Question about Toyota Camry

Open Question

Ob code p0717

How to find the input turbine speed sensor 2005 toyota camray 3.0 engine

Posted by on

  • George Goodwin
    George Goodwin Mar 28, 2014

    I can cancel the code and the car runs good for a short time, also the transmission has to come up to operating temp for the system to malfunction. thanks for help

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
Molson02536
  • 3854 Answers

SOURCE: turbine input speed sensor

NO the sensor is out side the transmission. And it might just be a bad connection due to being out in the eliments. On the 3.1 your going to have to jack up the car to get to it from underneath and you should see it on the passenger side may be on top, Sorry been awhile and carful not to brake the clips that hold the wire to the sensor when disconnecting.
Good luck and hope this helps

Posted on Apr 09, 2009

Ad
  • 316 Answers

SOURCE: input/turbine speed sensor circuit

Your speed sensor, is located on top of the transaxle, near the starter. To access it, remove the battery, then remove the battery tray (4 10mm bolts). You will see wires coming from the lower oxygen sensor, and they snap into the bracket that holds the speed sensor in place. The actual speed sensor has a 2 wire clip on it, and is held in place by the bracket and a 10mm bolt.

Posted on Apr 20, 2009

polarcycle
  • 1392 Answers

SOURCE: fault codes P0722 and P0717

You just need to replace the sensors. If you are mechanically inclined, you can do it yourself. If you don't feel comfortable working on an expensive transmission, take it to the dealer.

Posted on Jun 26, 2009

bschilz
  • 2049 Answers

SOURCE: Transmission code error P2716

The computer wants to know if the transmission is working properly. So it reads the speed of the input shaft and compares it to the speed of the output shaft. It knows which gear you're in because it commanded the transmission to shift into that gear. The turbine speed refers to the torque converter. That's the device that transfers power from the engine to the transmission. Think of two fans facing each other. Turn on one fan and the blades on the other fan will spin. The fan that ISN'T turned on is the turbine. So, with the input shaft or turbine speed, the gear selection, and the output speed, the computer can calculate how efficiently the transmission is working. If the speed is off, it knows that something is slipping inside the transmission. It can then try to boost the fluid pressure to compensate. If that doesn't work, it sets a different trouble code, usually a P0716 code means that the computer has detected a value for the input sensor that's either out of range (way too high or too low), or there's a circuit issue (bad wiring, etc. Should probably get it to a repair shop ASAP before damage is done.

Posted on Sep 19, 2009

Transdoc
  • 829 Answers

SOURCE: Replaced input turbine/speed sensor---Did not fix

Is the sensor threaded or held in with a bolt.

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix a input/turbine speed sensor on a 2009 Chevy Traverse


DTC P0717: Input Speed Sensor Circuit Low Voltage
If you don't know anything about automotive electronic's , sensor electrical circuit's ,your best bet would be to take your vehicle to a qualified repair shop.
Finding a wiring diagram ,reading how this sensor work's an testing the electrical circuit using a DVOM - digital volt ohm meter , going by a factory service repair manual .
Diagnostic Fault Information
Circuit/System Description
The input speed sensor (ISS) is a hall-effect type sensor. The sensor faces the 1-2-3-4 and 3-5-R clutch housing machined teeth surface. The sensor receives 8.3-9.3 volts on the input/output speed sensor (ISS/OSS) supply voltage circuit from the transmission control module (TCM). As the 1-2-3-4 and 3-5-R clutch housing rotates, the sensor produces a signal frequency based on the machined surface of the 1-2-3-4 and 3-5-R clutch housing. This signal is transmitted through the ISS signal circuit to the control solenoid (w/body and TCM) valve assembly. The control solenoid (w/body and TCM) valve assembly uses the ISS signal to determine line pressure, transmission shift patterns, torque converter clutch (TCC) slip speed and gear ratio.

