Question about Subaru Outback

1 Answer

Brake indicator light, battery indicator light, and loss of power steering

Lights illuminated at the same time as loss of power steering. noticed a ticking sound while engine running

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Check belts

Posted on Jun 05, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: the check engine light illuminates,

HI...
THis problem is caused for
Lost of correlation between ACELERATOR PEDAL POSITION
AND THROTTLE ACTUATOR MOTOR.
Because your car has no acelerator cable.
The morer probable is the Trhottle actuator motor come damaged. 90%. 10% the accelerator pedal position.
If you turn of the car it will work OK> for a few time.
But the Service engine soon. will stay on.
Yuo can go to at ANy ADVANCE AUTOPART, AUTOZONE or NAPA AUTOPART. They make a diagnostic free.
If not. I recomend get the car scanned for see exactly why the light come on. and make the right repair procedure.

OK>> I hope this help on your question...

Thank you for use fixya.

Posted on Jul 25, 2008

pal03246
  • 726 Answers

SOURCE: brake and battery light on

Alternator failure

Posted on Jul 17, 2008

SOURCE: 1999 Ford F150, Charging system.

Your battery may not be holding its charge. Charge the battery and take a voltage reading. Then after a few hours take another reading andsee if the voltage has dropped. If that is alright, refit the battery to the car. turn off all the electrics anddo a voltage test. If the battery is discharging then ou will have to find what componant is drawing the voltage. I normally check the boot through the rear seats first.

Posted on Nov 28, 2008

pippall
  • 1486 Answers

SOURCE: Check engine light and power loss

Air flow meter sounds like your problem.

Posted on May 27, 2009

  • 104 Answers

SOURCE: loss of power steering,battery light

Check for bad alternator or wiring to alternator. Also replace battery if its old, as it puts extra strain on alternator. Check also that the belt didnt come off, if this is the case, check all pulleys on motor to see if one seized up and needs replaced with belt.

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When you power off the unit, it goes from bright led to low light led and shows a red light staying illuminated. Which means its STILL drawing battery. How do you turn it off completely?


Brake Hydraulic System Red Warning Light - RepairPal

repairpal.com/brake-hydraulic-system-red-warning-light
If the brake hydraulic system red warning light comes on and stays on, this indicates... and seems to come on and off depending on whether the vehicle is turning, ... if it is discovered that the light was illuminating due to a low brake fluid level.

Sep 10, 2015 | Cars & Trucks

2 Answers

Battery and break indicator showed up and power steering went out all at the same time


Are you sure the drive belt is still on the engine ?
The battery light usually comes on when the alternator is not charging the battery, and the power steering is also belt driven.
The brake warning light can come on when the brake fluid is low, but also when the battery light comes on.

Jul 24, 2012 | 1995 Isuzu Rodeo

1 Answer

How to reset stabilitrak on a 2007 chevy equinox


Your vehicle has electric power steering !
The Electric Power Steering (EPS) system reduces the amount of effort needed to steer the vehicle. The system uses the power steering control module (PSCM), torque sensor, power steering motor rotational sensor, power steering motor, discrete battery voltage supply circuit, and the GMLAN serial data circuit to perform the system functions. The PSCM and power steering motor are each serviced separately from the steering column assembly. However, the motor rotational sensor is serviced as part of the power steering motor, and the torque sensor is serviced as part of the steering column assembly. The PSCM also monitors vehicle speed from the engine control module (ECM) via the GMLAN serial data circuit. At low speeds more assist is provided for easy turning during parking maneuvers. At higher speeds less assist is provided for improved road feel and directional stability.
Stability System Indicator The IPC illuminates the stability system caution indicator when one or more of the following conditions exists. The EBCM sets any one of many VSES-disabling DTCs. The EBCM sends a serial data message to the IPC requesting illumination.
Traction Control System Indicator
TRAC OFF The instrument panel cluster (IPC) illuminates the TRAC OFF indicator when the following occurs:
?€¢
The electronic brake control module (EBCM) inhibits the traction control system due to a malfunction in the traction control system. The IPC receives a serial data message from the EBCM requesting illumination.


?€¢
The Body Control module (BCM) detects that the traction control switch has been pressed (signal circuit is low). The Body Control module (BCM) sends a serial data message to the EBCM in order to disable traction control. The IPC receives a serial data message from the EBCM requesting illumination. The BCM sends a serial data message to the radio in order to activate an audible warning.


