Question about 1991 Ford F250

Open Question

Ford engine codes

Engine code is 37 and 35

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix error code C1211. My make and model is the 1996 Ford Econoline E-250, 4.9L engine.


I can not find a C1211 Ford error code. I did find a
P1211 Injector Control Pressure Sensor Above / Below Desired
Error code for Ford. https://www.engine-light-help.com/ford-check-engine-light.html
A Generic C1211 OBD2 error code specifically refers to the camshaft (cam) timing.
http://c1211.engineerrorcode.com/

Nov 16, 2016 | Ford Cars & Trucks

1 Answer

2005 Ford Freester engine running but will not drive code P1000


P1000 fault code is a misnomer because it is not really a fault code. When this code is flashed in your dash panel, it just shows that the reset cycle of your engine computer is not completed yet. Normally, if you are resetting the code, you would disconnect the battery (-) terminal for 1 minute and reconnect. However, on some engines like Ford, the previous code is not totally erased yet so that this P1000 code will show up.

Nov 08, 2016 | Ford Cars & Trucks

1 Answer

Ive got a 93 ford ranger.after it gets warm & u cut it off for about 5 mins,& start it back its like it floods


Ford Check Engine light Codes - FreeAutoMechanic

www.freeautomechanic.com/diagnostictroblecodes7.html
Full list of OBD I Diagnostic Trouble Codes for your Ford Vehicle. If your Check engine light is on you may have a serious problem. Scan your codes and follow ...

EEC-IV 2 and 3 digit trouble codes. - Ford Explorer and Ranger ...

www.explorerforum.com > ... > EEC IV
Feb 6, 2007 - Serious Explorations Ford Explorer and Ranger Message Board .... 3.8L AXOD - Message center data link circuit fault - See code 70 73 (O) Is FORD DEALER the only place who can read out ABS error ...
Dec 5, 2011
Error codes 186 & 539.
Aug 15, 2009
OBD-II Diagnostic Trouble Codes (DTCs)
Nov 8, 2008
Have a Code? OBD II Trouble Codes Here
Jan 19, 2006
More results from www.explorerforum.com

EEC-IV Diagnostic Trouble Codes - Diagnose problems in


Dec 19, 2015 | 1988 Ford Ranger

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

Ford F140 4.2 Do Engine codes P0305, P0306, and P1518 relate to each other


I am assuming you mean F150 truck.
The answer is maybe.
Code 305 and 306 are missfire codes for cylinders 5 and 6.
Code 1518 is for a problem with the intake manifold runner control which could cause the other two codes.

P1518 FORD Description The Intake Manifold Runner Control (IMRC) is monitored for failure during continuous or key ON engine OFF self-test.
Possible causes - Intake Manifold Runner Control (IMRC) harness is open or shorted
- Intake Manifold Runner Control (IMRC) circuit poor electrical connection
- Faulty Intake Manifold Runner Control (IMRC) actuator
- Faulty Engine Control Module (ECM)
Read more: http://engine-codes.com/p1518_ford.html#ixzz2KSN6Thui

Feb 10, 2013 | Ford Cars & Trucks

1 Answer

Ford expedition 2007 engine crank but wont start and engine light blinking 8 times


Check engine light blinking,this is indication of error code stored in the Engine control module.its advisable to get vehicle scanned at diagnostic center to retrieve the error code stored.Once the error codes are retrieved,further diagnosis can be done as per error code.

But if all this basics are checked ok,then for most common possibility and further troubleshooting of this problem,click the link below:-----
http://technoanswers.blogspot.com/2012/10/2007-ford-expedition-engine-cranks-but.html
------------
Ford Expedition FREE Repair Guide? http://technoanswers.blogspot.in/2012/03/ford-expedition-and-lincoln-navigator.html
----------
This details will help.
Thanks.

Oct 06, 2012 | 2007 Ford Expedition Eddie Bauer EL

1 Answer

How to read engine cose 1990 ford escort 1.9


On board diagnostic (OBD) was designed on vehicles equipped with electronic fuel injection so you can generally retrieve the codes yourself. No need buying a scanner or running to any parts stores to check the engine light. This system is called obd1 and applies to most vehicles made before 1995 for domestics and 1993 on imports.
Ford owners can check their check engine light using the diagnostic connector located at the engine compartment by the fender near the battery. Getting the obd1 codes need a couple of tools: a 4 inch long gage 16 jumper wire and a 12 volt test light. Both tools are hooked up to the diagnostic connector and when the IGNITION KEY is turned on (without starting engine) the codes will begin to flash in the test light, not in the dash panel. If there is no code, you will normally get code 11 or 111. On Fords, there are 2 test modes, the KOEO (key on engine off) and the KOER (key on engine running). Both test modes should be used to get the accurate evaluation of the stored fault codes.
Most of the codes can be erased or cleared by disconnecting the battery negative terminal for 1 minute and reconnect. Just make sure to check your service manual in case you have electronic equipment such as radio or clock that needs reprogramming in which battery disconnection is not recommended. Finally after performing repairs on the culprit code, always go for a road test to confirm if the problem is fixed.
http://www.troublecodes.net/Ford/88-951325.shtml

Nov 02, 2009 | 1990 Ford Escort

1 Answer

My 2004 freestar has an engine code 1235. I can


It may be a code peculiar to Ford. You may need to check with a Ford dealer service department. Better code scanners reveal what the code refers to. Check with some place like Autozone??

Aug 17, 2009 | 2004 Ford Freestar

Not finding what you are looking for?
1991 Ford F250 Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...