Question about 1998 Chevrolet Cavalier

1 Answer

Does the pully have to come off first before i can remove the bolts holding the pump on?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 159 Answers

Yes.

Posted on Jun 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water pump


you must remove fan shroud. theres a tool for the clutch fan but you can use a impact hammer and a 12" bit (left hand thread) loosen pully bolts before removing belt (belt will hold pully from turning) then remove 4 or 6 bolts holding pump on (look at new pump for bolt amounts not sure) clean serfices and install)

Jan 07, 2012 | 1995 Ford F150 Styleside Regular Cab

1 Answer

How to remove water pump on a 98 oldsmobile intrigue


It is very easy! Take off belt by putting a wrench or socket on tensioner pully and rotating it. belt will come right off. You will have to drain coolant. then take out all of the bolts holding the water pump on. you will have to remove the power sterring pump to get to the very back bolt. Make sure you clean old gasket off of the motor and install new gasket with sealer. reassemble in reverse order.
On '98s at least there is an access hole in the p/s pulley that gives you access to that last bolt
I found no access hole except through the power steering which was easier to remove than the PS pully that a pully remover does not have sufficient room. Two bolts top and bottom through the access holes for the PS pump and it is out of the way of the last water pump bolt.


Dec 07, 2011 | 1998 Oldsmobile Intrigue

2 Answers

Trying to find out where the water pump is located on 2000 ford contour


Your water pump is internal. It will be close to the center of the engine and it will have a pully bolted to it. There should be 4 bolts holding the pully on. remove these 4 bolts and the bolts holding the pump on will be exposed. remove those bolts as well(5-7) of them. And your pump will be free. you may have to use a small flathead screwdriver to pry it out. Be sure not to leave any bearings behind when you remove it. clean entire area with puddy knife or razor blade before installing new one. Install is reverse. Hope this helps.

Jul 23, 2011 | 2000 Ford Contour

1 Answer

I'm changing the Water Pump on my 1999 Ford Taurus Sedan 3.0 V6. There are 3 bolts which are hard to get at. From my stand point, it seems I would have to either take the Main Pully which the engine...


you will have to remove the altnator/power steering mount in order to replace the water pump there and yes you do have to remove the tensionr also, sounds like you are close to having it.....HAVE FUN

Jan 16, 2011 | 1999 Ford Taurus

3 Answers

I'am replacing water pump 2006 grand prix,all bolts are remove but one. I can't remove it because theres a wheel pully in the way. I think it's the power steering pump help.


You may have to remove the pump...
BUT , maybe not...
The pump pully has holes in it... with the power steering belt loose or off ... turn the pully to see if the holes will allign with the bolt you are trying to remove... if not... then the power steering pump must be removed to gain access to the last bolt..

Sep 26, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

WHERE IS THE WATER PUMP LOCATED...2003 ELANTRA


hi from uk fortunately the water pump on your car is not driven by cambelt ! the pump is driven by serp belt the pumps location is = if you look at front of engine view from front wing as you look down front you will see a large pully on left of cambelt covers and this is the water pump access to pump is best by supporting car and removing wheel and then the under wing cover that is secured by screws some advice for you if you intend renewing pump the pump pully is secured by 4 bolts use a 10 mm cranked ring spanner or socket loosen these bolts before you remove the drivebelt as belt holds pully and helps to prevent pully turning as you try to loosen these bolts hope this helps ?

Jan 26, 2010 | Hyundai Motor 2003 Elantra

1 Answer

Pulley removal 91 toyota camry


you should be able to turn the pully to get to the bolt with a swivel and ratchet to remove the pully you need a pully remover and can be rented at schucks or autozone,

Jul 19, 2009 | 1991 Toyota Camry

2 Answers

1999 Buick Park Avenue water pump removal


that is not an idler pully that is the power steering pully if you feel through the holes in the pully you will feel the 13 mm head bolts that hold the pump to the block remove those bolts the pump will drop down and you can then remove the water pump also you have to remove the studs using the inverted torx end on the stud to unscrew it then the mount will come out

May 10, 2009 | 1991 Buick Park Avenue

1 Answer

Having trouble getting water pump out of 94 lantra 1.8 lt


1. Remove the alternator & power steering pump drive belts.
2. Remove four (4) 10mm bolts holding the water pump pullys & remove the pullys.
3. Drain the Radiator (save coolant if intend to reuse).
4. Loosen & remove AC compressor belt.
5. Remove crankshaft pully (22mm bolt).
6. Remove lower timing belt cover (10 mm bolts) to access water pump bolts.
7. Remove the water pump (12mm bolts)
(1) Remove the 2 bolts, then remove the alternator brace (A). (2) Remove the water pump (B) and gasket.
dbb00ee.jpg ef0cc15.jpg 8. Clean mating surface on engine & install new gasket & pump - reassemble. Refill w/50-50 coolant.

Mar 21, 2009 | 2004 Hyundai Elantra

1 Answer

Replace water pump 93 lumina 3.1


no thay are not, you can use a second wrench to hold pully after you remove pully there arew 4 more 10mm bolts holding pump on

Dec 26, 2008 | 1993 Chevrolet Lumina

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...