Your best bet is to take it to a ASE certified an qualified repair shop ,that has the diagnostic tool to fix this problem .

Jun 17, 2012 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Warning lights remain illuminated, Alero


does the anti-lock brake light come on too? and ive found the best way to reset codes manually is disconnect the battery terminals pos. and ground. then touch them together( the battery cable terminals) their is a copasitor that will store enough power to hold your codes in the ecm. this way you are essentially grounding the system to drain all residual power stores

Feb 09, 2012 | 2000 Oldsmobile Alero

1 Answer

2007 BMW 525i warning light (red) looks like a steering wheel with a lock attached car not starting


Its the "EML" warning light in a BMW indicates a problem with the "drive by wire" throttle control system."

That red light indicates u have loss BRAKE FLUiD in ur system and needs to TOP UP the brake master. It also indicates s pressure loss in the brake system and u have to check the FLUiD, LEAK and ur BRAKE PADS!

Check all of these and tell us wut happened!


Nov 16, 2010 | 2007 BMW 335i Coupe

1 Answer

Loss of power steering and battery light and emergency brake lights come on when driving my 2003 santa fe in the rain


2055 Santa Fe. Drove fine, parked for a few hours, battery light on and parking light on, no power steering. Help?

Dec 10, 2009 | Hyundai Santa Fe Cars & Trucks

2 Answers

2004 A4 1.8T Brake Lights Remain On After Car Is Parked


Sounds like your brake light switch is on its way out. Its a simple fix and a cheap part. It will need to be done immediately as not only can the lights staying on drain your battery but it can also cause lack of power and not put the brake lights on when braking. The switch is operated by the pedal itself and requires the drivers underdash trim to be removed. With this off the switch can be accessed and replaced. If you can get a vehicle technician to fit it, do so, as they are quite fragile and new switches can become useless if fitted incorrectly. Good luck

Feb 07, 2009 | 2004 Audi A4

2 Answers

I have a 2003 GMC Savana Van. The brake light came on and the brake alarm rings continously but will stop if I hit a bump (and then start again if I hit another one). I'm thinking a loose wire but several...


If someone took the time to look at the electrical schematic you will see several grounds in the circuit My first place I would go would be to check all the Grounds and Connections for the Brake Fluid level control, Brake Warning Indicator
The Instrument Panel Cluster (IPC) illuminates the brake warning indicator when one or more of the following occurs:
  • The body control module (BCM) detects that the park brake is engaged. The IPC receives a class 2 message from the BCM requesting illumination.
  • The electronic brake control module (EBCM) detects a low brake fluid condition. The IPC receives a class 2 message from the EBCM requesting illumination.
  • The electronic brake control module (EBCM) detects a closed brake pressure differential switch. The IPC receives a class 2 message from the EBCM requesting illumination.
  • The EBCM detects an ABS malfunction which disables dynamic rear proportioning (DRP) . The IPC receives a class 2 message from the EBCM requesting illumination.
  • The IPC detects a closed power brake booster alarm switch and closed power brake booster fluid flow alarm switch. The IPC illuminates the brake warning indicator and sends a class 2 message to the radio requesting the brake warning alarm.
  • The IPC performs the bulb check at the start of each ignition cycle. The brake warning indicator illuminates for approximately 3 seconds before turning OFF.
  • The IPC detects a loss of class 2 communications with the BCM or with the EBCM.
Driver Information Indicators and Messages
The following indicators are used to inform the driver of several different factors.

Brake Warning Indicator
The Instrument Panel Cluster (IPC) illuminates the brake warning indicator when the following occurs.
  • The Body Control Module (BCM) detects that the park brake is engaged. The IPC receives a serial data message from the BCM requesting illumination. The brake warning indicator flashes at a rate of approximately twice per second when the park brake is engaged.
  • The EBCM detects a low brake fluid condition or base brake pressure differential and sends a serial data message to the IPC requesting illumination.
  • The IPC performs the bulb check.
  • The EBCM detects an ABS-disabling malfunction which also disables Dynamic Rear Proportioning (DRP) and sends a serial data message to the IPC requesting illumination.

Here is a description of how the system works But i would check my Grounds and connections
www.aceautomotive1.com
Contact me if you need any more information Ill be glad to help

Aug 01, 2008 | GMC Savana Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...