Question about 2001 Mercedes-Benz C-Class

Open Question

ENGINE MANAGE MENT LIGHT COMES ON FAULT CODE 10087

FAULT CODE 10087

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2013 Chrysler T&C When I accelerate to pass a vehicle the engine light comes on and then van gets sluggish and accelerates very slowly.


When the check engine light comes on the engine control module stores a fault code, you need that fault code read to start to figure out what is going wrong.

Jul 13, 2017 | Chrysler Cars & Trucks

1 Answer

Reduce engine power light comes on 2005 buick lacross


The check engine light n or reduced power light comes on when the on-board computer detects a fault in engine driveability or performance, transmission control system or transmission, or the emissions system, and a fault code is set and stored in the computer. Faults that can set the check engine light can range from a vaccuum leak, engine mis-fire, low engine compression, faulty sensor such as O2 sensor or other engine sensor, hydraulic pressure loss in transmission, transmission shift solenoid, open/short in wiring harness, emission evaporative system leak, or one of over a hundred different reasons. The only way to know what set a fault code and turned the check engine light on is to have a diagnostic scanner hooked up to the on-board computer and read it for stored diagnostic fault codes. Many auto parts stores will do this service for free- (like auto zone)check with you local parts stores. If none in your area do, then you will have to take it to a shop and pay to have the computer read for stored fault codes. Without knowing the fault codes numbers, it would be irresponsible to guess as to the cause as there are hundreds of possible causes.

Nov 16, 2015 | Buick Cars & Trucks

1 Answer

Ssangyong rexton engine check light


Check engine light comes on when computer detects an engine fault code. Light is to let you know that a fault code is stored in the ECM. You will need a diagnostic scan-tool to retreive stored codes. Hope that helps a bit.

Mar 07, 2014 | Cars & Trucks

1 Answer

Engine light on my mazda cx 7 2007 comes on then i reset it and still comes on


Run fault codes and check why the engine light comes on Obviously the fault is still there. Did you replace the faulty part with a genuine unit because some cpu units do not recognise after market units and will still record a fault. Reset the cpu using a code reader

Sep 22, 2013 | Mazda Cars & Trucks

1 Answer

My check engine light comes on and off 1995 lasabre


this means a fault is occurring in the engine electronic controls or the emission control system, every time the fault occurs the light is set, when it clears the light goes off, there is a code set in the computers memory of this fault, go to the link below for instructions on how to retrieve that code.
http://www.extreme-check-engine-light-codes.com/GM%20OBD1%20Decoder.htm

Oct 26, 2010 | 1995 Buick LeSabre

2 Answers

My check engine light keeps appearing on my dash i have a subaru impreza estate 4wd 1993


THE CHECK ENGINE LIGHT COMES ON TO INDICATE THAT A FAULT HAS OCCURRED IN THE ELECTRONIC ENGINE OR EMISSION CONTROL SYSTEM, WHEN THIS LIGHT COMES ON A FAULT CODE IS RECORDED IN THE MEEMORY OF THE COMPUTER, YOU NEED TO HAVE THE COMPUTER SCANNED TO FIND OUT WHAT THIS FAULT CODE IS DO PROPER DIAGNOSIS AND TESTING CAN BE DONE TO CORRECT THE PROBLEM, COMMON FAULTS ARE DEFECTIVE O2 SENSORS ON THIS MODEL.

Mar 11, 2010 | 1993 Subaru Impreza

1 Answer

2002 Hyundai Matrix transmission problem. While driving the engine check light comes on and I am unable to kickdown to overtake. Whenever, I try to drive from a complete stop, the car seem to be lazy. I...


When the check engine light comes on a fault has occurred and a fault code or codes is recorded in the Powertrain control modules memory. What you need to do now is have the fault code or codes read and then perform diagnostics based on what the codes are.

Jun 16, 2017 | 2002 GMC Yukon XL

2 Answers

Check engine light on 1998 Z3 BMW


BMW engine light

Comes on if DME engine management system self diagnostic fault detected. Will stay on until codes are called up and memory erased.

With OBD read the code as follows. Turn on ignition key, press accelerator pedal to the floor five times within 5 seconds. The check engine light will remain on for 5 sec , blik off, come on for 2,5 sec, go off for 2,5 sec and fault code will begin to flash. If more than one fault exist 2nd fault code will be separated by 2,5 sec pause. after fault codes there will be a 0.5 sec flash and light will remain off. to read codes again do procedure again.

Canceling of codes. make sure fault code is present (short blink and light goes out for long period), depress throttle pedal for at least 10 sec. read fault codes again and check for code 1444 (no faults stored.)

Check also the following, fuel pump, oxygen sensor, fuel injectors, engine coolant temp sensor, idle speed control valve, mass airflow sensor and too many other things.

Jun 16, 2009 | 1998 BMW Z3 Roadster

3 Answers

The engine light recently came on and now the engine spurts at acceleration.BMW328


when the engine light comes on the defect on the engine can be a blocked exhaust system or an air leak to the manifold. the oxygen senser monitors the runnig condition of the car and will inform you that the engine is not run correctly. diagnostic can tel you the defect

Jun 13, 2009 | 1997 BMW 328

1 Answer

Wont start mornings when warm starts good for a few times then wont again an also got i think engine management light come on in the dash when runing it comes on an off about half an hour apart


hi you need to get a reading off a fault code reader to find out what is causing the light to come on the engine manament light works off detecting not an individual fault it has to recieve this fault on 3-4 occassions before the light comes on if it doesn,t recieve a fault reading in a certain period of time it will presume the faults been fixed and the light goes out but 30 min period seems not enough time to for a reset the fault code reader should be able to store the fault code even ifs its not happening at the time but would be better if you can get the reading while the light is on yates210456

Oct 01, 2008 | Mitsubishi Passenger Cars & Trucks

Not finding what you are looking for?
2001 Mercedes-Benz C-Class Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...