Question about 2000 Chevrolet Blazer

1 Answer

I own a 99 chevy blazer but I have lost the keys and do not have the money for a locksmith to come out! How can I start it without a key and if I use something other than the key will the passlock sys

How can I start it without a key and if I use something other than the key will the passlock system engage and shut off the fuel!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Write down the vin number call the dealer they can make key for you

Posted on Mar 27, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Shadowmaru
  • 33 Answers

SOURCE: passlock problem

Lock your door with the keyless entry (If you have it) if not just lock all your doors, pop your hood and shut all the doors. Then remove the negative off your battery for about 30 seconds minimum. Then reconnect the negative of the battery, close your hood, unlock the drivers door with either the key or the keyless system if you have it, and try to start your car. If that does not work then it is not your theft system but a bad grounding of your battery.

Posted on Feb 11, 2009

  • 141 Answers

SOURCE: replaced multiswitch in 2000 chevy s10 blazer and now the car won

at the base of the steering column there a orange and white wires these two wires come from the ing switch, you will see the connector that they go to disconnect that take a ohm meter, take the leads one lead to one wire the other lead to the other there should be res, if there is not, try a different setting . take your ing key on the the key you will see a chip take two leads from your meter and either side of the chip place the leads you will see a res reading, you should see the same at the orange and white wires . if you do not replace the ing switch the switch will come with these wires. replacing the switch takes a couple specail tools good luck and let me know how it gose

Posted on Dec 22, 2008

csmock132
  • 4669 Answers

SOURCE: passlock

The black should be ground, The orange should be 12 volts, there should be another wire. Yellow? signal wire.

Posted on Mar 02, 2009

mcgyver468
  • 710 Answers

SOURCE: wont start

fuel pressure should spray pretty far. at least 2ft+. pump may not be delivering enough pressure. have pump replaced

Posted on Apr 22, 2009

Molson02536
  • 3854 Answers

SOURCE: the stupid passlock!!!!

If you tried to hot wire the ignition, you may have shorted out the pass lock wire in the ignition switch. You may have to replace the ignition switch. Try the relearn process, it takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK. Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps. Keep me posted, be glad to help.

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to start a Ford Contour with out my key


Probably can't be done if it is late enough to be fitted with a security system. In that case the key will have a coded transponder which the system will recognise and send a signal the the engine management to switch it on.

You either need a correctly coded key or remove the engine ECU and have it decoded.

Jan 23, 2016 | Ford Cars & Trucks

1 Answer

99 blazer security light stays on


The security light means the computer is not reading the chip in the key.
You should have a sensor in the key lock and a chip on the key programmed for the security system.
I would try a spare key first. If you don't have one, you can get one from the dealer or some locksmiths.
If you know you have a good key, the problem may be with the sensor in the lock cylinder.

Jul 23, 2012 | 1999 Chevrolet Blazer

3 Answers

I lost my keys to my Chevy blazer 1996 yesterday ...a mechanic came by and removed the Lear latch lock to make a new key ...but at the end he was unsure if I could start the ignition with it ....is the...


No your ignition is a different lock but it could be keyed the same by a locksmith or possibly one could be ordered to match it from the factory based on your vehicle identification number.

May 26, 2012 | 1996 Chevrolet Blazer

1 Answer

How to unlock a 1983 chevy blazer without a key?


Use a Slim-Jim opening tool. Depending on the weather stripping, it may also be possible to use a coat hanger to grab the inner door handle and pull it open.

Use your Autoclub memberships, Insurance company memberships to get help. A locksmith has MASTER keys to fit in the doorlocks. The Locksmith comes out with a box of Masters for GM trucks and inserts them one-byone into the doorlock until he finds the right one.

Jan 23, 2012 | 1983 Chevrolet Blazer

1 Answer

Lost my key


call the chevy dealer, give them info they ask for, probally ask for vin number, they should be able to get you a key replacement...also search your couch real good, seriously,

Jun 28, 2010 | 2000 Chevrolet Cavalier

1 Answer

My 1999 Chevy Blazer has a key for the ignition and a key for the doors. I lost the only key I had for the doors. Although I can use the clicker to get in, can I get a replacement key for the doors, how...


depends on which key was original==an original key can be cut but are the doors original or ignition vin number will be used to look up key cut code or check with a certified locksmith some of them work with the dealers for key problems

Oct 23, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...