Question about Cars & Trucks

1 Answer

How do i get the piston pin out a 400 ex - Cars & Trucks

Posted by on

1 Answer

Engine Shop or Parts Store that presses those type parts

Posted on Mar 27, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 Dodge Neon 2.0 Head gasket fail between #3 and #4 cylinder.


YES SOUNDS LIKE A FAILED WRIST PIN, PISTON SLAP IS MOVEMENT OF PISTON INSIDE OF CYLINDER
piston-slap-5xkokgp1sqa4wuqzkxul4kgu-2-0.png

Feb 22, 2017 | Dodge Cars & Trucks

1 Answer

What if it is the piston pins?


Hard to say but very bad either way.
It is going to take some serious investigation and corrective action either way. Biggest issue will likely be where to stop - If you dig in and find a bad wrist pin, do you replace that and button it all up and hope for the best or keep looking and replacing stuff?
Good luck and if you have time, add in developments via comment to the original question.

Jan 05, 2015 | 1996 Lexus LS 400

1 Answer

I do not havbe hyd press. Is there any other way to press the pistons off the connecting rods so I can install my new pistons, without damaging the new oistons


with press fit wrist pin pistons the only way is the use of a hydraulic press and they will have to be checked to make sure the wrist pin and piston is centred to the con rod.

Aug 29, 2014 | Cars & Trucks

1 Answer

Replacing piston


If you have 100k miles or more I might not bother with the piston. You're probably better off purchasing a good used motor and having it installed for about he same or less cost unless you plan on doing the work yourself. The piston can be $400 alone. Then labor, gaskets , fluids, maybe another $1000. Then we have to worry about the other pistons. What caused the problem to begin with.

Apr 04, 2014 | 2001 Audi A4

1 Answer

Hello, i have an old L65 Husqvarna chain saw, i have been lookin for a piston kit, but with no luck, i was told that old style 48mm piston out of Husqvarna model 61 will work in a l65 . Can any one co


I have a homelite piston running in my Husqvarna edger . Most pistons for engines are all the same if the cc's are the same . they only vary in the gudgeon pin size and the location of the pin in the piston. So take your piston to a small engine wreckers and any piston that measurers the same ,looks the same will do the job. then get a new piston for the make that it came out off and it will fit.

Mar 28, 2014 | 1993 Nissan Pathfinder

1 Answer

Steps to replacing rear brake pads


A special tool is required to compress the caliper piston on the rear brakes-don't use a C-clamp on the piston.
Raise the vehicle and remove the tire. The rear calipers have only one guide pin. Remove this pin and raise the caliper. Remove the old brake pads. Using the special tool compress the caliper piston-the piston will have one or two slots on it. These slots must in the correct position to remount the caliper. Install the new brake pads and slide the caliper back over the rotor and replace the guide pin. If the caliper doesn't slide over the rotor you'll need to reset the slots on the piston. Replace the tires and you're ready to go.

Jan 01, 2011 | 2000 Buick LeSabre

1 Answer

Emgine ribuild question


Well, any lateral movement of the connecting rod with the piston is not acceptable because it could wear to the point of being thrown apart over time.

Also, pins can be pressed out, I believe, even though I have never done this.

I have overhauled a 1979 Honda Accord and took the pistons out, but the machine shop said that they were ok, at the time.

Jul 04, 2010 | 1997 Toyota Tercel

2 Answers

Any Special tools needed for brakes on 2004 Suzuki Verona


for the fronts all you need is a set of metric sockets and a ratchet,use a c clamp to push back the caliper piston.remove the caliper mount bracket and rotor is out reverse install. now for the back if rotors have emergency brake using the same pads then you will have to buy a special tool to help you screw in the caliper piston tool costs lees then ten dollars.small cube with universal pins on each side also to be used on other vehicles.

Jan 14, 2010 | 2004 Suzuki Verona

1 Answer

1999 honda accord ex v6


The back brakes on my Honda Accord are disc brakes. After removing the brake cylinder assembly you will see the brake cylinder piston end has a slot in it. The short pin on the back side of the inner brake pad fits into this slot, but also it is used to 'Turn' (clock-wise) the piston back into the cylinder so you fit the assembly back over the new 'thicker' pads. You can not 'press' this piston back into the cylinder.

Nov 30, 2008 | 1999 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...