Question about 1992 Mitsubishi Galant

Open Question

Upon start it makes a loud rattling noise.

Also it wont shift until it red lines.

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission make loud sound when put it in revers


PLEASE HELP! SOS! car starts but doesnt move! - Club3G Forum ...

www.club3g.com > ... > Performance & Tech Forums > Problem Reports

Nov 16, 2010 - 61 posts - ‎14 authors
now yes, i will take the transmission is fubar into consideration but theres an .....however... idk about my cv joint, my car ONLY would make a loud ping noise when i move from a stop or brake ..... almost always when i put it into reverse. such as an engine mount sound, ... Vehicle: 2004 Eclipse Spyder GT. Loud knocking sound after oil change..
14 posts
Sep 20, 2010
Horrible noise upon start when cold
21 posts
Dec 24, 2009
Sporty knocking.. Oh noez!!one!!1!
16 posts
Mar 22, 2006
More results from www.club3g.com

Loud thump when I shift into drive or reverse - CarGurus

www.cargurus.com > Questions > Chevrolet > Cavalier

CarGurusDec 19, 2012 - And while driving loud thump when car motor shifts th... ... Bad throttle position sensor can trip both lights and make the transmission shift at high rpms and shift hard even under light acceleration. .... the transmission will shift hard when firstput into reverse or drive ... 2004 Chevrolet Cavalier LS For Sale.Missing: mitsubishi ‎eclipse

Mitsubishi Transmissions & Drivetrains Repair Questions ...


Dec 06, 2015 | 2004 Mitsubishi Eclipse

1 Answer

Waht would cause a loud rattleing noise in my engine?


get it into a garage before something really goes bad then you'll be looking for a new beamer

Apr 29, 2014 | BMW 325 Cars & Trucks

1 Answer

Rod knock upon start


Not sure on model but to me sounds like its a dodgey valve lifter when the seals start to go they cannot hold the oil and when there under pressure they basically empty them selves hence when you turn the engine off and restart you get a rattle sound untill the valve fills again as long as the cars running ok leave it untill you have to replace them unless there easy to do sone are sone are a pain

Jul 04, 2017 | 2004 Nissan Maxima

2 Answers

BAD VIBRATION AND HUMMING NOISE AT 70KM/HR


Have the wheel bearings / wheel balance checked.

Mar 02, 2012 | 2003 Honda Pilot

2 Answers

I hear a loud ratteling noise coming from where


The rattle is likely a loose shield or a bad catalytic converter. As for the loud banging, Have you checked the front U-joints behind the brake rotors. As for the Reverse noise? Auto or stick shift?

Apr 16, 2010 | 1996 Jeep Grand Cherokee

2 Answers

My a/c compressor pully is making noise when the engine is running .


If it is indeed the pulley and not the compressor itself than all you have to do is pry slightly against the A/C clutchplate at equal and opposite spots( 3:00 and 9:00) this will bring the plate back to where it was upon assembly. Thank you, Dana P.S. if the clutch is making noise while the compressor is running than you've got to address that by replacing the compressor.

Jan 22, 2010 | 1999 Dodge Dakota

2 Answers

Loud noises


your torque converter could have went. i feel its definetly your trans. i need more input

Dec 15, 2009 | 1987 Chevrolet Blazer

2 Answers

I have a 2001 Ford ranger supercab that makes rattling noises. It has a 4.0L SOHC. It makes a very fast and loud metallic rattle wich softens anfter about a second or so when I first start it for the day....


4.0l's are notorious for valve rattle on cold start-up. There is really nothing you can do to make it go away short of completely replacing the valve train in the top end, and that isn't a permanent fix. It's is an top end oiling issue from the factory. Just don't race your engine on cold start-up until the rattle stops.

The rattle in the transmission sounds to me to be more of a loose dust shield/heat shield around the transmission or exhaust than a mechanical issue.

Oct 20, 2009 | 2000 Ford Ranger SuperCab

1 Answer

4 wheel drive wont disengage


shift motors are stuck.or check to make sure shift motors getting vacuum.

Apr 17, 2009 | 1991 Ford Bronco

1 Answer

Truck wont shift automatic. stays in 3rd gear. can shift manually


either repair or replace the transmission...sounds like the sensor went out

Dec 14, 2008 | 2001 Dodge Dakota

Not finding what you are looking for?
1992 Mitsubishi Galant Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...