Question about 2004 Mercury Mountaineer

1 Answer

12 mm gauge

What is the 12mm gauge on the battery that is causing it not to start?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

Wire is measured in gauge. Check both terminal conectoins(ends) on both wires for tightness and corrosion.

Posted on Mar 28, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do i have to loosen tension pulley nut first to tension belt with 12 mm bolt


yes you have to loosen of the big nut as that is what maintains the pulley position after adjustment
retension after tensioning the belt

Sep 09, 2017 | Cars & Trucks

2 Answers

12mm to inches in a spannans


7/16 or 1/2 closest, especially if 6 point

Feb 23, 2015 | Cars & Trucks

1 Answer

Radio going off and on..air conditioner going off and on..gauges flickering and won't start


It could be a faulty alternator. This would cause a battery drain since the alternator would not be recharging the battery and supplying operating voltage to the vehicle. Once the battery dropped to about 8 volts then the gauges, A/C, radio and other electronics would start acting crazy. Eventually the car would have shut down, but since you stopped at the post office, that didn't happen. With the battery being so low in charge, that would not allow the car to restart, as there would not be enough current to engage the starter properly. Check the battery voltage. If it seems ok (12-13 volts), try checking it again with someone trying to start the car. A normal battery will see some voltage drop, but a drained one will fall to almost zero with a starter load. Since you have gauges and not warning lights, a discharging battery may have gone unnoticed. If you determine the alternator is bad, be sure to have the battery charged, or if necessary, replaced before using the new alternator. A low battery can cause a new alternator to fail and most alternator warranties will not cover this type of failure.

Sep 05, 2014 | Cars & Trucks

1 Answer

There is a 12mm wire or gauge on battery that is causing my mountaineer not to start. how can i find it with my eyes and where is it?


who sed there is any kinda wire on the battery? if u can't see it , it ain't there?! try this! take all the extra stuff off the key ring, so that u r only holding the key and the keyfob.[keyfob= KLICKER] now start the car? if there is still a no-start condition, then reprogram the key/and fob.PROCEDURE: insert key with fob only. switch the key off/on 8 times. when u r on the 8th time in the ON POSITION, hold down any button the keyfob and hold down for a count of 30. then turn off; take out of key slot. then put back-in and see if this will start the car. it worked for my 2002 explorer!. lol.

Mar 28, 2014 | Mercury Mountaineer Cars & Trucks

1 Answer

Stripped 12mm isuzu bolt hole


You already answered your question partially. The thread size is 12mm. You can a helicoil kit at most parts stores. Buy the kit for a 12 mm and it will have all the necessary items you need to complete the install. The kits are usually pretty inexpensive. I know that NAPA sells these kits over the counter in many different sizes.

Apr 14, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

I need to get access to the starter motor.can i get access from inside the car.is there access to both sides of the engine from inside the car, if so how do you open the drivers side engine inspection...


look under seat there is a lever push down on it seat pops up use recline option to go higher up with seat but to replace starter u have to go under i like to use a long extension with a swivel and a 14 mm there are 3 bolts along the starter and a 12 mm at side of starter un hook the 12mm to starter and one lil wire u squeeze it and pull

Dec 01, 2010 | 1992 Toyota Previa

1 Answer

How do i change the alternator on my 2000 Toyota Tundra?


serpentine belt or standard belt system?if standard lossen 12mm bolt and tensioner on alt.slide left.drop 14 mm bracket bolt then drop slide bolt. dissconect 10mm or 12mm bolt om starter then clip inn alt drop alternater reverse in. diff on serp drop serp by tensioner pulley rest the same

Nov 24, 2009 | Toyota Tundra Cars & Trucks

1 Answer

2001 Toyota 4runner Limited Alternator belt broke.


simple really 12mm wrench an socket and 14 mm wrench an socket. lossen alt bracket 14mm then tesioner 12mm slide back drop belt and reverse. unless condensioner belt in way then dro 12 mm bolts on shiled then back off 12mm bolts on condensioner pulley remove belt follow previous instructions

Nov 22, 2009 | 2001 Toyota 4Runner

1 Answer

Want to replace plugs and ignition wires on a 2004,V-6, 2.7l Tiberon


The air handler you describe is called the 'surge tank' (or I perfer to call it the intake manifold). This manifold must be removed to access the 'rear bank' of plugs & wires on the 2.7 lit V6. There are three or four 12 mm bolts on the rear side of this tank (you'll have to feel for them) and the others are directly under your nose up front down the center of the engine (two long 12mm, three short 12mm and two 12mm nuts. You will want to purchase a new gasket for this manifold (recommended because reused gaskets have been know to leak - rare - but happens). When you put it back together, start all the bolts/nuts finger loose first, do not tighten the rear bolts until after you have torqued the main center-line manifold bolts first ( I believe the torque is 14 to 17 ft lbs) If you don't do these first, you could crack/damage the manifold.

May 20, 2009 | Hyundai Motor 1999 Tiburon

Not finding what you are looking for?
2004 Mercury Mountaineer Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...