Circuit/System Verification
Engine idling, observe the scan tool Transmission ISS parameter while varying the engine speed. The Transmission ISS parameter should change with the engine speed and not drop out.
Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Your best bet ,take it to a qualified repair shop.

Dec 09, 2017 | 2009 Chevrolet Traverse

1 Answer

Looking for some help with a p0717 code on my 08' trailblazer. Where is sensor located?


DTC P0717: Input Speed Sensor Circuit Low Voltage
Automatic Transmission How to Repair 2006 Turbine Input Shaft Speed Sensor...
Your best bet , take your vehicle to a qualified repair shop.

Nov 26, 2017 | Cars & Trucks

1 Answer

What is the trouble i have a code po0073 ,po717 , po783 , p2784 and rpm block at 2500


  • P0073 Ambient Air Temperature Sensor Circuit High
  • P0717 Input/Turbine Speed Sensor Circuit No Signal
  • P0783 3-4 Shift Malfunction

May 08, 2016 | 2008 Chrysler 300 Touring

1 Answer

Location input turbine speed sensor


it will be located on the exhaust side of the compressor (turbine wheel ) probably near the centre

Mar 28, 2014 | 2005 Toyota Camry 2.4

1 Answer

Code p0717 2009 toyota corolla


Turbine speed sensor no signal

Mar 21, 2014 | 2009 Toyota Corolla

1 Answer

Check engine light car jerking


P0717 Input/Turbine Speed Sensor Circuit No Signal
_______________
gm tech2

Jan 23, 2013 | Cars & Trucks

1 Answer

I have a nissan altima 05 3.5L engine service light just came on and my scanner read these codes P0722 and p0717 p0462 and p0500 are these things i can fix on my own?


CODE PO462 FUEL TANK LEVEL SENSOR VOLTAGE LOW. CODE PO717 TURBINE SHAFT SPEED SPEED SENSOR NO SIGNAL. CODE PO722 OUTPUT SHAFT SPEED SENSOR NO SIGNAL. CODE PO500 VECHICLE SPEED SENSOR CIRCUIT MALFUNCTION. SOUND LIKE YOU HAVE TCM ECM PROBLEMS GETTING TOO MANY CODES. COULD HAVE LOOSE GROUND WIRE TO THE TCM AND ECM.

Aug 06, 2011 | 2005 Nissan Altima

1 Answer

I have code po717 what the problem 2002 sunfire


P0717 - Input/Turbine Speed Sensor Circuit No Signal.

Try to find with your dealer this Bulletin Number: 20730022:
Bulletin Date: 20031001
Category: 980000 OTHER
Summary: SERVICE ENGINE SOON LIGHT ON WITH DIAGNOSTIC TROUBLE CODES P0716 AND / OR P0717, P0730, P0753, P0758, P1860, P1887 OR OTHER MISCELLANEOUS TRANSMISSION TROUBLE CODES SET. *TT

Good luck.

Nov 08, 2010 | Pontiac Sunfire Cars & Trucks

1 Answer

Engine and tcs light on car stalling and rpms


p0134 is oxygen sensor fault code
p0717 is turbine shaft speed sensor (no signal) fault code

May 27, 2010 | 2001 Hyundai XG300

2 Answers

I got a P O 717 code what is it ???


P0717: Input/Turbine Speed Sensor Circuit No Signal.
This code shows because the computer isn't getting any signal from the sensor. Either the sensor is dead or there's a circuit issue (bad wiring, etc).

The Input/Turbine Speed Sensor is the sensor the computer uses to to monitor the the efficiency of the transmission. The computer reads the speed from the input shaft and compares it to the speed of the output shaft. If the speed is off it attempts to correct it by boosting the fluid pressure to compensate. When that fails it trips the P0717 error code. In most cases either the sensor is dead or there's a problem in the wiring harness.

There are issue of intermittent connection trouble with this circuit. That would cause the on off problem.
Hope this helps.

Nov 11, 2009 | 2003 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...