Question about 2005 Hyundai Tucson

1 Answer

The arm that drives the motor keeps popping off, what part do I need to fix it

My wipers are not working because the arm that drives the motor keeps popping off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 3,679 Answers

I would think you will need to replace the wiper linkage from moter as sounds likely the threads have been stripped or worst case wiper motor as well

Posted on Mar 27, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2003 Chevy cavalier and the wiper blades don't move but I see and hear the motor turning. What could be wrong with it and how can I fix it myself.


Take the wiper arm and try to move it if it's easy to move then ....we call it the transmission between wiper arm and motor itself. little teeths are gone wiper arm side or transmission

or transmission arms are disconnected

hope it help

Mar 04, 2015 | 2003 Chevrolet Cavalier

1 Answer

Engine schematics 2002 pontiac montana


Hi there:
Isnt a diagram but If you have removed the motor, here is the motor installation procedure....

INSTALLATION PROCEDURE

6_23_2012_11_48_33_pm.gif

Align the wiper motor to the wiper drive system module. NOTE: Refer to Fastener Notice in Service Precautions.
Install the wiper drive system module to wiper motor screws. Tighten Tighten the wiper drive system module to wiper motor screws to 7 N.m (62 lb in) .
Connect the electrical connector to the wiper motor.
Install the crank arm on the wiper motor.


6_23_2012_11_49_39_pm.gif

Rotate the washer solvent container into the installation position.
Install the washer solvent container screws. Tighten Tighten the washer solvent container screws to 6 N.m (53 lb in) .
Inspect the wipers for proper operation.


6_23_2012_11_51_04_pm.gif

Also, here is the crank arm procedure...

REMOVAL PROCEDURE

Remove the wiper system module cover.
Remove the drive link from the wiper motor crank arm.

2.1. Loosen the drive link screws.
2.2. Remove the drive link from the wiper motor crank arm.

Remove the wiper motor crank arm cover and seal.
Remove the wiper motor crank arm from the wiper motor.

4.1. Loosen the wiper motor crank arm screw.
4.2. Tap on the wiper motor crank arm screw with a soft-faced mallet while holding up on the wiper motor crank arm until the wiper motor crank arm loosens from the wiper motor.
4.3. Remove the wiper motor crank arm screw and the wiper motor crank arm from the wiper motor.

INSTALLATION PROCEDURE


6_23_2012_11_52_10_pm.gif

Install the wiper motor crank arm onto the wiper motor.

1.1. Turn the ignition switch to the ACCY position.
1.2. Set the wiper switch to PULSE position. The wiper motor should be operating.
1.3. Turn the ignition switch to OFF when the wiper motor is in the innerwipe position.

IMPORTANT: Do not rotate the wiper motor shaft during the installation of the wiper motor crank arm.

1.4. Install the wiper motor crank arm on the wiper motor while maintaining a 4-8 mm (0.157-0.315 in) gap between the V-grove in the wiper motor crank arm and the tab.

NOTE: Refer to Fastener Notice in Service Precautions.

Install the wiper motor crank arm screw. Tighten Tighten the wiper motor crank arm screw to 16 N.m (12 lb ft) .
Install the wiper motor crank arm cover and seal.


6_23_2012_11_52_52_pm.gif

Check the gap between the wiper motor crank arm and tab. If the gap is not 4-8 mm (0.157-0.315 in) , remove the wiper motor crank arm and repeat installation steps.
Install the drive link onto the wiper motor crank arm.
Install the drive link screws. Tighten Tighten the drive link screws to 5 N.m (44 lb in) .
Install the wiper system module cover.
Inspect the wipers for proper operation.

Additional procedures: Wiper Motor Module Replacement.

TOOLS REQUIRED
J 39822 Wiper Arm Puller

REMOVAL PROCEDURE

Turn the ignition switch to the ACCY position.
Set wiper switch to the PULSE position.
Turn the ignition off when the wiper arms are in the innerwipe position and not moving.
Disconnect the washer hose from the washer nozzle.
Remove the cover from the wiper arm nut.
Remove the wiper arm nut from the wiper transmission drive shaft.
Using J 39822 remove the wiper arm from the wiper transmission.
Remove the wiper blade from the wiper arm.
Clean the knurls of the wiper transmission drive shaft with a wire brush.



Install the wiper blade onto the wiper arm.
Install the wiper arm onto the wiper transmission drive shaft. IMPORTANT: Hold the measuring device at 90 degrees (perpendicular) to the wiper blade tip.
Measure the distance from the wiper blade tip to the solid edge of the windshield blackout. Position the wiper arms at the following distances:

LH - 147 mm (5.79 in) above the glass blackout.
RH - 123 mm (4.84 in) below the glass blackout.

NOTE: Refer to Fastener Notice in Service Precautions.



Install the wiper arm nut onto the wiper transmission drive shaft. Tighten Tighten the wiper arm nut to 48 N.m (35 lb ft) .
Install the cover on the wiper arm nut. IMPORTANT: Lubricate the washer hose with the windshield washer solvent to ease installation on the washer nozzle.
Install the washer hose on the washer nozzle.
Inspect the wipers for proper operation.



