Question about 2003 Ford Explorer

Open Question

C1165 abs light coming on. tested but has code c1165 & c1175

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me what c1165 and c1175 mean on a toyota avalon


Nicole, They are chassis codes, may depend on the year but this is what I came up with.
C1165: Speed Wheel Sensor RR Input Circuit Failure
C1175: Speed Wheel Sensor LR Input Circuit Failure

Apr 09, 2016 | Toyota Cars & Trucks

1 Answer

My car failed inspection for codes P-1000 and C-1175


p1000 is a generic code and is always present, c1175 is a problem with the abs system.

Oct 13, 2015 | 2002 Jaguar X-Type

1 Answer

X-type se 3.0 2001 codes c1165-c1175 what are they


Speed sensors on wheels. Have you had any service to tires or wheels?

These hall effect sensors are at the inside diameter of your wheels and tell the computer the wheel is turning. one at each wheel are common now on all wheel drive autos. there is a small plug on these sensors that can become unplugged by running over something maybe....
More than likely a wheel bearing is failing causing heat to the sensor mounted in the bearing causing the sensor to fail.

Feb 28, 2015 | 2002 Jaguar X-Type

1 Answer

2003 jaguar s type code p1000 and c1165


the p1000 is a system readiness code meaning the car is checking itself..it means its not finished etc but once it has the code will change to p1111..meaning system check completed, the c1165 is a abs or wheel speed code, check the wheel where this code is originating

Apr 03, 2014 | 2003 Jaguar S-Type

1 Answer

2006 ford crown vic abs code b1596


B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .

Jan 14, 2013 | 2006 Ford Crown Victoria

1 Answer

Abs fault light, engine management light, parkbrake fault (won't go off) DSC fault light, air suspension fault, 2003 Jaguar 3.5 SC V8, ah also discovered water ingress in boot, quite a lot!!, only fault...


try disconnecting the battery both leads and join them together for 5 mins and see what happens cannot find this fault code in teh jaguar OBD codes so consult with teh code reader manufacturers

Feb 08, 2011 | 2003 Jaguar XJ-Series

1 Answer

What is service codes P1111, C1145, C1155, C1165, C1175?


HI. The codes and their respective definitions are below:


P1111 Intake Air Temperature (IAT) Sensor Circuit Intermittent High Voltage
C1145 Front right wheel speed sensor input circuit failure
C1155 Front left wheel speed sensor input circuit failure\
C1165 Rear right sensor - trigger monitoring
C1175 Rear left sensor - trigger monitoring

Aug 12, 2010 | 2002 Jaguar X-Type

1 Answer

I have p1000 and c1175 codes


P0128 is a Coolant Thermostat Malfunction

P1000 shows that the fault code has been reset recently (but this code will not bring the warning light on)

C1175 I think is Speed Wheel Sensor LR Input Circuit Failure or Input circuit failure and could be directly related to your ABS fault light indication.

Jan 27, 2010 | 2003 Jaguar X-Type

1 Answer

Can you tell me what these two codes are P1000 and a C1165 on jaguar x type 3 litre abs, thanks


Po code 1000 is system readyness test, it means it has not met all condtions or flags since last reset of the computer. and the other C1165-Wheel speed sensor circuit right rear electrical failure and C1235-Wheel speed sensor circuit right rear signal failure
Possible Source(s):
  • Harness fault.
  • Connector loose or corroded.
  • Connector pin(s) bent or tracking between connections.
  • Sensor gap incorrect.
  • Foreign matter on sensor face.
  • Missing tooth on sensor wheel.
  • Faulty Sensor.
  • Most Likey cause the harness got knocked off the sensor. If you need more help let me know.

Sep 21, 2009 | 2002 Jaguar X-Type

1 Answer

Have error codes C1175 & P1000 for a 2002 Jaguar X-type 2.5.


C1175 ABS/TCCM Anti-lock braking / traction control LH rear wheel speed sensor circuit fault ABS/TCCM to wheel speed sensor signal circuit (FH33-21): open circuit, short circuit to ground, short circuit to B+ voltage, high resistance LH rear wheel speed sensor failure
P1000 is for check not complete after last memory clear , dont worry about it , just stick with C1175 , and most probably it is the sensor wire

Jul 25, 2009 | 2002 Jaguar S-Type

Not finding what you are looking for?
2003 Ford Explorer Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...