Question about 1992 Toyota Camry V6

1 Answer

Water inlet is the o ring flat

O ring will not go into houseing

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

You have to see if its flat or round check the old and than apply which ever ones ok

Posted on May 20, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change waterpump on 91 lexus ls 400


DRAIN COOLANT SYSTEM.DISCONNECT THE RADIATOR INLET HOSE FROM INLET PIPE. REMOVE THE TIMING BELT FROM THE WATER PUMP PULLEY. REMOVE THE RIGHT SIDE IGNITION COIL.REMOVE THE WATER INLET HOUSING AND THERMOSTAT.REMOVE THE MOUNTING BOLTS AND STUDS. LIFT OUT THE WATER PUMP BY CAREFULLY PRYING BETWEEN THE PUMP AND THE CYLINDER HEAD. REMOVE ALL THE OLD PACKING AND CLEAN THE MOUNTING SURFACES. INSTALL NEW SEAL PACKING TO THE WATER PUMP GROOVE AND A NEW O - RING TO THE WATER BYPASS PIPE.INSTALL THE TIMING BELT AND CONNECT THE INLET HOSE TO THE INLET PIPE.THEN REFILL THE COOLING SYSTEM. RUN THE ENGINE CHECK FOR LEAKS.

Sep 03, 2011 | Lexus LS 400 Cars & Trucks

1 Answer

How do you replace a thermostat


WARNING: SCALDING HOT COOLANT, WATER OR STEAM
NEVER remove the pressure relief cap under any conditions while the engine is operating. Failure to follow these instruction could result in DAMAGE to the
cooling system or engine AND/OR personal injury. To avoid having scalding hot coolant or steam blow out of the cooling system or reservoir, use extreme care when removing the pressure relief cap from a hot cooling system or reservoir.
  1. Wait until the engine has cooled.
  2. Wrap a thick cloth around the pressure relief cap and turn it slowly (until the pressure begins to release.
  3. Step back while the pressure is released from the cooling system.
  4. When you are certain all the pressure has been released, (still with a cloth) turn and remove pressure relief cap .
REMOVAL

  1. Drain the engine cooling system so that the engine coolant level is below the water thermostat (8575).
  2. Raise vehicle on hoist. See General Information.
  3. Disconnect the lower radiator hose (8286) and degas bottle hose from the water inlet connection.
  4. Remove the two water inlet connection retaining bolts. Remove the water inlet connection.
  5. Remove the O-ring seal and water thermostat from the water thermostat housing. Inspect O-ring for damage and replace if necessary.
  6. If required, remove water bypass hose from water thermostat housing and remove water thermostat housing retaining bolts, water thermostat housing and O-ring from oil filter adapter (6881). Inspect O-ring for damage and replace if necessary.
INSTALLATION
  1. Install the water thermostat, O-rings, water thermostat housing (if removed) and water inlet connection as illustrated.
  2. Install and alternately tighten the retaining bolts. Tighten bolts to 20-30 Nm (15-22 ft. lbs.).
  3. If removed, connect the water bypass hose to the water thermostat housing.
  4. Connect the lower radiator hose and degas bottle hose to the water inlet connection.
  5. Lower vehicle.
  6. Fill the coolant with Ford Premium Cooling System Fluid E2FZ-19549-AA or-B (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-8-B) or equivalent that meets Ford specification ESE-M97B44-A in a 50/50 mixture with water.
  7. Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
  8. Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.

Jan 10, 2011 | 1997 Lincoln Continental

1 Answer

Water pump location


Here are the procedures.

WATER PUMP
Removal

1. Drain cooling system. Remove timing belt. Remove right ignition coil. Disconnect coolant hose from coolant inlet housing.

2. Remove retaining bolts and separate coolant inlet housing and "O" ring from water pump. Remove retaining bolts/nuts and water pump. Remove "O" ring from coolant by-pass pipe which fits into rear of water pump.


Installation
Ensure sealing surfaces are clean. Install NEW "O" ring on coolant by-pass pipe. Lubricate "O" ring with soapy water solution.

2. Apply a .08-.12" (2.0-3.0 mm) diameter bead of sealant on mounting surface at rear of water pump. Install water pump. Ensuring water pump engages over coolant by-pass pipe. Tighten
fasteners to specification.
See

3. To install remaining components, reverse removal procedure. Fill and bleed cooling system.

Jan 05, 2011 | 1992 Lexus Ls 400

1 Answer

2003 CHEVROLET SILVERADO 2500HD 6.0 - thermostat location and replacement


4.8L, 5.3L & 6.0L Engines
  1. Remove the air inlet duct.
  2. Drain the cooling system.
  3. Remove the radiator outlet hose.
  4. Remove the thermostat housing bolts.
  5. Remove the thermostat from the water pump housing.