Remove the wiper arms from the vehicle.
Remove the air inlet grille panel.
Remove the wiper motor.
Remove the air inlet panel to wiper motor module screws.
Remove the wiper motor module from the vehicle.
Remove the insulators from the wiper motor module.

INSTALLATION PROCEDURE

Install the insulators onto the wiper motor module.
Align the wiper motor module to the air inlet panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the air inlet panel to wiper motor module screws. Tighten Tighten the air inlet panel to wiper motor module screws to 10 N.m (89 lb in) .
Install the wiper motor.
Install the air inlet grille panel.
Install the wiper arms onto the vehicle.
Inspect the wipers for proper operation.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 2002 Pontiac Montana

2 Answers

My windshield wipers will not work but i hear the motor trying to work. what does this mean? are they totally broke or is there a simple fix?


Sounds like the link rod has popped off or the wiper arm nuts need tightened. When the wipers freeze to the windshield and you start the wipers to clear the snow this will either strip out the wiper arms or pop the linkage rod off. Always pull the wipers away from the windshield before you start the wiper motor in cold weather to be sure they are not frozen to the windshield. Ok how to repair. Grab the wiper arms and see if they freely move in thier normal pattern with power off. Do they move independantly of each other ? If your lucky the nut holding the arms to the pivot just needs tightened. At the base of each arm is a black cover you have to pry up th see the nut. If not remove the wiper arms and inspect to see if they are stripped out. If they are stripped out bad enough you may have to replace them. If not then the linkage has popped off beneath the drainage grill. To see the link rods move look down thru the grill with the wiper motor running and the wiper arms off and you may see the rod flopping around. Now pry the plastic grills off, with the power off, left side first to get to the rod. Look to see if the plastic retainer in the end that fell off is still ok if so just line it up and give it a smack to pop it back on to the ball stud. If the shaft that is installed onto the motor is spinning but not moving the rod the motor must be replaced. Oopen hood and remove three bolts holding the motor to the firewall to remove it. Just reverse the process to reinstall. Thanks for asking at Fixya.com.

Dec 20, 2010 | 1998 Ford Expedition

3 Answers

The wipers are stuck in the up position when they are turned off. the work ok but will not nest when turned off


This is a very common problem on the Impalas. I had to fix my 2002 Impala. The wipers will point straight up.
There is a tab that may be bent near the wiper motor shaft.
Open the hood.
You need to remove the driver's side wiper arm. You need to pop-off the round black cover and there's a nut underneath.
Then remove the plastic cover between the windshield and the engine compartment.
See the pictures below, Look for a bent TAB. it's tough, but bend it back with pliers and/or big screwdriver.
If the tab is OK, look for a missing or broken spring. For that, you'll need to get the replacement part from the dealer. May be: park mechanism, part #12494832
zeevert_22.jpg
zeevert_23.jpg
zeevert_24.jpg
I did a full write-up at this website: www.naioa.com
http://www.naioa.com/v2/modules.php?name=Forums&file=viewtopic&t=26086
You may have to register for free, and look under the "knowledge Based" section in the Forum.

Dec 09, 2010 | 2002 Chevrolet Impala

1 Answer

Windshield wipers do not work-- switch works and it sounds as if the motor is working. Suggestions?


Hi

Under the Skuttle panel is where the motor is located, the main motor has 2 arms coming off it, these work on a ball joint type set up kind of a knee joint if you like. basically the joint can pop off and thus causing the wipers to not work but you still hear the motor, the other thing is the arm could have snapped inside, the knuckle joint though should just pop back on, if it keeps coming off then it is simply worn, its a cheap fix though and common sense once you can see the motoe straight forward job. If you need any thing further get back to me
Regards
Dan, p.s the skuttle panel is directly below the windsheild, normall a black panel but not always.

Nov 18, 2010 | 1993 Ford F150 SuperCab

1 Answer

Window wipers not working although its motor is


sounds as if the wiper arm to the motor has come undone and removal of the panel on the firewall needs to be removed in order to reattach the arm ..this happens from either wear or when heavy snow and ice prevent the wipers from working and from the force of the motor will cause it to pop ...fairly easy to do simply open the hood and remove the screws to the panel ..locate the wiper motor and you will see the panel which covers the wiper apparatus remove it and after the wipe armature is located you may need to turn the key on and shut the wipers to Off position and then turn off the key before reattaching the arm ...reverse procedure is how to reinstall the panel ...

on another note are you sure the wipers themselves are not stripped out the spline drive to the wiper or that they are properly seated as well ..that would be my 2nd thought

Jan 01, 2010 | 2001 Daewoo Lanos

2 Answers

Wiper motor replacement for a 99 crown vic


I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

May 06, 2009 | 1999 Ford Crown Victoria

2 Answers

Pass side wiper not working on 2002 volvo s40


Ok, this is a bad motor and you will have to replace this failed motor. this will fix the issue.


Apr 22, 2009 | 2002 Volvo S40

1 Answer

1994 lincoln clip that attaches mortor to wiper arm keeps popping


Make sure the wipers are in the parked position - fully at the bottom of their travel. Haynes guide says to then put a wrench on the motor drive crank and a wrench on the bolt to get the bolt off

Jan 04, 2009 | 1984 Volvo GL

Not finding what you are looking for?
2005 Hyundai Tucson Logo

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...