Question about 2006 Ford Mustang

1 Answer

I replaced a throtte position sensor on a 2006 mustang gt 350 r and the acceleration padle has to be only pushed a little to be in fast acceleration

Rabbit acceleration from start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 242 Answers

It sounds like you did not place it on the shaft correctly try putting it on again

Posted on Dec 15, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 31 Answers

SOURCE: engine temperature sensor located on a 1998 Ford Mustang GT

Left hand side (if facing it), behind distributor, above oil fill.

Posted on Apr 22, 2009

  • 521 Answers

SOURCE: 2005 Mustang GT idleing problem

may be it the problem of another throttle body.also check the ignition switch.

Check all of the battery terminals and cables and check the wires on the starter/selonoid, start from the battery and follow the cable out and check all conections , clean and tighten them and if it still does it the starter/selonoid is bad and needs replacement...

Posted on Aug 25, 2008

emissionwiz
  • 76649 Answers

SOURCE: speed sensor removal 94 Mustang GT

Remove the trans cross member and let the trans drop down (use a floor jack), then you will be able to access it.

Posted on Sep 23, 2008

olwork
  • 237 Answers

SOURCE: a p0340 trouble code and i changed the cam

Code P0340 is a camshaft position sensor CIRCUIT fault. This means it can be a bad sensor, wiring fault (loose connector, short, open), or even a bad PCM. Since you've already changed the camshaft position sensor you've eliminated that possibility. It's time to do some electrical troubleshooting. That, of course, depends upon your skill set for this type of work and equipment (mostly a good dmm and schematics). If you're not equipped for this then you'll likely have to seek assistance from a local shop.

If this reply answers your question then please take a moment to rate this post. - Thanks.

Posted on Jun 30, 2009

1fastbob
  • 301 Answers

SOURCE: my 2002 mustang GT hasits a misfire on cylinder 3

Clean the mass air flow sensor.

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the accelerator pedal position sensor?


You need to replace the accelerator pedal assembly ! That's the whole gas pedal assembly , two bolts hold it fast to the fire wall . Search from over 10 Million Auto Parts P2138 APPS Accelerator Pedal Position Sensor Fix 3 5L Chevrolet Impala

Feb 27, 2015 | 2006 Chevrolet Impala

1 Answer

Mustang error codes P0340 , P0344


These are camshaft position sensor codes. Replace camshaft sensor.

Apr 18, 2017 | 2006 Ford Mustang GT

1 Answer

2001 malibu throtte sticks,


The throttle body needs cleaned its gumed up.Take throttle body off and spray and wipe the inside of the throttle body with a can of throttle body cleaner this should free it up.If that didn't help then you need a throttle position sensor.Reset the computer after any sensor is changed.

Jan 23, 2012 | 2001 Chevrolet Malibu

1 Answer

Hello, my mustang is stopping when i come to a stop. i was told to replace the pedal accelerator pressure sensor. is that correct


Yes, it's your TPS (throttle position sensor). I would get this replaced asap to avoid stalling or uncontrollable acceleration, hesitation, and other things that pretty much increase your chances of an accident tenfold. the rough idling can cause problems in the long run, so go to a parts place or your dealership and just have them replace the throttle body.

Dec 18, 2010 | 2006 Ford Mustang

1 Answer

2006 chevy aveeo throtte position sensor where is located and how do you change and adjust it


THROTTLE POSITION SENSOR IS ON THE THROTTLE BODY ASSEMBLY.ALL YOU DO IS DISCONNECT TPS CONNECTOR AND REMOVE THE RETAINING BOLTS.INSTALL THE NEW TPS IN PLACE.MAKE SURE THROTTLE VALVE IS CLOSED.TORQUE RETAINING BOLTS TO 18 INCH POUND AND CONNECT THE TPS CONNECTOR THATS ALL YOU FINISHED.

Jul 21, 2010 | 2006 Chevrolet Aveo

1 Answer

Throtte position sensor location and how do you change and adjust on a 2006 aveo 1.6 engine


this item is located at the throttle shaft, in the air intake. The sensor is not adjusted, as it takes values from the sensor at each startup. If you have a code that indicates TPS, buy the replacement, and that will help you locate the correct component. Then just carefully switch it out.

Jul 21, 2010 | 2006 Chevrolet Aveo

1 Answer

Low idle. 78,000mi recent very low idle almost stalling. Hwy miles 2006 GT. plugs never changed. TPS not changed or cleaned nor throttle body. Did replace a battery early in the year.


Most often, dirty or faulty 02 sensors will throw off the idle. The 02 sensors and camshaft position sensor basically control all the idle. If TPS was dirty or bad, you would have some hesitation when giving some gas. Bad plug would cause lack of power or misfire.

Oct 21, 2009 | 2006 Ford Mustang

1 Answer

Hesitation Problem while accerating


maybe one or more of the injection nozzles is clogged so when you acclerat it dosent deliver sufficient fuel

May 31, 2009 | 2006 Ford Mustang

2 Answers

2006 Mustang GT engine reving Problem


check the throttle body butterfly for excessive dirt build up. Mine had a rolling idle and would want stall in the mornings. The dealer said it was due to my aftermarket tuner and cold air intake..............just a dirty throttle body that i cleaned.

Apr 03, 2009 | 2006 Ford Mustang

Not finding what you are looking for?
2006 Ford Mustang Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...