Question about BMW X3 Series

1 Answer

Sump remove How do I remove the sump from a 2LTR Diesel X3 N47 Engine?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

You will have to remove the front axle unit / subframe. The engine has balance weights in the lower part of the engine so be careful. Good luck.

Posted on Dec 20, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Iseki 4320 engine problem. Diesel fuel filling the sump. Seems that fuel leaks into the sump when the engine has not been run for an extended period. We only acquired the tractor recently.


pull the fuel pump and have it overhauled by a specialist diesel shop
the fuel is leaking past worn elements and shaft seals you could always put a tap in the fuel line just before the pump but that would mean remembering to turn it on and off for operations

Aug 31, 2017 | Cars & Trucks

1 Answer

2008 dodge ram 4.7 ticks at start up. i heard if i put a half quart of ATF in it that i will clean it out and it will stop. true of false


false-- Remember that you require a certain viscosity oil in the sump and any oil that thins out the sump oil will cause damage to the bearings. Check that the oil filter in use has a non drain back valve in it to retain oil in the hydraulic tappets on shut down. The best oil to clean out an engine is diesel oil as used in diesels. The viscosity is right and the extra detergents in the oil will remove all sludge in the engine. The problem is because it is doing the job then the filter has to changed every 5000miles or sooner depending on the condition in the engine. As a point of interest diesel oil can be used in a petrol engine all the time.

Oct 08, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

Hyundai tucson problems


check for emissions leaks.. and add some cetane boost to the fuel as well as injector cleaner.. may spray injector cleaner into the intake snorkel..

Dec 27, 2013 | Cars & Trucks

1 Answer

Kubota M 5030 2.8 6 cyl. Diesel in oil sump. Why?


Diesel gets in the sump from an seal leaking in the fuel pump through to the drive gear and out into the sump. If it has an inline pump( one where the injector lines are in a row at the top of the pump) the fuel will be leaking past the plunger elements and into the pump sump which then drains back tot he engine sump. IF it is slight but consistent sometimes injectors will dribble when shut down and the fuel will by pass the piston rings into the sump. Talk with a diesel pump and injector repair specialist for any faults particular to the Kubota fuel system

Apr 03, 2013 | Cars & Trucks

1 Answer

Jag xtype 2.0D 2004 Glow plug light flashing.Engine malfunction light on .No loss of power.Hhappened just after refuelling


jaguar x-type 2ltr diesel 2004 the glow plug warning light flashing, was told dirty fuel on fault code all fuel changed and filters. No problems for 20 miles untill engine was put under power on high revs went into limp mode, warning light glow plug falshing again? any ideas thanks.

Feb 09, 2011 | 2004 Jaguar X-Type

1 Answer

Freelander 2ltr diesel 1998 timingbelt diagram


is this the engine with the injector pump at the back of the engine

Dec 07, 2010 | Land Rover Freelander Cars & Trucks

1 Answer

Engine removal and intsalling!!


weather its diesel or V6 petrol you can remove small tin engine sump and oil pick ups then undo all 4 diff case mounting bolts to chassis one at a time remove and put back in only a few turns this then drops diff assembly down then install motor
works a treat!!!

you could be lazy and bend lip of tin engine sump over bolts in rear left side with hammer this works also but still is a bit of a struggle over that diff.

Aug 30, 2009 | 1999 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...