Question about 2000 Lexus RX 300

1 Answer

Ignition light does not go off

After turning off the engine and removed the key the ignition light refused to go off

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 128 Answers

Problem with ignition mechanism.... something got stuck, worn out there....
try to spray WD 40 inside and move key in keyhole few times....
if it persists you need to change it

Posted on Mar 27, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 Cadilac CTS we bought a replacement chip key which the Chev Olds dealer could not program I took the new key to a Cadilac dealer they told me the key is defective now the Chev dealer has...


Okay, to program a key you will need two keys that are already programmed, insert one key ignition turned on and engine off, remove the key and within 10 sec insert the second key and turn ignition on with engine off, remove that key and within 10 sec insert the key to be programed. you will need to do a 30 min.relearn with only one key,you will turn ignition on with engine off and wait about 10 min until light goes out then remove the key and repeat this step when light goes out repeat step one more time then use key to start car, computer has learned all info. you will now turn off engine, insert programmed key turn key on engine off then remove the key and insert key to be programed within 10 sec.all done good day.

May 27, 2011 | 2004 Cadillac CTS

2 Answers

I have a new key cut and the security comes on. What can I do?


If your old key has a chip in it,then the dealer ship will have to code it.If not,try relearning the key to the ignition,turn the key on,leave it on 10 minutes,then turn it off,and right back on,do this three times,a total of thirty minutes,if this was at all helpful,please rate,thank you.

Aug 21, 2010 | 2000 Chevrolet Venture

2 Answers

My mechanics say the brain box locked on security. it has refused to start, they've tried all they can but it just wont start, they say the brain box has to be reprogrammed. it a nissan maxima 2000 model....


IF YOU GOT 2 SETS OF KEYS TRY ANOTHER IGNITION KEY.THAT NOT WORN.TURN ON IGNITION FOR 5 SECONDS.SWITCH THE IGNITION OFF.WAIT APPROXIMATELY 5 SECONDS.SWITCH IGNITION ON FOR APPROXIMATELY 5 SECONDS.SWITCH IGNITION OFF.WAIT APPROXIMATELY 5 SECONDS.START ENGINE.IF STARTS OTHER KEY WAS WORN.IF CAR STILL DONT CRANK.THE DEALERSHIP HAS REPLACE KEYS AND ANTI THEFT SYSTEM AND REPROGRAM TO CRANK.ALSO CHECK TO MAKE SURE THE NEUTRAL START BACK UP LIGHT SWITCH IS WORKING.IF FAULTY IT WILL ALSO CAUSE NO START PROBLEMS.

Feb 28, 2010 | 2000 Nissan Maxima

2 Answers

1996 Oldsmobile Achieva: Security light flashes upon startup


Here is what you do, but only when the SECURITY light flashes - if it is always ON or OFF it's no use.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes ( SECURITY light will flash for 10 minutes and then stay on SOLID)
Turn the key to OFF
Wait 5 seconds.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes.
Turn the key to OFF
Wait 5 seconds.
Turn the key in the ignition to ON.
Wait for exactly 10 minutes.
Turn the ignition OFF.

Start the car normally.
It has relearnt the keycode and you're good to go.
NOTICE - it takes 30 minutes to relearn, that's THREE cycles of ON - 10 minutes - OFF.

Good luck.

Jul 11, 2009 | 1996 Oldsmobile Achieva

1 Answer

2003 Prius sometimes will not start, engine light comes on. Removing key from ignition, reinserting key, & turning wheel till it locks will then allow the car to start. Engine light stays on for a


I had a wire connector on the front of the engine that had so much tension, the wires broke. I didn't notice until a wet day when the car wouldn't start (and the Check Engine light was on). (The error code was related to an Emissions error.) The connector is located on the engine, front, just left of center. Hope this helps!

May 25, 2009 | 2002 Toyota Prius

1 Answer

Key wont turn to Ignition point


you need to buy a new ignition tumbler

Dec 14, 2008 | 2000 Volvo S40

1 Answer

Ignition key wont turn


need to charge the battery. if i remember right its in the trunk or under the rear passenger seat

Oct 02, 2008 | 2004 Mercedes-Benz Mercedes Benz E Class

2 Answers

1996 honda odyssey


We found our solution...a new ignition. :-( One day the key stuck in the ignition and refused to be removed! It cost us around $350.00 to have a new ignition installed. No way around it.

Sep 29, 2008 | 1996 Honda Odyssey

1 Answer

I lost my key and the ford dealership by my house sad i need to reprogram a chip but the car is a 1999 tuaruse and its to old to pull up what can i do


Here is the factory procedure to program a new key(s), I recomment only factory keys, you need to use the working key to do the procedure;
1. Insert a previously programmed coded key into the ignition.

2. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4(ON) position for at least one second, but no more than 10 seconds.

3. Turn the ignition to the 3 (OFF) position, and remove the coded key
from the ignition.

4. Within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition.

5. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second but not more than 10 seconds.

6. Turn the ignition to the 3 (OFF) position, and remove the second key from the ignition.

7. Within twenty seconds of removing the previously programmed coded key, insert the unprogrammed key (new/valet key) into the ignition.

8. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second.

9. Your new unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and
then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off rapidly. If failure repeats, bring your vehicle to your dealer to have the
new key(s) programmed.

To program additional new unprogrammed key(s), repeat this procedure
from step 1 for each additional key

Jul 25, 2008 | Ford Taurus Cars & Trucks

Not finding what you are looking for?
2000 Lexus RX 300 Logo

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

881 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...