Question about 1994 Honda Accord

Open Question

I have a code 54 or 154 on my 1994 honda accord transmission

My d4 light blinks i have 1 long 5 short then 4 short so i dont no if it is 154 or 54

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: 1994 honda accord

The D4 light blinking indicates there is a diagnostic trouble code stored.When a malfunction occurs,the vehicle computer records the code and stores it,then flashes the D4 light to let you KNOW there is a problem.On pre OBD 2 Honda vehicles,1995 and back,Hondas are manual code read,which means you do NOT hook up a scan tool as there is no scan port.The passenger side front kick panel is removed,and a blue 2 wire connector located.Use a jumper wire to short out the connector,then turn the ignition key on,with engine off,not running.This throws the computer into self diagnostic mode,and the D4 or "s" light will flash a series of flashes.The flashes have to be counted,and written down.For example,2 flashes followed by 4 flashes would be a code 24.The code is then looked up with reference material for a description and diagnostic route.Every diagnostic trouble code,has a diagnostic route,for repairing the problem.Again,this informtion,the diagnostic route,is available in reference material from pay sources like All Data Online.After the repair is made,the battery is disconnected to clear the code.Good luck.

Posted on Aug 23, 2008

Ad
  • 259 Answers

SOURCE: Honda Accord 1996 automatic transmission D4 light blinks

i wouldn't worry about it its probably a loose wire somewhere as long as it shifts and drives cool hope this helps regards Jim

Posted on Apr 04, 2009

  • 1 Answer

SOURCE: '92 Accord TCU error 14?

If it feels like you only have 2 gears, and 1st is gone, then it sounds like the transmission computer needs to be replaced. Very easy self done job.

Posted on May 08, 2009

jagjeffery
  • 318 Answers

SOURCE: 92 honda accord lx D4 flashes

you have a transmission fault the D4 light blinks to tell you that there is a transmission problem when the light is blinking the transmission computer put the transmission into limp home mode so it will not shift normally and you should try not to drive it very far when it gets to this stage you need to have the transmission codes check to pin point the problem

Posted on May 29, 2009

philschneide
  • 448 Answers

SOURCE: d4 blinking 1995 honda accord

This is involved. When the D4 light blinks, it is indicating a problem with the input or output systems for the A/T. If you find your Service Check Connector (it should be near or at the top of the kick panel on the passenger's side; it's usually blue and has two holes in it; it is at the end of a wire so don't look for a fixed unit; it is often simply tucked in behind the top of the kick panel. You should pull the kick panel out to find it) you can insert a paper clip so that it connects the two holes. Then, if you turn your ignition to ON II (do not start the car) the D4 light will blink out a code, using both long and short blinks. The blinks have to be carefully counted. Problem codes 1 through 9 care indicated by short blinks. Problem codes 10 through 15 are indicated by a series of long and short blinks (you have to add them together to get the code).

I tell you all this to indicate that the procedure is fairly involved, and since you probably don't have a list of what the codes mean, I would have to say that it would be best to find, if you can, a Honda dealer to read the codes and check your transmission. Most of these problems are connector or sensor related and are usually indicated by the transmission not shifting from one gear to another, or by the transmission jerking hard when it shifts. If your having no problems and you are in a position to not have access to a Honda service department, you can find the backup radio fuse in your engine compartment fuse box and take it out(not with the car running) for 10 seconds or so, then put it back. It will clear the computer. If the D4 starts blinking again, it would indicate that the warning was not just a glitch.
I really hope that this is helpful; I'm sorry if it is only disheartening.

Posted on Oct 29, 2009

Testimonial: "thank you much, ill do that, i hope i can follow that . God bless you. ill keep in touch , maraming salamat."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

D4 light on 94 accord blinking


It will blink a set number of times to tell you what diagnostic trouble code it has. I would first check the fluid to make sure it is still red in color and not too low just to make sure that your not doing any damage to the transmission by driving it. Then you can get a cheap repair manual like a "Haynes" manual from any auto parts store.
I hope this info helps!~subyguru~

Mar 31, 2012 | Honda Accord Cars & Trucks

1 Answer

D4 light on no matter what gear i'm in. 95 Honda Accord LX 4-cylinder. Already replaced solinoid, speedometer, fan,


