Question about 1955 Morris Minor

Open Question

Door glass remove

Removing door glass

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In the process of removing the metal /glass door panel to access the cushion the door fell off. now the metal door cover is loose in lower left corner...what screws will remove door panel - i forgot


I would be interested to know what you are working on that has a metal and glass door panel, and how on earth removing it would make the door fall off?

Oct 04, 2016 | Cars & Trucks

1 Answer

Rear door glass removal


After you get the regulator assembly out of the way try removing any tracks inside the door that can be removed and see if you can then rotate the glass.

Jan 16, 2014 | 2009 Dodge Journey

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

Electric window feel down broken mechanism


Glass & Regulator

zjlimited_228.jpg

Fig. View of inner door frame and window regulator assembly

  1. Lower the window glass and remove the door panel.
  2. Carefully peel off the door screen so that it can be reused.
  3. Raise the window enough to reach the regulator bolts, hold the glass underneath and unbolt the glass from the regulator.
  4. To remove the glass, raise the glass by hand and tilt it as necessary to remove it from the track.
  5. To remove the regulator, lower the glass carefully to the bottom of the door and remove the bolts to remove the regulator.
  6. Installation is the reverse of removal. Tighten all bolts to 61 inch. lbs. (7 Nm).
zjlimited_229.jpg

Fig. Installing the door glass regulator



Motor

  1. Remove the door panel.
  2. Carefully peel off the door screen so that it can be reused.
  3. Unbolt the window from the regulator and carefully lower it to the bottom of the door.
  4. Disconnect the wiring and remove the motor mounting bolts.
  5. Remove the 3 guide rail bolts and lower the motor and guide rail assembly out the bottom of the door.
  6. Installation is the reverse of removal.
NOTE The upper cable must be below the guide rail mounting bracket.
Showing window regulator motor, or assembly carrier with window regulator, removal/installation

zjlimited_230.jpg

Fig.

NOTE The illustration shows the removal and installation of the window regulator motor/assembly carrier with the window regulator on the rear doors. The procedure for removing and installing on the front doors is the same.
zjlimited_231.jpg

Fig. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier. Remove the screws and take off the window regulator motor

  1. Slide a hammer shaft between the window guide and the assembly carrier until the end of the hammer shaft presses against the assembly carrier.
  2. Remove the screws and take off the window regulator motor.
To install:
  1. The gearing will move when the window regulator motor is removed; it is then no longer centered. The gearing must be aligned when the window regulator motor is installed until the window regulator motor is centered again.
  2. Installation is the reverse of the removal (see illustration).

Motor & Regulator

NOTE The illustrations in the procedure show the replacement of the window regulator motor/carrier assembly with window regulator for rear doors. The procedure for front doors is the same.
  1. Remove the front or rear carrier assembly.
  2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
  3. Unfasten the bolts (1) and remove window regulator.

    zjlimited_232.jpg

    Fig. Unfasten the bolts (1) and remove window regulator

To install:

NOTE By removing window regulator motor, gearing shifts, it is not centered.
zjlimited_233.jpg

Fig. By removing window regulator motor, gearing shifts, it is not centered

  1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
  2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
  3. Carrier assembly with window regulator, installing:
    1. For replacement part carrier assemblies, the gearing is secured in place with a cable tie.

      zjlimited_234.jpg

      Fig. For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)

    2. Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.
  4. Remove the cable tie .
  5. By removing window regulator motor, gearing shifts, it is not centered.
  6. When installing window regulator motor, gears must be aligned until window regulator motor is centered again.
  7. Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.

Hope this helps to solve it.

Dec 14, 2010 | 2002 Volkswagen Jetta TDI

1 Answer

How to replace a broken wing mirror on a Volvo S40 1980 model



Power Dr Mirrors Diagnosis & Testing


Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Disconnect the negative battery cable. The mirror inside cover trim The door panel The electrical connector to mirror motor The nut attaching mirror assembly to door frame The outside rear view mirror

    0900c152801c11d4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing cover trim and nut
    Removing cover trim and nut

    0900c152801c11d5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing mirrored glass from assembly
    Removing mirrored glass from assembly

  3. Remove the mirror glass:
    1. Fold the mirror glass forwards and inwards as illustrated.
    2. Grasp and pull the mirror glass lengthways until it releases.
    3. Work the glass out.

  4. Remove electric motor:
    1. Remove the 3 screws from behind the mirrored glass.
    2. Separate the connectors
      NOTE Remember the positions of the connectors.
    3. Remove the mirror motor.

      0900c152801c11d6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Removing connectors and screws holding mirror motor
      Removing connectors and screws holding mirror motor



To install:
  1. Install or connect the following:

    The electric motor The electrical connections The 3 screws that go behind the mirror Install the terminal pins Fold out the mirror mounting on the motor Hook the mirror glass into the inner mounting Press the mirror glass into place. Place mirror in position in door

    0900c152801c11d7.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Reattaching mirror and electric motor connectors
    Reattaching mirror and electric motor connectors

  2. Install or connect the following:

    The nut attaching mirror assembly to door frame The connector The door panel The mirror inside cover trim The negative battery cable

Oct 23, 2010 | 2000 Volvo S40

2 Answers

Need to replace broke window on 93 ford tempo.Pass. side


Door Glass, Front Removal
  1. Remove door trim panel and watershield. Refer to Section 01-05. ani_caut.gif CAUTION: Prior to removing center pins from the rivet, it is recommended that a suitable block support be inserted between door outer panel and glass bracket to stabilize glass during rivet removal. Remove center pin from each rivet with a drift punch. Using a 1/4-inch diameter drill, drill out remaining rivets as damage to plastic glass retainer and spacer could result.
  1. Remove two rivets attaching glass to run and bracket assembly.
  1. Remove glass.
  1. Remove drillings and pins from bottom of door.
Installation
  1. Snap plastic retainer and spacer into two glass retainer holes. Make certain that metal washer in the retainer assembly is on outboard side of glass.
  1. Insert glass into door.
  1. Position glass to glass bracket. Install two rivets to secure glass to glass bracket. NOTE: Two 1/4-inch-20 x 1-inch bolts and two 1/4-inch-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (36-61 lb-in). Equivalent metric retainers (6mm) may be used.
  1. Install door trim panel and watershield. Refer to Section 01-05.


2-Door Vehicles


n5878h.gif



4-Door Vehicles


n5879g.gif

May 29, 2009 | 1993 Ford Tempo

1 Answer

Drivers door window squeeks when it is opened.


before removing anything, try spraying some graphite spray down the side tracks of the door frame where the glass rolls up and down. do not spray the felts that go cross ways

Apr 26, 2009 | 2005 GMC Sierra

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
1955 Morris Minor Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Morris Experts

old marine
old marine

Level 3 Expert

1975 Answers

David Harrelson
David Harrelson

Level 3 Expert

5316 Answers

Joe Grech

Level 1 Expert

28 Answers

Are you a Morris Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...