Question about 2005 Mercury Montego

Open Question

2005 mercury montego stalls, rough idle no throttle responce

Cranks up, rough idle, stalls no throttle responce. Put in failsafe, has throttle but still runs rough, no codes

Posted by on

  • joe kush
    joe kush Mar 30, 2014

    coolant sensor when it is cold put it on scanner and check temp

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
DJGray
  • 56 Answers

SOURCE: 2005 mercury montego message center

LOL!!! I had the same problem. I can't recall the exact steps, but there aren't that many options, so you'll get this. With the car running, press the Info button on the left side. It will cycle through the various statuses of the car. At one point, it will get to the Oil and will tell you something like "Press Reset if New." Press it and hold that darned button until it acknowledges that you changed the oil. It will reset that message from 0% to 100%. It took me a couple of tries to get that to reset. Just keep trying it till it resets. You'll get it.

Posted on Mar 02, 2009

Ad
  • 374 Answers

SOURCE: Change the oil on a 2005 Mercury Montego

Go to a automotive store and tell them you have a 2005 Mercury Montego and what engine it has if there is more then one model and get an oil filter and the oil. Put the car up on ramps and secure it making sure it won't roll back or fall while you are under it. get under the engine and look for the oil pan which should have a bolt in the bottom of it where you can drain the oil. Drain the oil in a proper container and then put the drain plug back in the pan. Then find the oil filter and unscrew it and remove it.. It could be full of oil so watch out and make sure the pan is underneath the filter. Wipe the base where the oil filter screws on and make sure the gasket from the old filter is not still on the engine. Get your new filter and take your finger and put it in one of your new containers of new oil and spread that on the gasket of the new filter. Screw on the filter until the gasket touches the base and then turn only a little more then a 1/4 to 1/2 turn tops. Do not over tighten the filter. Find out what oil the vehicle needs (probably 5-30) and look for the oil cap on a valve cover under the hood. It probably takes 5 quarts but check for sure in your manual or ask when you are at the automotive store. Put the oil in and put the filler cap back on. Now go start the vehicle and make sure you have oil pressure by either the oil pressure guage showing pressure or the oil pressure idiot light goes off and while running check under the car for any signs of leaks. If no leaks then back the car off the ramps and shut the car off on a level surface. Let it sit 10 minutes and check for leaks underneath the car and check the oil dipstick to make sure the proper level of oil is in the engine. Then you are set.

Always check your air filter when changing oil to make sure it is clean as that helps your engine run better and you save gas in the process. Good luck

It is also best to change oil when your engine is warmed up as well.

Posted on Mar 28, 2009

greg_margo
  • 1959 Answers

SOURCE: Need to replace alternator

Here's a link to the alternator diagram:

http://www.chiltonlibrary.com/content/images/0601/images/06017-FREE-g02.gif

Instructions:

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Rotate the drive belt tensioner counterclockwise and remove the accessory drive belt.
  4. Remove the right lower splash shield.
  5. Disconnect the crankshaft position sensor.
  6. Disconnect the wiring harness locators from the alternator splash shield.
  7. Detach the alternator wiring connector.
  8. Remove the positive cable nut.
  9. Remove the alternator splash shield and the alternator.
Here's a link to a website to put the serpentine back on, just insert the year,make,model, and engine size to get the "Routing Diagram" for your car.

http://www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

All the best on your repair.
Greg


Posted on May 30, 2009

  • 5546 Answers

SOURCE: 05 Mercury Montego Throttle control/sensor

Try a salvage yard for the part. As soon as your new car left the lot it became a used car. Used cars run on used parts.
If the old part is a recall they will upgrade you regardless which part is on your car.
Check the internet and enter your part# in the search box of the Browser. You may get lucky for a new part.

Posted on Aug 18, 2009

Keef2011
  • 160 Answers

SOURCE: 2006 mercury montego. DTC

These codes relate to an electronic throttle body fault. Normally its from dirt, hardening oil deposits jamming the throttle body movement. Try cleaning the throttle body first before going down the replacement route. Hope this helps....

Posted on Mar 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 ls it went into failsafe mode. The code was p2100 throttle actuator circuit open. p2110 I changed all coils an throttle body. Still in failsafe mode an rough idle an nuthing when I press the gas.


Sorry to say, But... This is why you don't let parts stores read the codes and you buy parts replace them them, and they are good. Even garages do this. I do this at home. Your problem could be the APP sensor, the throttle body module, wiring , or the PCM. Find a new shop.

Jul 18, 2015 | Cars & Trucks

2 Answers

Cranks up, stalls, rough idle, no throttle responce


possibly the TPS....also check it for vaccum leaks

Mar 28, 2014 | 2005 Ford Five Hundred

1 Answer

Reading codes


Check the wiring to the throttle body, check the supply voltages as well. Check fuses too, it sounds like it received a voltage spike and then lost voltage and is now forcing limited rpm.

May 14, 2013 | 2005 Ford Expedition

1 Answer

96 chevy s10 v6 stalls after i start it up


This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve but always run a OBD2 fault code as well as the cleaning procedure. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Oct 18, 2012 | Cars & Trucks

1 Answer

'97 crown vic cranks but stalls immediately


Idle air control valve. And/or gunked up throttle body, pcv port at throttle where mating to intake manifold.

Jul 08, 2017 | 1997 Ford Crown Victoria

3 Answers

Rough idle stalls at low rpm's


check your transmission fluid,the motor will stall when fluid is low

Dec 06, 2008 | 1996 Jeep Grand Cherokee

1 Answer

Rough idle stalls at low rpm's


hello first check your idle with the car running foot on brake see were your rpm reading is if your below 500rpm check your label underhood for your curb idle setting second see if theres a adjustment screw you can increase were your gas cable lever rest against your set screw underhood if you feel confident enough remove your iac motor idle air control valve if the bore were the end of the pintle extracts out to close has varnish builup our carbon it will stick creating vacuum leak type senario causing stalling rough idle sometimes even no start conditions good luck

Sep 14, 2008 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
2005 Mercury Montego Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...