Question about 1991 Nissan Stanza

1 Answer

Clutch pedal goes almost to the floor before it engages

I added fluid and now the clutch pedal goes almost to the floor before it engage

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 82 Answers

If your fluid was low (which is why you likely added some,) you may need to "bleed" your clutch master cylinder.

Posted on Mar 27, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need a clutch pedal diagram for a 1999 s10 2.2 4cyl manual trans


Sorry no diagram. But here is how it works. In the start position(Power) the wire goes to the start fuse, from the fuse it goes to the clutch pedal switch. Push the pedal and it goes to the starter relay. On the other end is ground. If it is good it pulls the relay closed. On the closed end is battery power to the starter.

Mar 09, 2016 | 1999 Chevrolet Silverado 1500

1 Answer

How to adjust 95 geo tracker clutch


engaging?
you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 23, 2014 | Geo Tracker Cars & Trucks

1 Answer

How to bleed the clutch system


You need to reverse bleed it with a special tool.

Mar 26, 2014 | 1991 Nissan Stanza

1 Answer

Intermittent clutch failure


Either there is low clutch fluid or air in the system. Or the clutch slave cylinder is leaking within itself.

Jul 04, 2017 | Toyota HiAce Cars & Trucks

1 Answer

Clutch will not engage when it was engaging perfectly to begin with.


Your car has a hydraulic clutch release system, it is defective, either the master or slave cylinder is leaking or pulling in air and this causes the clutch pedal to go to the floor.

Aug 06, 2012 | Cars & Trucks

1 Answer

My clutch pedal used to be pretty stout and the clutch would engage at about the midway point to the floor. All of a sudden the clutch pedal is pretty free to the floor where the clutch now engages. what...


sounds to me like the clutch master cylinder might be bad usually this happens when the line or the clutch master cylinder leaks fluid and you lose pressure to your clutch pedal...you should have a hydraulic clutch on this truck...if its leaking it will need to be replaced its located under the truck usually on the drivers side mounted on the transmission bell housing...hopes this helps

Mar 21, 2011 | 1985 Toyota Pickup

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

3 Answers

Clutch pedal sometimes engages when near floor


Check fluid level on clutch reservoir. Check also for any leaks at the clutch clyinders and lines. if it is low on fluid, or you have to drain fluid, remember to bleed the clutch.Have somebody pump the clutch and turn the clutch bleeding screw until only fluid comes out.

Feb 28, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
1991 Nissan Stanza Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...