The D4 light is coming on to tell you that there is one or more fault codes set in your transmission control module. The only way to retrieve codes on the 1995 models is to read "Flash Codes" output by the D4 light. (See instructions below)

RETRIEVING FLASH CODES USING THE D4 LIGHT
If fault codes are present, the D4 light will "blink" when the ignition is turned to the RUN position and will remain on at all times when the engine is running.
To retrieve the flash codes, turn the ignition switch off.
Install a jumper wire between the service check connector terminals.
The service check connector is a gray, 2-pin connector located on the PCM/TCM cover under the passenger side of the instrument panel. (See picture below)

CAUTION: DO NOT use the 3-pin located next to the service check connector.

Installing the jumper will place the PCM/TCM in diagnostic test mode.
Turn the ignition to the RUN position. Codes will be output by blinking the D4 light.
Note the number of blinks from the D4 light. A short blink indicates a single digit flash code. A long blink equals 10 short blinks. For instance one short blink indicates code 1. One long blink and four short blinks indicates code 14. If there is more than one fault code, they will be output one at a time from the lowest numbered code to the highest numbered code. It is recommended that you read the code or codes several times to make sure that you are reading it correctly.

Once you have retrieved the fault code(s) re-post your question and include the information for what codes you have and someone can then help you locate the cause of the problem.

May 22, 2011 | Honda Accord Cars & Trucks

1 Answer

The "D" light is blinking regard less where the


Flashing D4 light is an error from the TCU (transmission control unit), so you got something going on with your transmission. If you want to pull the error code, remove the passengers side kick panel and look for a pair of wires with a blue connector at the end. Stick a paper clip or some other piece of wire into each hole of the connector to short the wires. Put your key in the ignition and turn 2 clicks. The D4 light will flash the code...short flashes=1 and long flashes=10. Add the number of short and long flashes to get your code. Errors are below:

0-Transmission control unit (TCU) faulty.
1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.

Dec 18, 2010 | 1993 Honda Accord

1 Answer

I have a 4 cilinder Honda Accord 1998, today for the first time the engine light swithced on and the "D4" light started blinking at the same time that the "D3" light was on (the gear setting I was in at...


D4 light on means transmission fault of some sort. Have the vehicle scanned as soon as possible, because it might be a minor glitch, and the transmission could be saved. Have in mind that these transmissions (1998-2002)are notoriously prone to fail around 60-80000 miles. If rebuilt with the remedial kit (i dont remember the proper name for this), the transmission tends to work normally.

Sep 30, 2010 | 1998 Honda Accord

1 Answer

92 honda accord D4 light flashing


Flashing D4 light is an error from the TCU (transmission control unit), so you got something going on with your transmission. If you want to pull the error code, remove the passengers side kick panel and look for a pair of wires with a blue connector at the end. Stick a paper clip or some other piece of wire into each hole of the connector to short the wires. Put your key in the ignition and turn 2 clicks. The D4 light will flash the code...short flashes=1 and long flashes=10. Add the number of short and long flashes to get your code. Errors are below:

0-Transmission control unit (TCU) faulty.
1-Lock-up solenoid 'A' circuit open or shorted.
2-Lock-up solenoid 'B' circuit open or shorted.
3-Throttle Position Sensor circuit open or shorted.
4-Vehicle Speed Sensor open or shorted - No signal from speedometer.
5-Shift Lever Position Switch circuit shorted.
6-Shift Lever Position Switch circuit open.
7-Shift Solenoid 'A' circuit open or shorted.
8-Shift Solenoid 'B' circuit open or shorted.
9-Counter shaft or transmission speed pulse generator open or shorted.
10-Coolant Temperature Sensor open or shorted.
11-Engine RPM (Ignition coil signal) open or shorted.
12-(No code 12 used)
13-Main shaft speed pulse generator open or shorted.
14-Linear (line pressure control) solenoid open or shorted.
15-Kick down switch circuit shorted.