The O-ring seal is integral to the thermostat housing



c17hydro_16.gif

Thermostat housing-4.8L, 5.3L and 6.0L engines


To install:

  1. Install the thermostat to the water pump housing making sure the spring side is inserted into the engine.
  2. Install the bolts.
    • Tighten the bolts to 11 ft. lbs. (15 Nm).
  3. Install the radiator outlet hose.
  4. Fill the cooling system.
  5. Install the air inlet duct.
  6. Test the system for leaks.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 26; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

Nov 13, 2010 | 2003 Chevrolet Silverado 2500HD

1 Answer

I need to change my thermastat but can not locate it


REMOVAL & INSTALLATION (4 Cyl. eng.) CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Position a suitable drain pan under the radiator drain **** and drain the cooling system.
  2. On the 1MZ-FE engine, remove the air cleaner cap assembly. Be sure to label all wiring disconnected.
  3. Disconnect the water temperature switch harness from the water inlet housing (except 5S-FE engines).
  4. Remove the oil filter on 5S-FE engines. On the 1MZ-FE engines, remove the heater hose covering the housing.
  5. Loosen the hose clamp and disconnect the lower radiator hose from the water inlet housing.
  6. Remove the two nuts from the water inlet housing and remove the housing from the water pump studs.
  7. Remove the thermostat and rubber O-ring gasket from the water inlet housing. To install:
  8. Make sure all the gasket surfaces are clean. Clean the inside of the inlet housing and the radiator hose connection with a rag.
  9. Install the new rubber O-ring gasket onto the thermostat. On 2SE and 3S-FE engines, align the jiggle valve of the thermostat with the protrusion on the water inlet housing. On 5S-FE engines, align the jiggle valve with the upper side of the stud bolt. On 2VZ-FE and 3VZ-FE engines, align the jiggle valve with the stud bolt. Insert the thermostat into the housing. Fig. 1: Remove the thermostat housing from the engine with the coolant temperature sensor - 1MZ-FE engine 89553p18.jpg
    Fig. 2: Removing the thermostat from the engine - 1MZ-FE engine 89553p19.jpg
    Fig. 3: Always discard the old O-ring from the thermostat, if reusing the old component 89553p20.jpg
    Fig. 4: Always replace the thermostat with the correct temperature specifications 89553p21.jpg
    Fig. 5: Line-up the jiggle valve with the protrusion on the housing - 5S-FE engine 89553g10.gif

  10. Position the water inlet housing with the thermostat over the studs on the water pump and install the two nuts. Tighten the two nuts to 78 inch lbs. (9 Nm) on 4 cyl. engines, 2VZ-FE and 3VZ-FE; 14 ft. lbs. (20 Nm) and 69 inch lbs. (8 Nm) on 1MZ-FE engines. Fig. 6: Thermostat installation - 2VZ-FE and 3VZ-FE engines 89553g11.gif
    NOTE: Don't forget to install a new O-ring onto the water inlet pipe. Apply soapy water to the O-ring prior to installation.
  11. Connect the lower radiator hose to the inlet housing and install the hose clamp. On the 3VZ-FE, tighten the bolt holding the water inlet hose to the alternator belt adjusting bar to 14 ft. lbs. (20 Nm). On the 1MZ-FE engine, tighten the bolt retaining the water inlet pipe to the cylinder head to 14 ft. lbs. (20 Nm).
  12. Attach the water temperature switch connector.
  13. On the 1MZ-FE engines, install the heater hose removed.
  14. Install the oil filter and check the oil level if removed. Install the air cleaner cap assembly on the 1MZ-FE engines.
  15. Fill the cooling system with a good brand of ethylene glycol based coolant.
  16. Start the engine and inspect for leaks.
prev.gif next.gif

