Question about 2007 Nissan X-Trail 2.2

Open Question

Need to know the correct marks on gear and camshaf

Vehicle is swinging but not starting

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show me timing gears aligment from crankshaf to camshaf, wl 2.5 diesel bravo


They will have dot or line marked on the cam gear pump idler gears and front pulley turn motor over until TDC come up on harmonic balancer remove covers and marks should line up on cogs,mark all pointer,s with white out so it all goes back the same ,try Google on the computer they often have a video.

Jan 26, 2017 | Cars & Trucks

1 Answer

I am broken down and vehicle swings over but will not start. Engine light is on. battery is good. Beeping noise while swinging


Tthat beeping noise is telling u whats wrong dont let the battery die it will clear the code and u wont find ur problem so charge it every week i need to know the beeping on it

Jan 06, 2015 | 2006 SsangYong Rexton RX

2 Answers

Timming belt broke from water pump broke while driving car put new water pump on n timming belt but car doesnt start right plus shakes doesnt sound right 2001 neon dodge


Sounds like timing belt not on correctly. Check timing marks are aligned correctly when installing timing belt. This vehicle should have 2-3 marks to be aligned when installing belt.marks should be on cam gear/ crankshaft gear and intermediate shaft if engine is equipped with it.

Sep 10, 2011 | Dodge Neon Cars & Trucks

1 Answer

What or where are the timing marks for 2002 hyandai accent 1.6


The timing marks allow the engine to be correctly timed . It depends on what you are trying to do . If you are just trying to time the engine with a timing light .Then the mark that you would look for would be on the harmonic balancer thats the lower pully that that fits over the front of the crank shaft there will be a corasponding mark on the vehicle next to the pully that has marks in degrees that you can line up with the pulley as it turns and you use a timing light attached to #1 cylinder and ground to see this alignment the light flashes as the engine turns and lights the point up at the correct time to see it . Then you adjust the disturbutor to control where the mark moves so you can make the alignment move by turning the shaft . If you are talking about timing marks on the timing chain gears then there is a dot on each gear upper and lower and they need to be aligned in the middle so the lower gear the dot or mark is at the top of the gear and the upper or cam gear is faceing down but this alignment needs to be a perfect alignment if its off by 1 tooth you will know it the vehicle will not run vary good and back fire a lot

Mar 29, 2011 | Hyundai Accent Cars & Trucks

1 Answer

How do I find the timing marks to time a 4-cyl 93 Caravan engine? I have the crank gear and camshaft gear already exposed and new belt already on. I need to know how to align it to the proper position.


The crankshaft gear has a center punch mark on gear and the intermediate gear has a line mark on gear. Rotate the crank until the #1 piston is top dead center. In doing so the crankshaft mark should line up with the intermediate gear mark. (crankshaft mark at 1 oclock and intermediate gear mark at 7 oclock). At the same time look at the cam gear and the small hole should be at the top and the two larger holes should align with the bearing cap. ((parting line should be looking at it will be 50/50 when you look at the front of cam gear). Remember to remove belt before timing engine correctly. Also make sure the negative wire is disconnected from battery before starting this job. Hope this will help you.

Jun 01, 2010 | 1993 Dodge Caravan

3 Answers

We change the cambelt and something very wrong happened, after putting everything together and starting the car.. it sound really wierd and the car is shaking. Probably the geerwheels are in wrong...


put number one cyl to tdc take out plug put long screwdriver down to check this if you are not sure /check marks on cam pulleys are correct at this point you need to use locking tool to hold pulleys still .if used before you would not have had a problem re fit belt tension turn over 2 times re check marks re check belt tension should be ok now unless valve has got bent moral always lock the camshafs on twin cam engines

Dec 16, 2009 | 2001 Volvo S40

1 Answer

Nned to know how to set the cam and engine timing


Start with crankshaft pulley. At the rear of the pulley is a notch. Align it with the mark on the oil pump.(No 2 piston is at TDC) There is also a groove on the pulley that needs to be aligned with the white dots on the cambelt. The lettering on the belt must be readable as viewed from the front of the vehicle.
(When seated in the vehicle the RH bank of the engine is on the RH side of the vehicle.Keep this in mind)
At the front of the camshaft pulley is a groove. Rotate the RH bank camshaft pulley to align this groove with the mark on the cylinder head cover. On the cambelt is a white line. This must also align with these marks. Do the same on the LH bank. To be sure the cams are now correctly aligned remove the cylinder head cover. On the camshaft drive gears the letters RI(Right intake) and RE(Right exhaust) will be at the top and readable for the RH bank. (For the LH bank it will be LI and LE) Reinstall the tensioner and rotate the crankshaft with a wrench to make sure there is no unintentional mechanical contact.

Dec 10, 2009 | 2002 Isuzu Rodeo

1 Answer

My 2004 bmw x5 jerks when first putting the vehicle in forward gear. Only happens when starting out. Afterwards it is mooth sailing.


hi , you may need to get the gear box oil level checked as this seams that it may be a little low , you could also tryrunning the engine for a minute or so , this would allow the oil to warm up and hopefully engage the first gear correctly , regards mark

Jul 29, 2009 | 2004 BMW 5 Series

1 Answer

I need a diagram to show me how to replace my timing chain on a 94 gmc cierra p/u truck 4.3l engine v 6 2 door extended cab


I don't have a diagram but here are written instructions.

I don't know how much you know about the subject so I will start at the beginning. First you have to get to it, you can pull the motor or leave it in the vehicle. Its a little harder with it in depending on the space you have in engine compartment. If your leaving the motor in, which I imagine you are, your going to have to take the front end of the vehicle apart. Remove the grill, bumper if need be, radiator, fan, water pump, harmonic balancer, you will need to buy a puller and a installer for the harmonic balancer. You can get a puller kit from harbor frieght tools for $10. You can buy the installer from Summit racing (web site) for around $30 or you can buy one that will do both the install and removal from summit for $70. Once you have removed your harmonic balancer you can remove your timing cover to expose your timing chain. Turn the motor using a socket wrench until the timing marks on the crank gear and cam gear line up. The marks are usually just white dots, you want the crank mark to be up towards the cam and the cam mark towards the crank, the marks will be up and down from each other. Once you have the marks lined up remove the bolts holding the timing chain to the cam and crank. Remove the timing chain as a whole unit with the cam and crank gear still on it. If the crank gear doesn't want to come loose use your puller on it. when you get it off just put your new gear on and line up the timing marks then put it back on as one unit. If you cant get the crank gear on all the way by hand buy a crank install tool (summit) they run about $24. While you have the thing apart it would be a good Idea to put a new timing chain on. Depending on your vehicle this would also be a good time to change your cam if need be. Its not that hard to do it just takes a while, take your time and don't force anything. If you need anymore help my email is sterlingljles@yahoo.com

Jul 19, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
2007 Nissan X-Trail 2.2 Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...