Question about 2003 Mitsubishi Eclipse GTS

1 Answer

Removing manifold Change spark plugs

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 1,249 Answers

Good luck, buy a manual.

Posted on Apr 01, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How too install a valve cover gasket on a 01 Chrysler Sebring lxi


I guess you are wondering about those little rubber insert that are around all the bolts and spark plug openings. Replace them all. They will all be brittle and cracked by now adding oil drips and misfires from the spark plugs. Also change out the spark plugs and wires to save yourself the trouble of removing that upper intake manifold again. I had a dealer and 2 mechanic send me on a $1600 goose chase a few years back because they were too lazy too find the bad spark plug wire under the manifold. After a while I fixed it myself. I think Rock Auto has those rubber plug sets at a reasonable price.

Aug 20, 2015 | Chrysler Cars & Trucks

1 Answer

Wgolf.mk4.reg2000.removing upper part inlet manifold.


If you have a 2000 VW Golf 2.0 liter, the answer is yes. Just remove the top part of the intake manifold. A magnet and long handle allen key set will make the job easier for removing/ reinstalling the cap screws. Once manifold off, cover the intake holes with blue painters tape, to avoid dropping any thing down in them. Take care on plug wire removal. Change each plug one at a time. ***Tighten spark plugs with a torque wrench, spec 22 ft-lb in the Bentley manual. AEG, AVH, AZG eng codes***

Jul 08, 2014 | 2000 Volkswagen Golf

2 Answers

How many spark plugs are on the mercury milan 2007. I only found 3.


For 2007 Mercury Milan 3.0L SFI DOHC 6cyl the upper intake manifold must be removed to access the RH spark plugs only.
  1. Remove the upper intake manifold, if removing the RH spark plugs. Refer to the Intake Manifold procedure in the Engine Mechanical Section
  2. Disconnect the 6 ignition coil-on-plug electrical connectors.
    NOTE When removing the ignition coil-on-plugs, a slight twisting motion will break the seal and ease removal.
  3. Remove the 6 bolts and the 6 ignition coil-on-plugs.
    WARNING Only use hand tools when removing or installing the spark plugs, or damage can occur to the cylinder head or spark plug.
    NOTE Use compressed air to remove any foreign material in the spark plug well before removing the spark plugs.
  4. Remove the 6 spark plugs.

To install:
  1. Inspect the spark plugs, as outlined in this section.
  2. Inspect the 6 spark plugs.
  3. Adjust the spark plug gap, as necessary, to 1.32-1.42mm (0.052-0.056 in.).
    WARNING Only use hand tools when removing or installing the spark plugs, or damage can occur to the cylinder head or spark plug.
  4. Install the 6 spark plugs. Tighten to 15 Nm (11 lb-ft).
    NOTE Apply a small amount of dielectric grease to the inside of the ignition coil-on-plug boots before attaching to the spark plugs.
  5. Install the 6 ignition coil-on-plugs and the 6 bolts. Tighten to 7 Nm (62 lb-in).
  6. Connect the 6 ignition coil-on-plug electrical connectors.
  7. If removed, install the upper intake manifold

Hope helps.

Mar 07, 2011 | 2007 Mercury Milan V6 AWD Sedan

2 Answers

I need to know how to change the back three spark plugs on my 2008 ford edge , do i remove the manifold.to get to them, is it safe


Yes, you will have to remove the intake manifold. If you are mechanically inclined, it's not that hard. Looks complicated because of all the wires and hoses. Just take your time, keep track of everything you do, take notes if you have to, so everything goes back together the same way it came apart. Since you are going to all this trouble be sure you buy a premium spark plug. I wouldn't use Champion or Ford products. NGK Iridium would be my choice if they are available.

Jan 01, 2011 | 2008 Ford Edge

1 Answer

Hi, I need to replace the 3 rear spark coils and spark plugs. What is the easiest way to do this? Remove the Intake manifold? Aloha, Jim


It's hard but possible to do that without removing intake manifold , if you don't have experience and right tools , probably removing the intake is easiest way.
If you want to try hard way , you need to clear some room for your hands by taking vacuum lines out, that go to throttle body and throttle cable with bracket (two 10mm heads bolt) , on the other side of manifold take out pcv hose (just pull it out from intake manifold and turn it out of your way.don't worry about clamp , it will come out and go back the same way when you push it in)
The worst part of this job without removing intake manifold is disconnecting harness plugs from coils and braking loose spark plugs.(Practice first on front harness connectors.)
Good luck.

May 25, 2010 | 1994 Lexus Es 300

2 Answers

How to replace spark rear plugs?


The upper part of your intake manifold needs to be removed.I think Chilton lists spark plug replacement on your Caravan at something like 3 hours.

Mar 01, 2010 | 2000 Dodge Caravan

1 Answer

I want to change the spark plugs in my 2001mazda tribute


See the tips section of my profile on Fixya. I have complete instructions on how to change the plugs and coils.

Jul 05, 2009 | 2001 Mazda Tribute

1 Answer

2001 mazda tribute spark plug change


can 't you remove the coils insted of the intake ? It is much easier.

Sep 28, 2008 | 2001 Mazda Tribute

2 Answers

60K Service


From what I have been reading online... The upper and middle manifold MUST be removed to get to the spark plugs to change them. 3 hour job minimum. should cost between $300 and $500.

Sep 02, 2008 | 2002 Mitsubishi Montero

Not finding what you are looking for?
2003 Mitsubishi Eclipse GTS Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...