Oct 08, 2010 | 1990 Toyota Camry

2 Answers

How do i change a thermostat on a 1996 mercury sable and whre is it located


Thermostat-follow the upper radiator thick hose to the thermostatic housing. Removal & Installation 3.0L (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions in the beginning of this section.
  2. Drain the engine cooling system into a suitable container.
  3. Remove the three thermostat housing bolts.
  4. Remove the thermostat O-ring seal.
  5. Inspect and clean the sealing surfaces.
To Install:
  1. Install thermostat and o-ring seal.
  2. Install thermostat housing bolts; torque to 9 lb-ft (12 Nm).
  3. Refill cooling system.
  4. Warm-up vehicle and check for leaks.
  5. Top off cooling system.
3.0L (4V) To Remove:
  1. Drain the engine cooling system.
  2. Disconnect the lower radiator hose from the water inlet adapter.
  3. Remove the bolts, the water outlet adapter and thermostat. Discard the O-ring seal.
To Install:
  1. Clean the sealing surfaces.
  2. Install the thermostat with a new gasket. Tighten the bolts to 89 in-lb (10 Nm).
  3. Refill the cooling system.
  4. Warm-up the vehicle and check for leaks.
  5. Top off the cooling system.
3.4L (SHO) To Remove:
  1. Drain the engine cooling system.
  2. Remove battery.
  3. Remove power distribution box.
  4. Remove battery tray.
  5. Disconnect upper radiator hose and place it out of the way.
  6. Disconnect the lower radiator hose from the water inlet connection.
  7. Remove the two mounting bolts and remove the water inlet connection.
  8. Remove the O-ring seal and thermostat from the water pump.
  9. Inspect O-ring for damage and replace if necessary.
To Install:
  1. If necessary, install a new O-ring on the inlet connection.
  2. Install the thermostat in the water pump and install the inlet housing. Tighten the bolts to 71-106 lb-in (8-12 Nm).
  3. Connect the lower radiator hose to the water inlet connection.
  4. Install the upper radiator hose.
  5. Install battery tray.
  6. Install the power distribution box.
  7. Install the battery.
  8. Refill the engine with coolant.
  9. Start the engine and allow the engine to warm up so that the water thermostat opens. Check for leaks.
  10. Stop the engine. Allow the engine to cool and top off degas bottle as required to maintain minimum cold fill level.
prev.gif next.gif

Aug 03, 2010 | 1996 Mercury Sable

1 Answer

Which way does the themosat gasket go on a 1997 chevy s10 2.2


Thermostat If It's an O-ring it will go on either way and seal the thermostatic gasket. Removal & Installation 2.2L Engine To Remove:
  1. Drain the cooling system to a level below thermostat
  2. Remove or disconnect the following:
    • Radiator inlet hose clamp and hose
    • Water outlet housing mounting bolts and housing gm_truck_s10_tstat.gif

    • Thermostat and O-ring seal
To Install:
  1. Clean and inspect all parts for wear or damage
  2. Clean mating surfaces
  3. Install or connect the following:
    • Thermostat and the O-ring seal
    • Water outlet housing and bolts
      1. Torque to: 89 lb. in. (10 Nm)
    • Upper radiator inlet hose and clamp
  4. Fill with coolant
  5. Inspect for leaks

Jul 29, 2010 | 1997 Chevrolet S-10 Pickup

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

How do you replace a thermostat on a 2002 toyota celica


Toyota Celica, Corolla, ECHO & MR2 1999-05Toyota Celica, Corolla, ECHO & MR2 1999-05

2002 Toyota Celica 1.8L MFI DOHC 4cyl


The thermostat is located in the water inlet housing that is connected to the lower radiator hose.
The thermostat is equipped with a by-pass valve. If the engine tends to overheat, removal of the thermostat would cause a decrease in cooling system efficiency.

CAUTION NEVER drain coolant directly onto the ground! NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
d4c6b82.jpg

Fig. The oil filter must be removed to access the thermostat on the 5S-FE engine
  1. Position a suitable drain pan under the radiator drain **** and drain the cooling system.
  2. On the 7A-FE engine disconnect the engine coolant temperature switch harness from the water inlet housing.
de1afd5.jpg

Fig. Disconnect the engine coolant temperature switch wiring located on the side of the thermostat housing
  1. Remove the oil filter on 5S-FE engines.
  2. Loosen the hose clamp and disconnect the lower radiator hose from the water inlet housing.
d253a81.jpg

Fig. Loosen the radiator hose clamp ...

5746ade.jpg

Fig. ... then slide the hose off the thermostat housing
  1. Remove the two nuts from the water inlet housing and remove the housing from the water pump studs.
f78b0a7.jpg

Fig. Only two nuts hold the housing to the cylinder head

de736db.jpg

Fig. Pull the housing straight out to remove
  1. Remove the thermostat and rubber O-ring gasket from the water inlet housing.
f722bd2.jpg

Fig. Then pull the thermostat and gasket out

bd62248.jpg

Fig. Sometimes the gasket is stuck and has to be pried out of the head
To install:
  1. Make sure all the gasket surfaces are clean. Clean the inside of the inlet housing and the radiator hose connection with a rag.
  2. Install the new rubber O-ring gasket onto the thermostat. On 5S-FE engines, align the jiggle valve with the upper side of the stud bolt. Insert the thermostat into the housing.
abce49b.jpg

