Question about 2006 Ford Crown Victoria

1 Answer

On my 06 crown victoria my cooling fan isnt coming on i replaced the relay module on the fan yet it still isnt working

Im stuck cant figure this out can someone please help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 436 Answers

There is a coolant temperature control sensor that is probably bad.

Posted on Mar 28, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 58 Answers

SOURCE: 2006 crown victoria - no heat

I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Posted on Jun 21, 2008

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • 108 Answers

SOURCE: 2005 Crown Vic climat contr fan not working Fuses good Motor good

does it have a digital control panel? As this uses an electronic blower speed controller located at the engine compartment (rear engine block) fix on ac phlenum try to shake the connector or wire while the system is on.

Posted on Jan 31, 2010

  • 1 Answer

SOURCE: Location of fuel pump relay on a 2001 Ford Crown Vic

where is the fuel pump relay on a 2001 crown vic p71

Posted on Apr 14, 2010

  • 1 Answer

SOURCE: 2002 Ford Crown Victoria - Air conditioner blower not working

Were u stay

Posted on Feb 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 1500 350 tbi


I believe the voltage regulator is an integral part of this generator, and it is probably causing the problem. I would try replacing the generator.

Jul 04, 2017 | 1990 Chevrolet K1500

1 Answer

Why does my 97 honda accord gas gauge always on full?


Sounds like yourfloat may be stuck. Its located in the gas tank.

Mar 19, 2013 | 1997 Honda Accord

1 Answer

VR commodore not holding charge HELP


Have the alternator tested, any Autozone does the test for free.

Jul 14, 2017 | Cars & Trucks

1 Answer

Location of coolant temp sensor 2000 crown vic


If the sensor was the problem you would have a check engine light on, the fan is operated by the powertrain control module which controls a relay module. You must have the dealer run a scan of the system ans do an active test on the fan operation to determine what is wrong.

Sep 27, 2012 | 2000 Ford Crown Victoria

1 Answer

Where do i find the cooling fan relay for my 2000 ford crown victoria police intercepter?


Should be in the relay box on the passenger side in front of the strut tower.

Sep 21, 2012 | 2000 Ford Crown Victoria

1 Answer

I have a 93 vick p72 ive done a lot to it i have no spark an my fuel pump isnt comeing on im at a loss


check your fuel pump relay and spark control module see if your getting any power to them and if not then the wiring harness will more then likely will have to be replaced good luck hope this helps

Dec 31, 2011 | 1993 Ford Crown Victoria

Not finding what you are looking for?
2006 Ford Crown Victoria Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...