Question about Chrysler tc

Open Question

Adjust fog lights

Fog lights are pointed down too far

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: how do i change my fog lights to my 2004 dodge neon

you need to remove the 2 nuts from under the fascia that hold the assembly in. this will give you access to the bulb

Posted on Jan 11, 2009

tripletauto
  • 1450 Answers

SOURCE: hhr fog lights

yes it is you will probably have to have the bcm programmed for the foglight option if your gonna install like factory is

Posted on Sep 22, 2008

  • 65 Answers

SOURCE: how to replace bulb for fog on the front .

You can access it from behind.You have to remove splash shield and go from the underside.

Posted on Nov 29, 2008

  • 1 Answer

SOURCE: fog lights

where is the fuse for the fog lights on a 2005 nissan maxima

Posted on Jan 21, 2009

chuck943
  • 783 Answers

SOURCE: 1st time install of OEM fog lights into a 1999 Mercury Cougar?

Look under the dash near where the headlamp switch mounts and if yours is equipped you should see I think it is a blue 4 pin connector with the following wire colors OG,OG/WH,OG/GN,BK.
This is for the fog lamp relay.If yours has this connector then you will need to purchase a relay ford part number F6RZ-14N089-AA should list for about $10.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear fog lights 2007 suzuki grand vitara


unless the fog lights were fitted after market , there would be no point in rear fog lights
what it would have is reversing lights and they would work with the lights on and in reverse gear

Oct 04, 2016 | Suzuki Cars & Trucks

1 Answer

02 pt cruiser- fog lights aimed too low


Remove the plastic surround, use a flat blade screwdriver to pry off as usually just clipped in! Then there will be 2 or 4 screws securing the light and a single adjuster screw that pivots the light up and down, adjust the pivoting screw till desired light position is reached!

Dec 06, 2014 | Cars & Trucks

1 Answer

How do i adjust fog lights on a 94 ranger?


the main beam of the light should be slightly down from centre of the light. They should be located as close as possible to the road as their purpose is to shine under the fog cloud and reduce refraction of the light through the fog. Any emergency button on the road will be seen through the fog

Aug 08, 2014 | Ford Ranger Cars & Trucks

1 Answer

How do you replace the fog light bulb on 2008 avalanche


    • 1 Open the hood and reach down into the engine bay for the fog light assembly. If you cannot reach the fog light assembly from the top you may need to get underneath the truck to reach it. Remove the electrical plug running to the fog light ballast.
    • 2 Remove the bulb. Unlock the fog light bulb by turning it counterclockwise and pulling it straight out of the assembly.
    • 3 Slide a new bulb into the fog light assembly. The part number you will need for the new bulb will be located on the ballast or base of the old bulb.
    • 4 Turn the bulb clockwise to lock it into the fog light housing.
    • 5 Reconnect the electrical connector to the bulb ballast.

Jan 23, 2011 | 2007 Chevrolet Avalanche LTZ

1 Answer

HOW DO YOU CHANGE THE BULBS OF THE FOG LIGHTS?


The fog lights on most vehicles sit directly underneath the headlight bulbs. The ballast and wiring work just like the headlights, so changing them takes not much time. The procedure to change the fog light is as follows:-- 1) Open the hood and reach down underneath the headlights to unplug the electrical plug from the fog light assembly. Squeeze the top of the release tab and pull the connection off the bulb's ballast. 2)Turn the fog light counterclockwise to remove it from the fog light housing. 3)Install the new fog light bulb.Then connect electrical plugs properly. 4) Test the fog lights by turning it ON. Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 2002 GMC Yukon XL

1 Answer

How do u change a bulb in the fog lights on a


The fog lights on most vehicles sit directly underneath the headlight bulbs. The ballast and wiring work just like the headlights, so changing them takes not much time. The procedure to change the fog light is as follows:-- 1) Open the hood and reach down underneath the headlights to unplug the electrical plug from the fog light assembly. Squeeze the top of the release tab and pull the connection off the bulb's ballast. 2)Turn the fog light counterclockwise to remove it from the fog light housing. 3)Install the new fog light bulb.Then connect electrical plugs properly. 4) Test the fog lights by turning it ON. Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 2003 Ford Focus

1 Answer

Fog lights do not come on either when using headlights or with the fog lamp switch in my 2002 Grand Am SE. Fuse seems to be fine.


REPLACE THE FOG LAMP SWITCH DOWN ON THE STEERING COLM. REMOVE THE PROTEC. PANEL UNDER STEERING COLM. AND GENTLY START TO LOWER THE COLM. WATCH OUT FOR THE SHIFT IND. WIRE- REMOVE IT- LOWER COLM. AND HALF WAH DOWN ON THE TOP SIDE IS THE SWITCH FOR THE FOG LAMP CONTROL IF YOU HAVE ALREADY REPLACED THE ELEC. SWITCH - (PUSH BUTTON OR ROCKER STYLE ).IN THE DASH. IF - - LIGHTS AREON AND THE FOG LAMPS ARE TURNED ON AND THE HEAD LIGHT GO OUT OR WONT CHANGE FROM DIM TO BRIGHT REPLACE HIGH/LOW SWITCH ON COLM. SAME PROCEDURE AS FOG CONTOL SWITCH.

Nov 05, 2009 | Pontiac Grand Am Cars & Trucks

1 Answer

Switch and wire melted


you need to use a heavy gauge wire and a higher amp switch be prepared for a switch to cost you any were from $25-75

Apr 20, 2009 | 1987 Mercury Lynx

1 Answer

1st time install of OEM fog lights into a 1999 Mercury Cougar?


Look under the dash near where the headlamp switch mounts and if yours is equipped you should see I think it is a blue 4 pin connector with the following wire colors OG,OG/WH,OG/GN,BK.
This is for the fog lamp relay.If yours has this connector then you will need to purchase a relay ford part number F6RZ-14N089-AA should list for about $10.

Feb 25, 2009 | 2000 Mercury Cougar

1 Answer

How to adjust front fog lights


Park the car in front of a garage door about 15 feet away, adjust the light so they point slightly down and a little to the right, this si all there is to it, the bolts that hold the adjustment are at the rear of the light behind the bumper..

Oct 05, 2008 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...