Question about Chrysler PT Cruiser

Open Question

2006 pt cruiser engine goes on and off...codes are P0882and P0700

My engine light goes on and off...Auto zone codes are P0082 and P0070

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fingaz22
  • 1068 Answers

SOURCE: 2001 pt cruiser engine light

well p0700 is a transmission code and the related repair on alldat is a error in tcm module! sounds like a bad computer but i couldn't say unless i tested it myself! sorry for lack of info and the other code was not in the list but there was a 1294 and that is a "target idle not reached" so i would be looking at the throttle body and clean it and make sure nothing is binding and aso vacume leaks throught the motor! good luck

Posted on Sep 20, 2009

  • 2 Answers

SOURCE: I have a 2008 pt cruiser. The engine light is on

My PT cruiser is a couple of years older, but I had the same problem. Drove fine, but start-up was erratic for several weeks. By the time  AAA arrived, it usually was working fine. But when it suddenly  started "struggling for power on the freeway and further along on the same trip, lurching (on a city avenue) I drove straight to my mechanic. It WAS the same sensor . . . and car has been driving perfectly ever since he changed it.

Posted on Mar 25, 2010

mcdevito75
  • 1970 Answers

SOURCE: I have a 2008 pt cruiser. The engine light is on

mcdevito75 here, Yes a crankshaft sensor could cause your mentioned problems, the sensor should be located near the Harmonic balancer, you may need a special tool to remove it and if I'm not mistaken the new sensor thakes an adjustment, Have auto zone change this sensor for you, even if you succeed, how often will you change this sensor.

Posted on Jul 09, 2010

  • 9 Answers

SOURCE: i have a 2004 PT Cruiser touring & 89,000

May need a new gas cap!

Posted on Feb 27, 2011

  • 66 Answers

SOURCE: my 2002 pt cruiser check

P0700 simply means there is a fault code present in the transmission module (TCM). P0740 Torque converter clutch circuit. This is usually caused by a worn out torque converter clutch which would involve replacing the torque converter and yes it would be expensive to repair if that is the cause. Diagnosis is usually made with a scanner and other equipment.

Posted on Apr 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Check engine light is on my 2006 pt cruiser


go have vehicle scanned most auto stores offer this service for free the code will advise you on what the problem is so repair can be made

Dec 16, 2016 | 2006 Chrysler PT Cruiser

1 Answer

Engine codes 0700/0882/0882pd


The p0700 is a code set to make the engine control module turn the service engine light on because there are fault codes stored in the transmission control module. The p0882 is for power input low to t.c.m. Check fuses and power and grounds to the powertrain control module.

Aug 02, 2015 | 2006 Chrysler PT Cruiser

2 Answers

Why check engine light comes on then starts to chug if speed reach 60 or accelerated


Have the problem code scanned for proper fix. You can go to advanced auto, Auto zone, ETC, they will scan vehicle as long as the light is on. For free! and tell you the problem code. It could be a cam or crank sensor that is going bad. Good-Day!

Aug 09, 2014 | 2006 Chrysler PT Cruiser

1 Answer

2002 PT Cruiser CRD 2.2 Engine management light is coming on the dash after you drive for about 10 or 15 mins If you leave the car for about 2 hours the engine management lights goes out the codes are...


Take your car to an auto parts store and ask them to put a code reader on your car. They not only tell you what the codes are (see below) but also the most likely cause and most likely solution. Or Go Look up OBDII Codes

I personally would start by buying throttle body cleaner and having them show you where to spray it.

Code 1511: Idle Switch (Electric Control Throttle)Circuit Malfunction

Code 0070: Outside air temperature sensor -circuit malfunction

Code 0015: Engine Coolant Temperature Circuit Malfunction


Code 0010: IAT Circuit Malfunction

Oct 24, 2013 | Chrysler PT Cruiser Cars & Trucks

1 Answer

My 2002 pt cruiser check engine light came on today i took it to auto zone they hooked up a computer and it came back with 2 codes wrong a p0700 and a p0740 what does this mean and is it expensive to fix


P0700 simply means there is a fault code present in the transmission module (TCM). P0740 Torque converter clutch circuit. This is usually caused by a worn out torque converter clutch which would involve replacing the torque converter and yes it would be expensive to repair if that is the cause. Diagnosis is usually made with a scanner and other equipment.

Apr 20, 2011 | 2002 Chrysler PT Cruiser

1 Answer

I have a 2008 pt cruiser. The engine light is on


mcdevito75 here, Yes a crankshaft sensor could cause your mentioned problems, the sensor should be located near the Harmonic balancer, you may need a special tool to remove it and if I'm not mistaken the new sensor thakes an adjustment, Have auto zone change this sensor for you, even if you succeed, how often will you change this sensor.

May 14, 2010 | 2005 Chrysler PT Cruiser

3 Answers

My engine light came on, can I continue to drive


As long as its not FLASHING it should be ok to drive, get it checked out ASAP though.

Nov 05, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Check engine light goes on for a few days and then resets itself


Sounds like a re-occuring temporary code....take it back to the dealer or Auto Zone and have the code scanned within your 6 start reset limit

Apr 01, 2009 | 2008 Chrysler Pt Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...