Question about 1993 Nissan Pathfinder

1 Answer

Hello, i have an old L65 Husqvarna chain saw, i have been lookin for a piston kit, but with no luck, i was told that old style 48mm piston out of Husqvarna model 61 will work in a l65 . Can any one co

L65 Husqvarna. sorry, had to list this under my Nissan pathfinder...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 40,734 Answers

I have a homelite piston running in my Husqvarna edger . Most pistons for engines are all the same if the cc's are the same . they only vary in the gudgeon pin size and the location of the pin in the piston. So take your piston to a small engine wreckers and any piston that measurers the same ,looks the same will do the job. then get a new piston for the make that it came out off and it will fit.

Posted on Mar 28, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is a 2007 Silverado 5.3 engine an interference motor? Vin is 0. Newer style body, timing chain broke


ouch! This is an expensive repair in my experience. You'll need the timing chain and new push rods... and gasket kits. I recommend having a pro do this. Often if the chain breaks people try to start it anyway.... and that causes problems.

Jun 02, 2014 | Cars & Trucks

1 Answer

1999 malibu timming chain broke did valves hit piston


i do not think so gm has large clearence between valves and pistons
also how did timming chain break?i am really dumfounded who told you this?ps:need more info

Dec 20, 2013 | Cars & Trucks

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off


Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.
  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
117016938

  1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Remove the primary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installation.
  1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
117016941

  1. Lower the primary chain with left side sprocket through the left cylinder head opening.
NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
  1. Loosely position left side camshaft sprocket over camshaft hub.
  2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
  3. Position primary chain onto water pump drive sprocket (10).
  4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
  5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
  6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
  1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
117016942

  1. Purge oil from timing chain tensioner using the following procedure:
    1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
    2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
117016943

  1. Reset timing chain tensioner using the following procedure:
    1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
    2. Apply a downward force until tensioner is reset.
NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.
117016944

  1. Install the reset chain tensioner (1) into the right cylinder head.
  2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
117016945

  1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
  2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
  3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
117016946

  1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
117016947

  1. Install camshaft position sensor (2) and connect electrical connector.
  2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
  3. Install upper intake manifold.
NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
  1. Fill cooling system.

Mar 27, 2013 | 2001 Chrysler Concorde

1 Answer

I have a 2004 suzuki forenza and one mechanic told me that the engine was gone and another told me it's probably the timing chain, how do you know which is which?


Neither are hugely wrong.

Does it have a timing chain or belt. If it has an over square engine and the timing chain or belt has snapped, then the valves which let in the fuel and air and let the exhaust gases out travel up and down driven by the cam shaft and the pistons will travel up and down driven by the crank shaft. Without the belt or chain to keep them timed, they meet with great force, at least a top engine rebuild.

To check if the timing chain or belt has broken, you'll need to take the belt/chain cover off. Disconnect the battery first.

If its an under square engine, the pistons have a longer bore to travel, the pistons and valves don't meet.

Jun 25, 2011 | 2006 Suzuki Forenza

1 Answer

Does the 2006 Accord V6 have a timing belt or a timing chain? I was told it's a chain when I bought it new...


the V6 uses a timing belt, what idiot told u it was a chain? a salesman?

GATES Part # TCKWP329 Timing Belt Component Kit W/Water Pump; 5 Components (1 Belt, 2 Tensioners, 1 Idler, 1 Water Pump)
$203.00

Jul 29, 2010 | 2006 Honda Accord

1 Answer

Disc brake spring


best advice is if brakes work then its got into box by mistake,unless its a small coil spring for the brake pad wear sensors

Jun 04, 2010 | 1983 Chevrolet Monte Carlo

1 Answer

My chain on my husqvarna 435 x-torque power saw will not move


Well not exatly a 1999 Park Ave,but I will give it a try.We had several solo brand saws where the plastic parts got hot and melted causing the brake to come on.I could not find a parts breakdown of your saw but there has to be something that makes the brake come on.Part not in the rite place or something mis aligned.Try to get a parts brakdown and make sure that everything is where it is suposed to be.

Jan 18, 2010 | 1999 Buick Park Avenue

1 Answer

Timing chain broke


Hello,Bad Luck with timing chain failure,
Sorry to bear bad news but as far as I know Gm engines are NOT safe i.e. the valve miss pistons. It sometimes isn't too severe if very low rev's i.e. tickover, usually 2 or 3 exhuaust and same inlet. Let's hope no seats.
Cheer's!
Paul 'W'
Onyer~EDson(:0)~[><

Dec 09, 2008 | 2002 Chevrolet Tracker

1 Answer

94 lincoln town car timing chain prob.help!


First, the timing chain runs from the crank around the gears on both cylinder heads. There may be 2 chains. What it does is keep the closing and opening of the valves "in time" with the compression and exhaust stroke of the combustion chamber (pistons).
No compression on the entire left side is not good. If right side is okay then you have 2 chains one for each side. Left side chain must be broke or damaged.
To check the compression without using air , someone had to turn the crank over. If this was done with a bad or broke chain you may have bent valve(s) as well meaning cylinder head rebuilding or replacement.
If you plan on keeping the car for a while consider replacing or rebuilding the engine.

Nov 12, 2008 | 1994 Lincoln Town Car

1 Answer

How to change rear brakes pads on Mazda 3?


there is a kit you can lease from auto zone to insert into the caliper that will turn the piston and compress at the same time its different than the old style where you could use a c-clamp to do it ,,,,,it has to be turned in!!!!!!!!!!!!!!!!!.........the kit will cost 55.00 roughly but you get your money back when you return it do not i repeat do not get the little square block with pegs on it from the zone or advanced auto it won't work its **** and a waste of time.

Aug 01, 2008 | 2004 Mazda 3

Not finding what you are looking for?
1993 Nissan Pathfinder Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...