Question about 1999 Chrysler 300M

Open Question

Code p1288 and p320

No run

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford focus/ no start. fires once on initial crank then nothing


These three codes all point to the wrong voltages on wires that the engine computer monitors. The condition could be systemic, affecting many or most systems that run off battery power in the vehicle. The B code is a direct failure of ignition/accessory voltage at the control module.The ignition system needs this voltage to be present when you let go of the key after starting to stay running.

If you are good at troubleshooting electrics, this may turn out to be a cheap but time consuming repair. If you are not an electronic genius, find one for best results. Maybe just a fuse or burnt wire, but probably more complicated than that.

Mar 14, 2015 | 2002 Ford Focus

1 Answer

Engine code p320


Code 320 is for a problem with the circuit between the coil and engine computer that provides RPM signal. You'll probably need a shop manual to get the testing procedures.

Aug 24, 2014 | 2000 Ford Focus

1 Answer

2001 ford crown victoria 4.6L engine with codes p1288 and p1401


The 1401 code is for a DPFE switch or connector that is not sending the correct signal the PCM expects. The 1288 code is for a temperature sensor which may be showing a higher cylinder head temperature due to low coolant levels, blockage of water flow or bad thermostat.

The DPFE gives readings of the mix of exhaust gas returning into the intake manifold to be burned again to lower emissions.

The combination of these 2 codes can mean that too much exhaust gas is too frequently going into the intake manifold and is overheating the cylinder head causing the 1288 code. So fixing the DPFE may eliminate this secondary error which may reset itself after the first problem is fixed.

Nov 06, 2013 | 2001 Ford Crown Victoria

1 Answer

2001 Excursion 6.8 V10, hard start, high idle, code P1288 KOEO, and KOER, no memory codes, with temp gauge in normal range scan data reads 20 deg F, suspect CHT sensors looking for sensor location.


CHT -cylinder head temperature sensor located under the intake manifold.you have to remove intake manifold to replace sensor its in the cylinder head.

Oct 22, 2013 | Ford Cars & Trucks

2 Answers

Crank sensor code


actually the P320 means Ignition/Distributor Engine Speed Input Circuit
_____________
carprog, a strong car and truck diagnostic tool.

Mar 06, 2013 | 2005 Kia Optima

1 Answer

Check engine light on code p320


Trouble Code: P0320

Ignition Failure Sensor Circuit Malfunction

Possible Causes:


Ignition failure sensor circuit is open or shorted to ground.Ignition failure sensor is damaged or has failed.PCM has failed.

Jan 05, 2013 | Cars & Trucks

1 Answer

Location of the cylinder head temp sensor on a f250 2000


Did the problem come on suddenly or was some previous action or work done......

Nov 05, 2011 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Getting code p320 on my 2000 ford focus,I think it is the coil pack


The most likely cause of this is the crank shaft position sensor.

Apr 09, 2011 | Ford Focus Cars & Trucks

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...