Question about 2001 Pontiac Bonneville SSEi

2 Answers

Need to change Oil Pressure Sending Unit

Where is it located?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 189 Answers

Its right above oil filter on engine bottom

Posted on Jun 19, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 1,250 Answers

need to change Oil Pressure Sending Unit - 1adf95c4-4c1a-4981-9df3-c364df2924f1.gif

hope it helps

Posted on Apr 12, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Pontiac Bonneville(2000) oil pressure sending unit

The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Posted on Feb 02, 2009

  • 14036 Answers

SOURCE: where is the location of the oil pressure sending

it should be next to oil filter.

Posted on May 10, 2009

blueextc3221
  • 15935 Answers

SOURCE: changing the oil pressure sending unit on a 1996 2.2 pontiac sunf

Under hood, driver side, front engine area, below cylinder head, where engine meets transaxle housing mounted in block

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on Apr 23, 2009

  • 8 Answers

SOURCE: 1995 grand prix 3.1L engine

if it is oil pressure switch it is located in the front of the engine below valve cover and mounted in engine block.

Posted on May 12, 2009

  • 400 Answers

SOURCE: where is the oil pressure sending unit located on

Take the passenger front wheel off. Look up under the car by the power steering pump, you'll see the sending unit, it's up and back from where the oil filter is. There is a special GM oil sending unit socket, I'm sure you will be able to buy or barrow one from your local parts store! Make sure to have a catch pan under it when you take it out, they can leak a good amount of oil out when you remove it.

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

Oil pressure gauge is reading 80 psi. I had the


The oil sending unit is located on the engine block behind the drivers cylinder head area.You have to climb up on the motor to see it cause it is hard to see behind the wiring harness.You may also want to purchase a new sending unit because it is very long and you might need to buy the sending unit socket to replace it.Hope this helps.Good luck.

Jul 20, 2010 | 2003 Chevrolet Silverado 1500

2 Answers

Need to replace oil pressure sensor/or sending unit(getting low oil pressure idiot light when idleing in drive) 1997 dodge neon dhc 2.0L. I have a new one but cant seem to find where it is located on the...


In my experience with neon's the sending unit is most likely not the problem. I feel that you will find that the oil pressure is actually low and that the oil pump is going out. If you change the sending unit and it doesn't change then you will know for sure. The sending unit is located on the side of the block near the oil filter. It has one wire and simply unscrews and the new one screws back in and re-attach the wire. Hope this helps. Good luck.

Dec 03, 2009 | 1997 Dodge Neon

3 Answers

Where is the oil pressure sending unit located?


The pressure sending unit is located on the passenger side rear of the engine just above and slightly to the left of the filter and filter housing.

May 10, 2009 | 2000 Buick LeSabre

2 Answers

Pontiac Bonneville(2000) oil pressure sending unit


The oil pressure sending unit is located behind the oil filter, Threaded into an aluminunm housing. It has wiring that plugs into the sending unit. The oil filter has to be removed and you will need a deep well socket and a 6 inch extension. Change the oil and the sending unit together.

Jan 24, 2009 | 2000 Pontiac Bonneville

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

1 Answer

Low oil pressure


I believe your sending unit is located on the top of the block, towards the fire wall. You can get an inexpensive pressure test gauge and put in place of your sending unit. It should be a 1/4" NPT fitting. Does the pressure gauge fluctuate between low and high RPM? If so, chances are that your oil pump may need to be replaced.

Jun 29, 2008 | 1984 Chevrolet Camaro

Not finding what you are looking for?
2001 Pontiac Bonneville SSEi Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...