Question about 2010 Chevrolet Impala

1 Answer

2010 impala dtc p2444

Dtc p2444

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 34,836 Answers

Has to be C244C through F to be valid.

Posted on Mar 26, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 4x4 is not working on my 2007 Yukon, I replaced actuator and the lights on the selective dial work but no dash warning light.


replaced what actuator ? The 4X4 switch on the instrument cluster ? Did you ever think of having it check for DTC'S - diagnostic trouble codes ? There are a number of them , they are there for shorting diagnostic time DTC B0770
DTC B0775
DTC B0780
DTC B0785
DTC B0790
DTC B2725
DTC C0300
DTC C0305
DTC C0306
DTC C0321
DTC C0326
DTC C0327
DTC C0359
DTC C0374
DTC C0378
DTC C0379
DTC C0550
DTC C0558

Feb 23, 2017 | Cars & Trucks

1 Answer

2001 Chevy S10 4x4 4L60E transmission works perfectly until 50MPH then I lose 3rd and 4th gear, 1st, 2nd and reverse are normal. Never happenend before, been parked since. Fluid is clean. Any ideas?


Are there any DTC's - diagnostic trouble codes ?in the PCM / BCM ? You have third an fourth below 50 mph but above 50 it down shifts to 2nd gear ,is this what your saying or you don't have 3rd or 4th gears at all ? Which engine did yours come with ? 2.2 L or 4.3 L You trans can set several DTC'S an not all will turn on the check engine light .
DTC B2722 (4.3 L) DTC P0218 (2.2 L) DTC P0218 (4.3 L) DTC P0502 (2.2 L) DTC P0502 (4.3 L) DTC P0503 (2.2 L) DTC P0503 (4.3 L) DTC P0705 (2.2 L) DTC P0706 (4.3 L) DTC P0711 (2.2 L) DTC P0711 (4.3 L) DTC P0712 (2.2 L) DTC P0712 (4.3 L) DTC P0713 (2.2 L) DTC P0713 (4.3 L) DTC P0719 (2.2 L) DTC P0719 (4.3 L) DTC P0724 (2.2 L) DTC P0724 (4.3 L) DTC P0740 (2.2 L) DTC P0740 (4.3 L) DTC P0741 (4.3 L) DTC P0742 (2.2 L) DTC P0742 (4.3 L) DTC P0748 (2.2 L) DTC P0748 (4.3 L) DTC P0751 (2.2 L) DTC P0751 (4.3 L) DTC P0752 (4.3 L) DTC P0753 (2.2 L) DTC P0753 (4.3 L) DTC P0756 (2.2 L) DTC P0756 (4.3 L) DTC P0757 (4.3 L) DTC P0758 (2.2 L) DTC P0758 (4.3 L) DTC P0785 (2.2 L) DTC P0785 (4.3 L) DTC P1810 (2.2 L) DTC P1810 (4.3 L) DTC P1860 (2.2 L) DTC P1860 (4.3 L) DTC P1870 (2.2 L) DTC P1870 (4.3 L) DTC P1875 (4.3 L) .
Shift Pattern This category contains the following topics:
?€¢
One forward gear only


?€¢
Two forward gears only


?€¢
Gear missing or slipping


?€¢
No upshift or slipping upshift


?€¢
No downshifts


?€¢
Non-First gear start


?€¢
Refer to First Gear Range Only - No Upshift .


?€¢
Refer to Third Gear Only .


?€¢
Refer to Second/Third Gear Only or First/Fourth Gears Only .


?€¢
Refer to Slips in First Gear .


?€¢
Refer to Slipping or Harsh 1-2 Shift .


?€¢
Refer to No 2-3 Shift or 2-3 Shift Slips, Rough or Hunting .


?€¢
Refer to No 3-4 Shift, Slips or Rough 3-4 Shift .


?€¢
Refer to No Part Throttle or Delayed Downshifts .


?€¢
Refer to Second Gear Start .

Feb 18, 2016 | Cars & Trucks

1 Answer

I put another abs moule on my 2002 Cadillac and lights are still on how do I clear the lights


Have the codes checked ! Do you know what codes are ,What the light is for ? The light is to warn the driver that there is a problem in the ABS system . Have the codes checked before replacing parts ,the code will point you in the direction to go .This system can set numerous DTC'S
DTC C1211 DTC C1214 DTC C1217 DTC C1218 DTC C1221-C1235 DTC C1236 DTC C1237 DTC C1238 DTC C1242 or C1243 DTC C1248 DTC C1251 (w/F45) DTC C1254 DTC C1255 or C1256 DTC C1261-C1274 DTC C1276, P1644, or P1689 DTC C1277 or P1571 DTC C1278 DTC C1281, C1283, or C1286 DTC C1282 DTC C1284 or C1285 DTC C1287 or C1288 DTC C1291 or C1293 DTC C1294 DTC C1295 Maybe your best bet would be to take your vehicle to a ASE certified repair shop or the dealer

Jan 10, 2016 | 2002 Cadillac Deville

1 Answer

I'm getting engine codes that I can't seem to find out what they mean. P0000 and P2444


P0000 don't know p2444 secondary air injection system pump stuck on bank 1

Apr 11, 2015 | 2009 GMC Canyon

1 Answer

What are the probable causes of DTC P2444?


