Question about 2003 GMC Envoy

1 Answer

2003 envoy radio is locked what to do.

My 2003 GMC envoy has a locked radio.. how can I resolve this

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 3,679 Answers

Contact suppling dealer if you know who that is ,or any dealer should be able to get you the radio code

Posted on Mar 26, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Air Vents 2003 Envoy

I have the same ploblem, I just wonder why this is not a recall yet? the other problem i got is the fuel gauge not working.

Posted on Aug 25, 2008

  • 4 Answers

SOURCE: How to replace the headlights on my 2003 GMC envoy.

The headlights on the envoy are the easiest parts of the car to repair. You just pull the two tabs at the top of the headlights, screw out the bulb containers and you are good to go

Posted on Nov 15, 2008

  • 1 Answer

SOURCE: 2003 GMC Envoy lower 3 heater fan settings quit working.

had same problem on my XUV. changed the blower motor resistor, located under passenger side dash. easy to change, works no problem.

Posted on Feb 17, 2009

  • 179 Answers

SOURCE: 2003 GMC Envoy stalling w/ AC on when stopping

try turning up the idle ajustment screw also have alternator checked, another solution would be to have your car tuned up weak spark from your coil worn plugs wires etc. not enough power is being produced

Posted on May 31, 2009

  • 691 Answers

SOURCE: how do you change brakes on a 2003 gmc envoy

don't need any special tools, standard sockets sets, "C" clams is a must unless your a He-Man and wrench set, plyer or needle nose will do. I assumed being 2003 your rotor never have been turn and i recommend every time you change your bakes is good idea to have your rotor turn. reason is it will make your pad last lot longer, removed any vibration and better even wear on the pad and eliminate any squealing although is not necessary to do so. make sure you get extra break fluid to bleed the brakes. get your self 5 feet long smallest vacum rubber hoses and a glass jar to bleed your brake fluid in. the rubber vacum hose you going to use to fit on to the bleeding nipple and run the other end of line to your the glass jar to save the brake fluid when you bleed the brakes. when removing caliper, check inspect make sure the rubber seals around your piston look good and not crack or deteriorated. before applying new pad make sure you open the bleed valve to reduce the pressure by turning the bleed nipple counter clockwise and leave it open attach that rubber hoses to the nipple because you going to press on the piston back into it housing with the "C" clamp in order for new pad to fit. becareful not to damage the rubber seals around the piston. its going to take lots of effort to push that piston back in so be a bare with it if needs to. once the pad is back in make sure you keep the reservoir full with brake fluid and then bleed the brake. two people is a good idea to do brake. one will do the pumping the brake and holding it down and other will bleed the nipple. I bleed it 2-3 time will do the job. good luck!

Posted on Jul 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear radio in envoy not working. It will not come on at all.Front radio works fine.


This is one of those mysteries of GMC engineering. I compared the Envoy without and with rear seat radio and found 10A HVAC FUSE B 36 (!) in the rear fuse block is the source of power. Replacing it may get your radio working again.

Dec 16, 2014 | 2003 GMC Envoy

1 Answer

Access code for 2003 envoy radio


costs money, it will never be free.
only how much and trouble are the variables.
is this SAT code? or is the radio bricked, from car battery dead.
if radio is dead, in all ways that is bricked.
aka: theft deterrent mode, asking for password.
http://www.fixkick.com/power-elect/Keep-Alive/keep-alive.html

Jun 11, 2014 | 2003 GMC Envoy

1 Answer

How do you unlock a factory radio put in a envoy xl


tech 2 require to reset radio. take to dealer

Apr 14, 2013 | 2003 GMC Envoy Xl

1 Answer

My 2003 gmc envoy says change oil and i just had oil changed what do i need to do


The Change Oil reminder needs to be reset. This done as follows;
1. Turn key to RUN position, do not start engine
2. Fully depress and release the accelerator pedal three times within 5 seconds
3. Turn key to LOCK position.

Oct 04, 2011 | 2003 GMC Envoy

1 Answer

Where is fuse located for radio on 2003 gmc envoy


Fuse #41 is located in rear fuse panel.

Jul 01, 2011 | 2003 GMC Envoy

1 Answer

I am not able to turn my radio on in my GMC envoy. Ant clock doesnt display


Hello
Possible fuse is blown.Check the owners manual for location of fuse box,usually on drivers side under dash board.
Remove cover of fuse box and inside is a list and location of fuses.Remove fuse for radio and replace with a known to be good fuse, same type...meaning 2 amp 5 amp or whatever the radio fuse was.

Nov 23, 2010 | 2003 GMC Envoy

1 Answer

Radio locked,need code


Te radio code for many cars can be found here:
http://www.radio-code.com/
Other options are the first Owner, and of course the Car Dealership.

Oct 24, 2010 | 2003 GMC Envoy

2 Answers

Where is the fuse box for a 2003 gmc envoy


There are two fuse boxes/block

One fuse block is located under the hood in the engine

compartment on the driver's side of the vehicle.

Remove the primary cover by pressing the two locking

tabs. Remove the secondary cover by snapping off

while lifting. To reinstall the fuse panel cover, reverse
the sequence.

The 2nd fuse box is located under the rear seat cushion

Oct 06, 2010 | 2003 GMC Envoy

1 Answer

Fuse location


In the Fuse Block (rear) check the position 41, 15AMP

Mar 05, 2010 | 2003 GMC Envoy

Not finding what you are looking for?
2003 GMC Envoy Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...