Fig. Only use the correct temperature range thermostat when for replacement

edd75f2.jpg

Fig. Align the jiggle valve within a 10°gap of the stud bolt-7A-FE engine

d56a45f.jpg

Fig. Align the jiggle valve within a 5°gap of the stud bolt-5S-FE engine
  1. Position the water inlet housing with the thermostat over the studs on the water pump and install the two nuts. Tighten the two nuts to 78-82 inch lbs. (9-10 Nm).
Don't forget to install a new O-ring onto the water inlet pipe. Apply soapy water to the O-ring prior to installation.
  1. Connect the lower radiator hose to the inlet housing and install the hose clamp.
  2. Attach the water temperature switch connector.
  3. Install the oil filter and check the oil level if removed.
  4. Fill the cooling system with a good brand of ethylene glycol based coolant.
  5. Start the engine and inspect for leaks.
  1. Remove the right hand cover under the engine.
  2. Drain the engine coolant.
  3. Remove the fan and generator V belt.
  4. Remove the generator assembly
  5. Remove the water inlet via the two nuts.
  6. Remove the thermostat.
To install:
  1. Install a new gasket onto the thermostat.
  2. Install the thermostat with the jiggle valve upward. It can be set within 10 degrees on either side of the prescribed position.
  3. Install the water inlet via the two nuts. Torque to 8 ft. lbs. (11 Nm).
  4. Install the generator assembly.
  5. Add engine coolant.
  6. Inspect for leaks.
  7. Replace the cover under the engine.
I hope help you with this (remember rated this help) Good luck.

Sep 29, 2009 | Toyota Celica Cars & Trucks

2 Answers

How to replace thermostat


1994 Toyota Camry 2.2L EFI DOHC 4cyl
On both diesel and gasoline engines, the thermostat is located in the water inlet housing connected to the lower radiator hose.

R
CAUTION Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
Gasoline Engines
(see Figures 1, 2, 3, 4, 5, 6 and 7)
  1. Position a suitable drain pan under the radiator drain **** and drain the cooling system.
  2. On the 1MZ-FE engine, remove the air cleaner cap assembly. Be sure to label all wiring disconnected.
  3. Disconnect the water temperature switch harness from the water inlet housing (except 5S-FE engines).
  4. Remove the oil filter on 5S-FE engines. On the 1MZ-FE engines, remove the heater hose covering the housing.
  5. Loosen the hose clamp and disconnect the lower radiator hose from the water inlet housing.
  6. Remove the two nuts from the water inlet housing and remove the housing from the water pump studs.
  7. Remove the thermostat and rubber O-ring gasket from the water inlet housing.
To install:
  1. Make sure all the gasket surfaces are clean. Clean the inside of the inlet housing and the radiator hose connection with a rag.
  2. Install the new rubber O-ring gasket onto the thermostat. On 2SE and 3S-FE engines, align the jiggle valve of the thermostat with the protrusion on the water inlet housing. On 5S-FE engines, align the jiggle valve with the upper side of the stud bolt. On 2VZ-FE and 3VZ-FE engines, align the jiggle valve with the stud bolt. Insert the thermostat into the housing.
762d5d3.jpg

Fig. Fig. 1: Remove the thermostat housing from the engine with the coolant temperature sensor-1MZ-FE engine

1994ef0.jpg

Fig. Fig. 2: Removing the thermostat from the engine-1MZ-FE engine

4344e0c.jpg

Fig. Fig. 3: Always discard the old O-ring from the thermostat, if reusing the old component

2ff0a56.jpg

Fig. Fig. 4: Always replace the thermostat with the correct temperature specifications

e50fd7b.jpg

Fig. Fig. 5: The thermostat is placed in between the housing and the cylinder head as shown here-2S-ELC and 3S-FE engines

f5e46a6.jpg

Fig. Fig. 6: Line-up the jiggle valve with the protrusion on the housing-5S-FE engine
  1. Position the water inlet housing with the thermostat over the studs on the water pump and install the two nuts. Tighten the two nuts to 78 inch lbs. (9 Nm) on 4 cyl. engines, 2VZ-FE and 3VZ-FE; 14 ft. lbs. (20 Nm) and 69 inch lbs. (8 Nm) on 1MZ-FE engines.
62e4095.jpg

Fig. Fig. 7: Thermostat installation-2VZ-FE and 3VZ-FE engines
Don't forget to install a new O-ring onto the water inlet pipe. Apply soapy water to the O-ring prior to installation.
  1. Connect the lower radiator hose to the inlet housing and install the hose clamp. On the 3VZ-FE, tighten the bolt holding the water inlet hose to the alternator belt adjusting bar to 14 ft. lbs. (20 Nm). On the 1MZ-FE engine, tighten the bolt retaining the water inlet pipe to the cylinder head to 14 ft. lbs. (20 Nm).
  2. Attach the water temperature switch connector.
  3. On the 1MZ-FE engines, install the heater hose removed.
  4. Install the oil filter and check the oil level if removed. Install the air cleaner cap assembly on the 1MZ-FE engines.
  5. Fill the cooling system with a good brand of ethylene glycol based coolant.
  6. Start the engine and inspect for leaks.

continue...

Sep 29, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
1992 Toyota Camry V6 Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...