Question about Land Rover LR3

Open Question

Change vacuum pump in discovery 3 TDV6

Where can i find the vacuum pump on discovery 3 TDV6 and how do i change it

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 54 Answers

SOURCE: HOW DO YOU RESET THE SERVICE INTERVAL INDICATOR ON

You can take it to a garage that can run diagnostics on your vehicle, as you need to plug in a laptop that has the diagnostic program on it and switch off the indicator. This also goes for engin mangement lights, airbag warning lights etc. As long as the garage has the correct diagnostic program they caan reset all the dash lights you want resetting. Hope this helps ;)

Posted on Apr 15, 2010

Ad
  • 1 Answer

SOURCE: trying to find crank sensor on a discoverry 3

You will find the crank sensor near the turbo, you will need to remove the body and the gear box to locate the crank sensor.

Posted on Nov 21, 2010

SOURCE: i need to know where

Hi Angie, The fuel filter is inside the fuel tank and fits onto the high pressure fuel pump. Regards Johngee10

Posted on Jul 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to DIY 2004 discovery cruise control not working?


land rover used a vacuum set up check the vacuum line at the actuator, usually crack at the actuator, cut end off and put back on. also check to see if brake lights are on all the time when key is on if so then brake switch, also would add check the fuse first and the vaccum pump may need replaced if you dont find anything with vacuum lines, fuse, brake switch, replace the actuator before you replace the pump.

Feb 22, 2017 | 2004 Land Rover Discovery

1 Answer

No Power Supply from the fuse box to the computer box on a landrover discovery 3 hse tdv6 2007 model


Most likely blown engine fuse, open the drivers manual , grab your volt meter and test each side of the fuse for battery voltage, if voltage on one side only replace fese.

Nov 13, 2016 | Cars & Trucks

1 Answer

Discovery 3 MY09 TDV6 front end whine under load acceleration


When you say whine does it only occur under acceleration only? If so most likely the wheel hub assembly or some will say wheel bearing but on these vehicles it is complete hub assembly. If you turn or swerve one way then the other does it go away in one direction? If so another strong indication of hub wearing out. If not, and it is a really high whine with acceleration it is also possibly the transmission. I have heard of this complaint before, it's not a sign of failure just a noise that develops due to the pressure placed on bearing under a load. First change fluid and filter for tranny after a good flushing. Replace with high quality fluid and a bottle of transmission seal restore product. Go 1000 miles, change fluid again, if noise is still there turn up radio.
Sorry but just a whine under acceleration isn't a lot to go on. But I'm willing to bet wheel hub. 9 out of ten front end whine complaints is wheel hub or bearing especially on a heavy 4x4 suv

Nov 03, 2017 | Land Rover Discovery Cars & Trucks

1 Answer

I need to know where a fuel filter is on a landrover discovery tdv6


Hi Angie, The fuel filter is inside the fuel tank and fits onto the high pressure fuel pump. Regards Johngee10

Jul 24, 2011 | 2001 Land Rover Discovery Series II

1 Answer

Reduced performance & DCP full my wife cannot


If you own a 3.0l TDV6 Discovery 4, it requires a software upgrade for the Powertrain Control Module... Its due to a injector control error with the current software of the PCM.

Dec 18, 2010 | 2010 Land Rover LR4

1 Answer

How to get access to replace the alternator on my Discovery 3 TDVS. I have removed the air-intake pipe from the air-box and the top part of the fan cowling. My question however is whether the fan blades...


hi
yes you will have to take the fan off to get to the tensioner
and the alternator once the fan is off (with a 27or32 spanner i think) everything else is easy-ish. dont be shy to give it ago people, Alternators are easy to do even on big 4x4s like the discovery 3 tdv6.
hope that helps
thanks
Muhammad.

Apr 21, 2010 | 2006 Land Rover LR3

1 Answer

HOW DO YOU RESET THE SERVICE INTERVAL INDICATOR ON A 2006 DISCOVERY 3 TDV6


You can take it to a garage that can run diagnostics on your vehicle, as you need to plug in a laptop that has the diagnostic program on it and switch off the indicator. This also goes for engin mangement lights, airbag warning lights etc. As long as the garage has the correct diagnostic program they caan reset all the dash lights you want resetting. Hope this helps ;)

Apr 15, 2010 | 2006 Land Rover LR3

1 Answer

Trying to find crank sensor on a discoverry 3


You will find the crank sensor near the turbo, you will need to remove the body and the gear box to locate the crank sensor.

Jul 06, 2009 | 2006 Land Rover LR3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80608 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...