Question about 2004 BMW 745i

Open Question

P2610 code p2610

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is p2610 ? how is affect the car performance?

P2610 is defective ECM/PCM, no IF's and's or but's about it.

Sep 23, 2016 | 2016 Toyota Camry

1 Answer

My Pontiac vibe 2006 is showing PO6006, PO6007 code does anyone ha be any idea what it means

P0606 , P0607 ! no such codes P06006 or P06007
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610
DTC P0606 Control Module Internal Performance
The DTC P0606 and P2610 set when the powertrain control module (PCM) has determined that the control module has an internal fault. The PCM performs continuous self checks of all internal circuits. There are 2 central processing units (CPU) within the control module. If the outputs from the two CPUs deviates from the standard level, a DTC P0606 sets. The control module has several internal clock or timer circuits. The DTC P2610 diagnostic monitors the internal timer circuit responsible for the ignition OFF operation of the evaporative emission (EVAP) system vacuum leak pump. If the there is an error in the control module timer, a DTC P2610 sets.

Feb 25, 2016 | 2006 Pontiac Vibe

2 Answers

What is code p2610

"DTC P2610 is set if an internal ECM problem is detected.
1.With ignition OFF, remove both ECM connectors.
2.Wait at least one minute.
3. Replace the connectors making sure to completely seat and lock them.
4.Turn the ignition ON with the engine OFF, and clear the stored codes.Verify the MIL light turns OFF, and stays OFF. If the MIL light does not turn OFF, repeat the clear code command until it the MIL light remains OFF.
5.Turn OFF the ignition and leave it OFF for at least one minute.
6.Turn the ignition back ON with engine OFF and observe that the DTC does not reset.
If the DTC P2610 is still set, repeat Steps 1 through 6 one additional time. If Steps 1 through 6 still do not correct the DTC P2610, verify there is constant battery voltage to ECM Connector C1- terminal 77. (circuit 440 / orange wire) If battery voltage is not present on Connector C1- terminal 77, troubleshoot and repair the circuit."

Oct 27, 2014 | Kia Sedona Cars & Trucks

1 Answer

2004 chevy aveo wouldn't start jumped battery and it started then code p2610 came on

Error p2610 means the clock in the ECM and soaker timer of the EVAP system doesn't syncronize. Usually that is caused by a bad ECM since it's all built-in. Try clearing the code first to see if it happens again.

Mar 29, 2014 | 2006 Chevrolet Cobalt

1 Answer

Code 2610, engine doesn't start same felling as if the battery too weak to prop up the engine

If a P2610 has been verified do not replace the ECM. Perform the following steps when encountering a P2610.

Turn the IGNITION OFF for 90 seconds. Unplug both the engine control module (ECM) connectors for 90 seconds. After 90 seconds has passed, re-install the ECM connectors. With the ignition on use the Tech2 and clear all codes in the ECM. This procedure should prevent future sets of the P2610. For 2006 and certain 2007 model vehicles, there may also be a calibration update available which addresses P2610 false sets.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Aug 07, 2013 | Chevrolet Optra Cars & Trucks

1 Answer

P2610 code aveo 2009


Jan 24, 2013 | 2005 Chevrolet Aveo

1 Answer

2005 Chevrolet Colorado OBDII code P2610

shevy colerado 2005 p2610 how pey for reprogram flash pcm

Jan 18, 2012 | 2005 Chevrolet Colorado

1 Answer

2007 chevy colorado DTC code P2610


Jan 11, 2012 | Chevrolet Chevy Cars & Trucks

1 Answer

Hi engine cose error from eobd reader says code p2610 how do i solve this please or what is the problem manythanks

Hi there!

The definiton of your fault code P2610 is ECM/PCM Internal Engine Off Timer Performance

The only info I have relates to this being an engine management ECU (DME) problem. The info doesnt go into specifics but says that the car requires a software update, then further diagnosis if this is unsuccessful. Worst case would be DME failure.

Apr 10, 2011 | BMW 3 Series Cars & Trucks

1 Answer

Check engine light is on; diagnostic code is P2610, What is that code and is it safe to drive my car until it is fixed?

p2610 is engine contro module or ecu the cars main computer for both fuel injection and ignition,Remove the large block connector going to the ecu and spray both with contact cleaner,should sort it.

Mar 04, 2010 | 2007 Toyota Corolla

Not finding what you are looking for?
2004 BMW 745i Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers


Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides