Question about 2001 Lincoln LS

1 Answer

Say gas error data

Theft light is on flashing... an now dash says gas data error while light flashes?

Posted by on

Ad

1 Answer

Check for codes

Posted on Mar 26, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will cause a 1999 Pontiac Sunfire to not go into the extended learn mode when replacing the ign lock assembly .


Did you clear codes ? . All codes in the theft deterrent module must be cleared for a relearn.
PASSLOCK Changing - Components Description
Important: Due to component variability, the vehicle theft deterrent (VTD) system must have the learn procedure performed regardless, if the vehicle starts on the first ignition cycle after a VTD repair.
All codes in the theft deterrent module must be cleared for a relearn.
Engineers design the Passlock™ system in order to prevent theft even if the various theft deterrent parts change. The Tamper mode will engage if any of the following components change:
• The Passlock™ lock cylinder
• The instrument cluster
• The powertrain control module (PCM)
If you replace any of the above components, the system will enter the long tamper mode. If the system enters the long tamper mode, ensure that the system completes a long tamper mode cycle. During the long tamper mode cycle, the THEFT indicator will flash for the full 10 minutes. The instrument cluster and the PCM require the full 10 minutes in order to complete the learn cycle. Ensure that the ignition switch remains in RUN until the indicator stops flashing. If you turn the ignition switch before the indicator stops flashing, repeat the long tamper cycle from the beginning.
Are there any codes ?
Problem
Action
The THEFT SYSTEM indicator will not light under any circumstances.
Replace the instrument cluster.
For Chevrolet vehicles, refer to Instrument Cluster Replacement .
For Pontiac vehicles, refer to Instrument Cluster Replacement .
Multiple indicators light continuously.
Test for a loss of serial data. Refer to Data Link Connector.
Instrument cluster DTC B1021 sets.
The DTC indicates a loss of powertrain control module (PCM) serial data. Refer to Data Link Connector.
Instrument cluster DTC B1022 sets.
The DTC indicates a loss of SIR serial data. Refer to Data Link Connector.
Instrument cluster DTC B1023 sets.
The DTC indicates a loss of ABS serial data. Refer to Data Link Connector.
PCM DTC P1601 sets.
The DTC indicates a loss of PCM serial data. Refer to Data Link Connector.
PCM DTC P1629 sets.
The DTC indicates PCM Theft Deterrent failure. Refer to the appropriate diagnostic table in Engine Controls.
Instrument cluster DTC B1011 sets.
Refer to DTC B1011 Passlock Cyl Data Shorted This Ign Cycle .
Instrument cluster DTC B1012 sets.
Refer to DTC B1012 Passlock Bad R-code This Ignition Cycle .
Instrument cluster DTC B1013 sets.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle .
Instrument cluster DTC B1014 sets.
Refer to DTC B1014 Passlock R-code Unprogrammed .
Instrument cluster DTC B1015 sets.
Refer to DTC B1015 Passlock Cluster Fail Enabled .
Instrument cluster DTC B1017 sets.
Refer to DTC B1017 Passlock R-code Learn Failed .
The indicator flashes and no instrument cluster codes are set.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle (the diagnostic table for DTC B1013).

Apr 07, 2017 | 1999 Pontiac Sunfire

1 Answer

Anti theft reset in my mucury sabel 20010


Hi Melissa , why do you want to do a reset ? Vehicle not cranking over - engine not turning over ? When you try to start it is the red light on top of the dash flashing faster then with key off ? When key off a flash will happen every 2 seconds ! When trying to start it flashes very fast. If having a anti-theft problem the starter will not engage !

Jun 09, 2015 | 2003 Mercury Sable

3 Answers

How do i reset anti theft on 06jeep liberty. It wont let the gas. Go inyo the intake


Is there a theft light flashing? If so,use the key fob to lock and unlock the doors. This usually resets the system

Apr 27, 2015 | 2006 Jeep Liberty

1 Answer

Intermittent starting issue


If any aftermarket devices were installed and used these wires for power or ground can cause these issue.these wires are the main communication center for the whole car very hard to repair without specialty tools Dealer repair.

May 06, 2014 | Chevrolet Uplander Cars & Trucks

1 Answer

2004 ford freestar will not start the antitheft light keeps flashing


Look in ur 2004 freestar book and find the fuse it should be #9 (PATS FUSE)under the driver dash. Take the fuse out the lil red light on dash will not light anymore and ur van will start and keep the fuse out.

Apr 22, 2012 | 2004 Ford Freestar

2 Answers

2001 civilian model crown Vic. RED flashing light on top of dash


The 5 digit entry code is in the trunk, on the left hinge arm that holds the trunk lid.

Feb 15, 2010 | 2001 Ford Crown Victoria

Not finding what you are looking for?
2001 Lincoln LS Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...