec 21, 2010

  • 1 Answer

SOURCE: Where keypad entry code located on 2007 Lincoln

found a 5 digit number under bar code behind glove compartment.could this be the keypad entry code to
2007 mkz.dino

Posted on Jan 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alternator went out, truck died, Towed on hauler. Replaced alternator and now gages go crazy Codes are B1676, C1226, P0460 and P1000 I read if its driven the syst1em will reset itself. Is this true?


If the battery voltage is low it will set codes that are not prudent. It is not a good idea to charge a dead battery with the alternator as it causes the alternator to run at high amperage.Charge the battery, clear codes and retry

Apr 11, 2015 | Ford F-150 Cars & Trucks

2 Answers

2000 ford expedition I changed plugs pcv egr valve cover gasket I am still getting power loss and hesitation in drive and sometimes it stalls plus I have a b1676 code


There is no B1676 DTC. You probably mean P1676 which refers to incompatible injector data. Probable causes are:
1. Control unit software needs updating
2. Faulty PCM or ECM

Checking these two probable causes may get performance back to normal.

Jan 16, 2014 | Cars & Trucks

1 Answer

I have a 2000 ford expedition it is gasping for air it stalls and has a b1676 code


check vacuum leaks such as hydro box linkage host.. the code is ABS lamp and Break Lamp problems

Jan 16, 2014 | Cars & Trucks

1 Answer

B1676 - how do you reset this code?


check connections and look for a failed fuseable link wire..

Dec 27, 2013 | 2004 Mercury Sable

1 Answer

2006 ford crown vic abs code b1596


B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .

Jan 14, 2013 | 2006 Ford Crown Victoria

1 Answer

Reset srs light after replacing seatbelt


To reset the SRS light on an Acura Integra, pull down the SRS service connector. Unplug this connector so you have access to jump the harness. Start with the ignition OFF. Jump the SRS plug. Turn the ignition ON. The SRS light will come on then off.------------------------------------------------------------------------------
autel maxidas ds708

Jan 14, 2013 | 2007 Ford Explorer Sport Trac

1 Answer

2000 Ford Ranger


TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer

Jun 11, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2007 Lincoln MKZ Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...