Question about GMC Sierra 1500

1 Answer

Power steering filter

Where do you find these and how do you install one?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • GMC Master
  • 2,620 Answers

You can find them at www.rockauto.com and you just splice them into the return line.

Posted on Mar 27, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a new power steering pump. should i also replace the filter?


There is no filter for the power steering. That car has Variable Assist Power Steering (VAPS). Make sure the pump is really the part you need before installing. There are a lot more components to that steering system that could cause problems. Could be pressure switch or control valve. I don't know what your symptoms are but, you should have someone look at it that is familiar with that system and able to properly diagnose the problem before you start changing parts.

Oct 02, 2014 | 1998 Ford Taurus

2 Answers

Power steering filter


Is it full of power steering fluid ? How are the hose's high pressure and low pressure ? Did you bleed the air out after changing the pump ? There is no filter .
Verify power steering fluid level per operating specification. Refer to Checking and Adding Power Steering Fluid.
Start the engine. Rotate steering wheel from left to right. Check for sign of cavitation or fluid aeration (pump noise/whining).
Verify the fluid level. Repeat the bleed procedure, if necessary.

Apr 23, 2017 | Pontiac Grand Prix Cars & Trucks

1 Answer

Power steering filter


As far as I know only medium and large trucks have a power steering filter. If you are asking for a large truck or Bus/RV then more information is needed on the make and model of vehicle. The filter is usually located at or near the output of the power steering pump.

Aug 02, 2012 | Cars & Trucks

1 Answer

I have 2005 nissan altima with a 2.5s...im looking for the power steering filter and dont know where it is located?


there is no power steering filter. dont even worry about any power steering filter. those cars dont have any power steering issues.

Sep 10, 2011 | 2005 Nissan Altima

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

Cant find were to put powersteering fluid


Power Steering Pump Removal & Installation 3.8L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Place a drain pan under the vehicle.
  3. Remove the accessory drive belt from the power steering pump pulley.
  4. Raise and safely support the vehicle.
  5. Remove the right front tire and wheel assembly.
  6. Remove the hoses from the power steering pump.
  7. Remove the mounting bolts and the power steering pump from the engine.
  8. Remove the reservoir and pulley from the pump if necessary.
To Install:
Power steering pump removal/installation (3.8L engine) gm-08-38-480.gif

  1. If removed, install the power steering pump reservoir and pulley on the power steering pump.
  2. Position the power steering pump to the engine and install the mounting bolts. Tighten the bolts to 25 lb ft (34 Nm).
  3. Install the pressure and return hoses to the pump.
  4. Install the right front tire and wheel assembly.
  5. Lower the vehicle.
  6. Install the accessory drive belt.
  7. Fill and bleed the power steering system.
  8. Inspect the system for leaks.
  9. Remove the drain pan from under the power steering pump area.
3.4L Engine To Remove:
  1. Place a drain pan under the power steering pump.
  2. Remove the coolant reservoir.
  3. Remove the pulley from the power steering pump.
  4. Remove the wiring harness near the power steering pump and place it out of the way.
  5. Disconnect the fluid hoses from the power steering pump.
  6. Remove the mounting bolts from the power steering pump and remove the pump.
To Install:
Power steering pump removal/installation (3.4L engine) 88008g71.gif

  1. Position the power steering pump assembly to the engine and install the mounting bolts. Tighten the mounting bolts to 25 lb ft (34 Nm).
  2. Install the wiring harness in its original position.
  3. Install the pulley on the power steering pump.
  4. Install the coolant reservoir.
  5. Fill and bleed the power steering system.
  6. Inspect the system for leaks.
  7. Remove the drain pan from under the power steering pump.
prev.gif next.gif

Sep 18, 2010 | 2000 Chevrolet Impala

2 Answers

Whining when i press gas


normally, the only part of your automatic transmission that will make a whining noise is the pump. it usually whines when iether the fluid is low or more commonly when the transmission oil filter is getting plugged up.

the power steering pump will also make a whining noise too.

turn the wheel all the way to the right and hold steady pressure against the stop. this puts maximum force on the power steering pump and, if the power steering pump is the one making the whine, it will change the sound of it. (usually louder).

if the trans pump is making the whine noise, it should sound different in neutral compared to drive. this test will really only work if it make the noise without the vehicle moving. if it wont do it at idle hold the rpms at 2000 or so.

if you decide the noise is coming from the transmission, and the transmission filter has not been replaced (assuming you installed a used transmission), replace the filter by removing the oil pan.



oh and also, if it is the power steering pump you should be able to make it make the whining noise while the vehicle is stationary. if it wont make noise unless its moving its not the power steering pump.

Mar 23, 2010 | 2003 Chevrolet TrailBlazer

3 Answers

If power steering pump is replaced, is it possible to damage the steering rack during the replacement of the pump?


NO. The rack usually fails because no one changes P/S Fluid every two years or so. Now if a new rack is installed and you don't flush the cooler and install a filter in the return line,you loose the new rack again from contamination from the first rack. That's a common poor work practice,even though every rack comes with a tag and instructions warning of this.

Feb 09, 2010 | 2002 Audi A6

1 Answer

Power steering acts like its low on fluid at an idle. Rack & pinion & pump are a year old. I have an inline filter installed. Removed filter to see if it was pluged, no difference. Plenty of fluid...


Was it a reman pump and rack? You most likely have a problem with the pump again. If it is hard to steer both ways, it will be the pump. If it is hard to steer only one way, it will be the rack.

Jul 28, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...