Aug 11, 2010 | 1992 Honda Accord

1 Answer

When i put my 92 honda accord into d4 it starts blinking and wwont take off. also one of my belts will make noise


This is a bit involved. When the D4 light blinks, it is indicating a problem with the input or output systems for the A/T. If you find your Service Check Connector (it should be near or at the top of the kick panel on the passenger's side; it's usually blue and has two holes in it; it is at the end of a wire so don't look for a fixed unit; it is often simply tucked in behind the top of the kick panel. You should pull the kick panel out to find it) you can insert a paper clip so that it connects the two holes. Then, if you turn your ignition to ON II (do not start the car) the D4 light will blink out a code, using both long and short blinks. The blinks have to be carefully counted. Problem codes 1 through 9 care indicated by short blinks. Problem codes 10 through 15 are indicated by a series of long and short blinks (you have to add them together to get the code).

I tell you all this to indicate that the procedure is fairly involved, and since you probably don't have a list of what the codes mean, I would have to say that it would be best to find, if you can, a Honda dealer to read the codes and check your transmission. Most of these problems are connector or sensor related and are usually indicated by the transmission not shifting from one gear to another, or by the transmission jerking hard when it shifts. The belt problem you are hearing is probably related.

I hope this is of some help.

Nov 02, 2009 | 1992 Honda Accord

1 Answer

D4 blinking 1995 honda accord


This is involved. When the D4 light blinks, it is indicating a problem with the input or output systems for the A/T. If you find your Service Check Connector (it should be near or at the top of the kick panel on the passenger's side; it's usually blue and has two holes in it; it is at the end of a wire so don't look for a fixed unit; it is often simply tucked in behind the top of the kick panel. You should pull the kick panel out to find it) you can insert a paper clip so that it connects the two holes. Then, if you turn your ignition to ON II (do not start the car) the D4 light will blink out a code, using both long and short blinks. The blinks have to be carefully counted. Problem codes 1 through 9 care indicated by short blinks. Problem codes 10 through 15 are indicated by a series of long and short blinks (you have to add them together to get the code).

I tell you all this to indicate that the procedure is fairly involved, and since you probably don't have a list of what the codes mean, I would have to say that it would be best to find, if you can, a Honda dealer to read the codes and check your transmission. Most of these problems are connector or sensor related and are usually indicated by the transmission not shifting from one gear to another, or by the transmission jerking hard when it shifts. If your having no problems and you are in a position to not have access to a Honda service department, you can find the backup radio fuse in your engine compartment fuse box and take it out(not with the car running) for 10 seconds or so, then put it back. It will clear the computer. If the D4 starts blinking again, it would indicate that the warning was not just a glitch.
I really hope that this is helpful; I'm sorry if it is only disheartening.

Oct 29, 2009 | Honda Cars & Trucks

8 Answers

D4 blinking, spedometer not working, check engine light on


Hi, a few questions 1st. Did your mechanic check for engine codes? Is your Honda a v-6 or 4 cylinder?
The flashing D4 light indicates a possible transmission malfunction. You should avoid rapid acceleration until the cause of the light blinking is determined.
If you have the V-6, there is a diagnostic port to connect a scan tool to read any stored engine codes that have turned on the check engine light. This port is located behind the ashtray in the center console (most cars did not have this til 96).
If you have the 4 cyl engine, there is a service connector located under the dash on the pass. side. Inside the connector is what looks like a 2 wire plug should be attached. Take a paper clip, unbend it, and insert the 2 ends of the clip into the connector to 'jump' it. Turn the ignition switch to the on position (don't start the vehicle), and the check engine light will flash. Count the flashes, short flashes are for code #'s 1 to 9 (single digit code), a 2 digit code will be a long flash for the 1st digit, followed by a short flash for the 2nd digit. If there is more than one code, they will be separated by a pause. They will repeat so you can count them and write them down. Let me know what the code #'s are so I can help further. Curt

Jul 22, 2009 | 1995 Honda Accord

2 Answers

92 honda accord lx D4 flashes


you have a transmission fault the D4 light blinks to tell you that there is a transmission problem when the light is blinking the transmission computer put the transmission into limp home mode so it will not shift normally and you should try not to drive it very far when it gets to this stage you need to have the transmission codes check to pin point the problem

May 29, 2009 | 1992 Honda Accord

1 Answer

1992 honda accord.The gear shift will be in D 4 But the shifting lights for Park will come on and both lights will start blinking.


The d4 light will blink when there are codes in the tcu. You need to have the codes read on the transmission computer.

Feb 18, 2009 | 1992 Honda Accord

Not finding what you are looking for?
1994 Honda Accord Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...