Question about 2004 Land Rover Discovery

1 Answer

Replace back turn signal light

How to replace back signal bulb

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 158 Answers

There are four screws that hold the lens on, remove them and you have access to the bulbs.

Posted on Jan 22, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to fix a back left turn signal?


Wild guess, in the process of fixing the tail light, you disturbed the signal connections. Go back through your work carefully, see if something is loose or bad connection.

Apr 09, 2015 | 2004 Toyota 4Runner

Tip

Both Lower Brake Lights Not Working


Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If the lower two bulbs fail no lower brake light operation will occur. I know what you're thinking, you might say two brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove either of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.

Checking the Turn Signal Switch: Most American cars are designed to have the brake light switch wiring intergraded into the turn signal switch. Because the brake light bulb and the turn signal bulb are one and the same the turn signal switch interrupts the brake light circuit and installs the blinker signal circuit when the turn signal switch is activated. If this switch fails it will not allow the brake light signal through to the brake light wiring. To test for this condition a car repair manual is needed to test incoming and outgoing electrical current. If brake light switch power is present at the turn signal switch but not at any outgoing brake light wires the turn signal switch has probably failed.

on Dec 18, 2009 | Honda Civic Cars & Trucks

1 Answer

How to change side turn signal bilb on a VW jetta GLS


There are two spring clams that hold the assembly into the fender, and these are at either side of the assembly, there is usually a screwdriver slot near either side. Gently pry the assembly out, and remove the lens and back, the bulb sits in the twist assembly in the lens. Replace bulb with a clean hand, so that oil and dirt don't get on the bulb surface, pull bulb straight out from socket, and replace by inserting bulb back in socket. Voila. Replaced Turn Signal Fender light.

Mar 25, 2012 | Cars & Trucks

1 Answer

1996 chevrolet C1500. The back left turning signal/brakes light is not working. Front left turning signal works fine.(Faster than usual). The bulb comes on when the headlights are on(steady), but does not...


The bulb for the turn signal/brake light is a double filament bulb. It will come on with the lights on, but should light the second filament, making it brighter, with the brakes applied or turn signal on. It could just be a bad bulb, but one common problem on these years of truck is the rear light circuit board and requires the whole assembly to be replaced. Start by checking the bulb first though.
Hope this helps. Good luck!

Apr 18, 2011 | Chevrolet C1500 Cars & Trucks

3 Answers

Rapid right turn signal on dash but no right rear turn ligt at all


What that rapid turn signal on the dash means is, the rear turn signal tail light is burnt out. This is how you know the bulb is bad. Replace the burnt out tail light bulb and you will be back to normal.

Jan 16, 2011 | 2008 Chevrolet Impala

2 Answers

My brake light and signal light stopped working on my 1998 dodge neon on drivers side back can you help?


Does any lights on the right side work? It sounds like the ground connection to the assembly is loose.

Jan 04, 2011 | 1998 Plymouth Neon

1 Answer

I have no signals and when brakes lights are on, lose brake light to either side turn signal is set on


Hi!!

If you activate the turn signal switch and you step on the brake pedal, the turn switch (on the steering column) deactivates the brake light to make the signal light more visible. The bulb for the stop and turn lights is the same.

Turn hazard lights ON. If they don't blink, replace turn/hazard flasher, If one or more lights don't come on, replace bulb.

Check fuse and circuit wiring for broken or loose connections. If all looks fine, check following:

If front turn lights work fine, check brake/turn bulbs.

If turn lights come on but don't blink, replace turn signal/hazard flasher.

If front and back turn lights don't come on, replace switch on column.

Let me know how it worked out, Good Luck

Mar 24, 2010 | 1991 Plymouth Acclaim

1 Answer

Turn signal light replacement on my 91 sedan deville


Under the hood, you should be able to find the socket for the bulb behind the lighting assembly. The back of the socket turns out about a quarter of a turn, then can easily be removed to replace the bulb.
It goes back in reverse.

Sep 14, 2009 | 1991 Cadillac DeVille

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

2 Answers

Turn Signal Not Working, But Parking & Back Brake Light Does


i would say try to replace the relay,(it should be in the fuse box) for the signals. if it's not that it could be the brain it's located in the colum of the steering unit.

Jan 06, 2009 | 2002 Ford Mustang

Not finding what you are looking for?
2004 Land Rover Discovery Logo

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...