Question about 2005 Toyota LandCruiser Prado

Open Question

Solenoid diagram hi I have landcruiser 80ser- its a 1990 model do you have diagram for the glow plug solenoid as my seems to have fialed but not sure how to test it .

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 55 Answers

SOURCE: i have to glow my landcruiser a few times before

It may be time to change the injectors and a tune up

Posted on Dec 11, 2009

Ad
cantanko
  • 11 Answers

SOURCE: No charge?

The batteries on the diesel 'cruisers are strange in that under normal running the two are wired in parallel. When you turn the key to the "start" position, the battery relay wires them in series to provide 24 volts to the starter. Therefore, if either one of the batteries dies, you won't be able to start the truck as both batteries are required in order to provide 24 volts.

The wiring diagrams are available in Toyota publication RM315E. A search of the ih8mud forums should provide you with a download link.

Posted on Apr 25, 2010

cantanko
  • 11 Answers

SOURCE: land cruiser vx turbo diesel 1990 80 series.

Track down Toyota publication RM184E - a search of the ih8mud forums is a good start to finding it.

Posted on Apr 25, 2010

  • 1 Answer

SOURCE: 1990 Toyota Landcruiser Automatic Transmission

My 1990 VX Landcruiser auto loses drive when left overnight.
When I bought it the throttle pressure cable was broken and the auto had been over heated, otherwise it goes good.

Posted on Feb 10, 2011

  • 14036 Answers

SOURCE: 1990 carberetor toyota landcruiser diagram

try this www.ask.com/carburetor+schematic

Posted on Sep 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

80ser landcruiser 1fz4.5 got no power to fuel pump


Check fuses first. Then locate the fuel pump relay. Check power sources and ground circuit with a volt meter to make sure the relay is functional or swap in a new relay to check.

Oct 28, 2014 | Cars & Trucks

1 Answer

I have a 1990 landcruiser with a 3f engine, i just replaced the carburetor and set idle mixture screw to 2 and 1/2 turnsout as the book says but i cant get it to idle at all. Standard aisan carb. Any


check that the idle solenoid shut off needle is connected . It is used to stop engine run when the ignition is turned off. If it is not connected the idle circuit of the carby will not function and the engine stops.

Jan 06, 2013 | Cars & Trucks

1 Answer

Landcruiser 05 1HZ, Glow Plug Light comes on when I decelerate and goes off when I accelerate again - any idea


Hello kbmind, A number of different glow plug systems were used on the Landcruiser, depending where it was made and what country it was shipped to. However, they all serve the same purpose on a diesel injection. To preheat the combustion chambers. If your light is on when you deaccelerate the control module thinks the cylinder is cooling down & fires up the glow plug. This usually indicates the glow plug relay is weak and/or the glow plugs themself are worn.
Depending on your mileage, i would say it's the relay. The glow plugs can be tested with an ohm meter to determine if they need to be replaced. I hope this helps.

Sep 17, 2011 | 2004 Toyota Land Cruiser

1 Answer

100 series landcruiser glow plug light stays on


I have a 2005 1hz landcruiser, the "glow Plug Light" comes on when I release the accelerator pedal and then goes "off" when I accelerate - any ideas - thanks

Feb 22, 2011 | 2004 Toyota Land Cruiser

1 Answer

1990 Toyota Landcruiser Automatic Transmission Repair Diagram


My 1990 VX Landcruiser auto loses drive when left overnight.
When I bought it the throttle pressure cable was broken and the auto had been over heated, otherwise it goes good.

Jan 25, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

Land cruiser vx turbo diesel 1990 80 series.


Track down Toyota publication RM184E - a search of the ih8mud forums is a good start to finding it.

Mar 12, 2010 | 1990 Toyota Land Cruiser

1 Answer

I have to glow my landcruiser a few times before


It may be time to change the injectors and a tune up

Dec 11, 2009 | 2008 Toyota Camry

1 Answer

Having trouble finding out where the two orange wire run to from the glow plug solenoid. the glow plug soleniod on my 2002 250 super duty ford 7.3 is not working and there are two orange wires that i...


Check your solenoid by jumping it with an insulated screwdriver,(connect the 2 and hold for 30 sec.s), (it will spark atiny bit if u wiggle it around,) make sure the truck ignition is in the ON position FIRST , If this activates the glow plug system then the relay itself is the problem. Usually, it seems to me, the problem is the relay (or solenoid),the glow plug controller or the under valve cover wiring. The under valve cover wiring comes attached to your new valve cover gaskets.

Dec 02, 2009 | 2002 Ford F250 Super Duty SuperCab

Not finding what you are looking for?
2005 Toyota LandCruiser Prado Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...