Question about 2005 Nissan Altima

Open Question

How to remove cylinder head on 2005 nissan altima 3.5 engine

Would like to know how to remove cylinder head

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head removal on 2005 nissan altima 2.5

CYLINDER HEAD REMOVAL

2.5L Engines

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Posted on Nov 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque sequence


already posted previously , i cant take credit for this.follow this link
Cylinder head removal on 2005 nissan altima 2 5 engine would like to...

Apr 25, 2014 | 2003 Nissan Altima

1 Answer

Torque specs for 2005 nissan altima 2.5


According to Haynes Manual, 2005 Nissan Altima, using BRAND NEW cylinder head bolts:

1 - Tighten in sequence (as pictured) to 37 ft-lbs.
2 - Tighten an additional 60 degrees.
3 - Loosen all bolts completely.
4 - Tighten in sequence 26 - 32 ft-lbs.
5 - Tighten in sequence an additonal 75 degrees.
6 - Tighten in sequence an additional 75 degrees.

Mar 23, 2012 | 2005 Nissan Altima 2.5

1 Answer

Do we need to remove the timing chain to remove the cyl head of a 2005 altima


2.5 Nissan altima I assume the answer is yes and be careful reinstalling I believe that is an intrference engine!

Nov 30, 2011 | 2005 Nissan Altima

1 Answer

Need to see a diagram of where the cam shaft sensor is located on a 2004 nissan altima


4 cylinder?at the trans end of cylinder head by where upper rad hose connects to engine.3 wire connector.10 mm bolt secures it.

Mar 19, 2011 | 2004 Nissan Altima

1 Answer

What does p0340 sensor located on 2005 2.4 altima


this is your camshaft position sensor.located on cylinder head near where upper radiator hose attaches to engine......three wire connect and one ten mm bolt secures it.easy to replace.

Feb 15, 2011 | 2005 Nissan Altima

1 Answer

Cylinder head removal on 2005 nissan altima 2.5 engine would like to know how to remove the camshaft to remove the head bolts


CYLINDER HEAD REMOVAL

2.5L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Nov 13, 2009 | 2005 Nissan Altima

1 Answer

My 2003 Nissan Altima 2.5s just started to smoke & knock


what colour smoke? if white, you may have a blown head gasket, remove the radiator cap look for signs of oil in coolant, if low top up with water and start engine,if coolant is trown from radiator this confirms same, also look for external coolant and oil leakk on cylinder head.you can also check cylinders by re moving spark plugs cank engine and see if coolant srays out holes

Jul 09, 2009 | 2003 Nissan Altima

1 Answer

Engine sound humming low and high


If the engine is overheating, that's why the light is on. Its a P0271 code I beleive. Its a "OVERHEATING" code.Dont drive the car. You are loosing coolant or its out of coolant, check the coolant level in the overflow bottle. We have seen some headgasket issues on that model car. I would remove the spark plugs and look into the cylinder for any signs of coolant on top of the pistons. Let me know what you find.

Apr 06, 2009 | 2005 Nissan Altima

1 Answer

Head light 2005 altima


you have to remove the bulbs from inside of the hood in the engine compartment. in some cars you have to remove some "pins' and remove the entire headlight assembly.. You then remove the holder where the lightbulb is located and replace the bulb.

Nov 13, 2008 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...