Question about Cars & Trucks

1 Answer

Indicator fuse keeps blowing hazards work perfectly

Fuse blows as soon as you put it in without using indicators.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

This indicates that somewhere in that circuit there is a short to earth check all accessable wiring for breaks etc

Posted on Mar 26, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't figure out why the tail and indicator fuse keep blowing on my sportage 2000 4x4 keeps blowing when try and turn on tail lights and blows indicator fuse when used to indicate left


Dead short. Use a multimeter to find short to ground. Look at spots where wiring is touching body or a tight clamp that may be cutting into wire. Follow all wires looking too and bottom.

Nov 03, 2017 | Cars & Trucks

1 Answer

Mitsubishi l200 indicator lights keep blowing a fuse


Put in a fuse that's rated 5 amps higher than the ones you are currently using. This won't harm anything. Otherwise you may need to install a current dampener on the line.

Dec 16, 2014 | Mitsubishi Cars & Trucks

1 Answer

Signal light fuse keeps blowing


the fuse stopped the fire. that is what fuses do.
so, you have a dead short on the blinkers.
remove each lamp 1 at a time.
yes, lamps can short. (twisted too hard)
remove them.
still blow the blinker fuse.?
yes, then the wires are shorted.
and guess what, top reasons are.
1: trailer wiring, look behind each lap assembly, BINGO?
2: hacking or collision, yes, look 1 more time. ,yes behind the lamp assembles, look carefully for DAMAGE.

Aug 05, 2013 | Suzuki Jimny Cars & Trucks

1 Answer

Indicator fuse keeps blowing


check the bulb holders first ,it could be the wrong bulb ,normally a single pole bulb but you may have fitted a double pole stop/tail light bulb by mistake ,Common fault i have come across

May 02, 2013 | 1990 Honda Accord

1 Answer

Where is the relay or unit for the indicator flasher?


I can tell you that my relays are under the hood, enclosed in a water tight box that is labeled on the inside with a diagram of the placement.

May 28, 2012 | 2002 Mazda Tribute

1 Answer

Turn lights wont work


The indicators have a few components in their system, being: The indicator switch The Flasher Unit/Relay The fuse & wiring The bulbs The Hazard light switch.
If the hazard switch is broken or disconnected it will stop the indicators from working, so you could check that. You can check the indicator fuse, which should be labeled on the fuse cover. If it is blown, there is likely a fault that has caused it to blow, more often than not a problem with the trailer hitch or a trailer that has been towed. The next culprit is the flasher unit. They are usually found in the fuse area, it is a black box, looks much like a relay, but slightly taller. If this is faulty it will cause the indicators to either stay on without flashing, or not work at all. You can check this by disconnecting it, and connecting a test light to the terminals, one at a time while working the indicator stalk (key on) If the light lights up then this confirms the switch is okay, and the flasher is likely faulty.

Mar 24, 2011 | 1994 Ford Econoline

1 Answer

Left indicator keep blowing a fuse on my RAV4 1998. Hazard lights dont work either. Any advice?


First is the check the bulbs/sockets for a short, on the
left indicators front and rear. Theres a short somewhere.

Nov 23, 2010 | 1998 Toyota RAV4

1 Answer

Problem with indicators lamps


What is 'CRDi'?... never heard of it.

Jun 23, 2009 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...