Hello Please read this carefully. This info directly relates to the code you are having. I will include a troubleshooting tree at the bottom. If there are any other codes or if you need further info please let me know:

SYSTEM DESCRIPTION The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the AIR pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR valve relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The powertrain control module (PCM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.

The AIR diagnostic uses 3 phases to test the AIR system:
  • DTCs P0411 and P2430 run during Phase 1
  • DTCs P2430 and P2440 run during Phase 2
  • DTC P2444 runs during Phase 3
In all 3 phases, testing is accomplished by comparing the measured pressure against the expected pressure. The PCM can detect faults in the AIR pump, AIR control solenoid valve/pressure sensor assembly, and the exhaust check valve. The pressure sensor can also detect leaks and restrictions in the secondary AIR system plumbing.

The DTC P2444 Secondary Air Injection (AIR) Pump is Stuck ON diagnostic monitors the system pressure signal during test phase 3. When the PCM determines the AIR pressure sensor signal is higher than expected, DTC P2444 sets.

DTC DESCRIPTOR
This diagnostic supports the following DTC:
  • DTC P2444 Secondary Air Injection (AIR) System Pump Stuck On
CONDITIONS FOR RUNNING THE DTC
  • DTCs P0101, P0102, P0103, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0350, P0411, P0412, P0418, P0420, P0606, P0641, P0651, P1350, P2430, P2431, P2432, P2433, P2440 are not set.
  • The system voltage is between 10-18 volts .
  • The engine is running.
  • The start-up engine coolant temperature (ECT) parameter is between 5-50°C (41-122°F) .
  • The start-up intake air temperature (IAT) parameter is between 5-60°C (41-140°F) .
  • The BARO parameter is more than 60 kPa .
  • The MAF sensor parameter is between 3-24 g/s .
  • DTC P2444 runs once per trip start-up when the above conditions are met and the AIR pump operation is requested.
CONDITIONS FOR SETTING THE DTC
The measured AIR pressure is more than expected during AIR pump Phase 3 operation. DTC P2444 sets within 5 seconds when the above conditions are met.

ACTION TAKEN WHEN THE DTC SETS
  • The PCM illuminates the malfunction indicator lamp (MIL) during the first key cycle in which the diagnostic trouble code (DTC) sets.
  • The PCM records the operating conditions at the time the diagnostic fails. This information is stored in the Freeze Frame buffer.
CONDITIONS FOR CLEARING THE MIL/DTC
  • The PCM turns OFF the MIL on the third consecutive trip cycle during which the diagnostic has been run and the fault condition is no longer present.
  • A DTC will clear after 40 consecutive warm-up cycles have occurred without a fault.
  • A DTC can be cleared by using the scan tool Clear Information function.
DIAGNOSTIC AIDS

Inspect for any of the following conditions:
  • The resistance of the AIR pump relay coil (across terminal 85 and terminal 86) is 50-70 ohms at 20°C (68°F) . In the normal unenergized state, the resistance of the open relay contacts (across terminal 30 and terminal 87) is infinite.
  • The AIR pump relays electrical contacts may be pitted and sticking. Replace the relay if tapping gently on the relay or wiggling the relay causes a change in the relays operation.
  • The performance of the AIR pump relay may be affected by temperature. Check the relay after sitting outside overnight and after running the engine 30 minutes .
  • An intermittent malfunction may be caused by a fault in an AIR system electrical circuit. Inspect the wiring harness and components for an intermittent condition.


21812371-jq13pypi3egybe0aho3o0ljx-4-0.gif

The numbers below refer to the step numbers on the diagnostic table.
  1. This step tests for the correct operation of the AIR pump. When the AIR pump relay is commanded ON with the scan tool, only the AIR pump relay is energized. When the AIR valve relay is commanded ON with the scan tool, both the AIR pump and the AIR valve relays are energized.
  2. This step tests for the correct operation of the AIR pump relay.

Nov 27, 2013 | 2005 Buick LaCrosse

1 Answer

P2444 diagnostic code, what does it mean?


secondary air pump, check pipes for any splits

Nov 27, 2013 | 2005 Buick LaCrosse

1 Answer

How to fix P2430 code on a 2006 Pontiac Grand Prix


P2430 Secondary Air Injection System Air Flow/Pressure Sensor Circuit,
The AIR diagnostic uses 3 phases to test the AIR system:

DTCs P0411 and P2430 run during Phase 1
DTCs P2430 and P2440 run during Phase 2
DTC P2444 runs during Phase 3
During phase 2, only the AIR pump is activated. The solenoid valve is closed, this is p2430 and p2440. -The AIR system pressure sensor is stuck. good-day !!

Jul 15, 2011 | 2006 Pontiac Grand Prix

1 Answer

What does p2444 code mean on a 2008 chev colorado with a 2.9 eng.


it means the secondary air injection system pump is stuck on,could be a bad relay keeping the pump on,hope this helps

Oct 15, 2009 | 2008 Chevrolet Colorado 2WD

Not finding what you are looking for?
2010 Chevrolet Impala Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...