Question about 2005 Cadillac XLR

Open Question

REPLACE BACK UP SENSOR IN BUMPER

HOW TO REPLACE BACK UP SENSOR IN REAR BUMPER

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Backup signals in rear bumper


if your question is that my back up sensors stopped being accurate in my rear bumper , yes ive seen that , seems the brushes of auto car washes tend to frost them over making them less able to "see" whats behind the car they do pop out for replacement , just look to see what ones most frosted over (that's the dead one !!)

Jan 06, 2017 | Cars & Trucks

1 Answer

I recently had my rear bumper pulled off my car after replacing it my rear sensors in bumper no longer work


If you took it off, check the wires on the sensors. IF someone worked on it and charged for it, make them fix it. Make sure it is the right bumper and the sensors were not damaged.

Feb 05, 2016 | 2011 Lincoln MKS

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

1 Answer

Why are my backup sensors not coming on


if you have something in trailer hitch blocking bumper rear bumper dirty ,damaged rear bumper by sensor[s] or damaged /malfunction of sensor check the wiring and connections behind bumper those circular inserts are the rear sensors

Nov 16, 2015 | 2008 GMC Envoy

1 Answer

Rear bumper sensors not working


The sensors in the replacement bumper could be defective or possibly not connected correctly.

Dec 18, 2014 | 2013 Hyundai Santa Fe

1 Answer

Removing jaguar s type rear bumper..


disconnect the connector from the park aid module push the connector and grommet out of the back panel remove screws from lower rear of wheel arch liners remove boot floor trim remove plastic boot closing panel trim remove both boot side trims you wil find a number of 10mm headed bolts around the boot at the sides and back remove these and get someone to help you remove the bumper liner the 2 outer sensors can normally be changed without removing the bumper liner on some models

Mar 26, 2013 | 2003 Jaguar S-Type

1 Answer

05' Grand Caravan, told that 2 of the rear bumper parking sensors need to be replaced. What is the proper term for these, as I can't find them anywhere, and how invasive to replace?


I wish I had good news but rarly does this sensor go out. unless someone rear ended you. in this case the bumper cover has to be removed.

Dec 20, 2011 | 2005 Dodge Grand Caravan

1 Answer

Reverse censors are on constantly when in reverse.


One of your rear sensors ( 4 of them located on the back bumper) has most likely failed or was damaged. Check the back sensors for any visual damage (they are about the size of a nickle) and panted to match the rear bumpers paint.

Good Luck!

Nov 26, 2010 | 2003 Jaguar S-Type

2 Answers

I have a 2006 Ford Explorer and 2 of my park aid assist sensor are bad. They are in the rear bumper. How would i replace the sensors? Is it really necessary to remove the bumper?


You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Apr 01, 2010 | 2006 Ford Explorer

1 Answer

Rear bumper replacement


  Remove the tail lamps,remove the plastic retainers from the wheel well area. Remove the retainers below the tailgate opening and below the bumper. Lift up on the sides of the bumper to disengage the sides of the bumper. Pull it back a little and disconnect the connector for the park aid sensors if equipped. Pull back and it is off.

Oct 19, 2008 | 2003 Mercury Mountaineer

Not finding what you are looking for?
2005 Cadillac XLR Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...