Question about 2006 Chrysler 300

Open Question

Crankshaft will not fully rotate on a 2006 chrysler 300 3.5L

Replaced the timing belt but did not set the timing marks correctly when i reinstalled the belt, now the crankshaft will not fully rotate

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 261 Answers

SOURCE: timing belt replacing

a diagram will help but let me give you a hint you dont need the diagram, once you remove the cover you will see 3 gears the top is the cam gear and if you look at the gear pulley there is a small hole set this at twelve o clock position, the distributor gear which is the middle one should be set in such a way that the rotor of the distributor alighn with number one on the dist cap and the third the last should be set to align the timing mark on the bell housing of the transmission and set it to zero, instal the belt and the car will run fine

Posted on Nov 15, 2008

  • 460 Answers

SOURCE: 1999 Chrysler 300m, how di I line up the timing

you cannot because the valves are bent, if the motor is a mitsubishi v 6 yu probably have holes in the tops of the pistons also.

Posted on Nov 07, 2009

  • 47 Answers

SOURCE: 2006 Chrysler Pacifica serpentine belt routing

here are a couple diagrams...
1e7d361.jpg

011a835.jpg

If you need anything else, let me know.

Posted on Mar 19, 2010

tunde007
  • 2382 Answers

SOURCE: Like to know where the

Hi, here you are...
39900a5.gif Crankshaft and camshaft alignment marks-2.4L (VIN X) Engine


9f5c6e9.gif
Camshaft and crankshaft alignment marks-Chrysler 2.5L (VIN N) engine


acb6bd1.gif
Timing belt engine sprocket timing-2.5L (VIN H) engine

Posted on Feb 13, 2011

chuckster57
  • 1102 Answers

SOURCE: i need a diagram for

I am guessing that you mean the timing marks for the timing belt. here is a picture:

chuckster57_30.gif

Posted on Apr 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt re-install and engine hard stops when rotating by hand even when timing marks lined up.


That hard stop is the valves hitting the head of the piston, you most likely have bent a valve, you have the valve timing wrong.

Sep 25, 2016 | 2006 Chrysler 300 Touring

1 Answer

I need the timing marks for belt replacement on the 1.6L SOHC 1990 Geo Prizm


1.6 engine, timing belt. 4A not 4AF. F = twin cam.
V.I.N. code 6 not 5, the 5is twin cam 4AFE twin.
the car is a Corolla, and as such info is easy to find on toys,
so that the engine real name is.
http://en.wikipedia.org/wiki/Toyota_A_engine#4A

so you dont want all the facts? marks and how to set tension correctly? really? at #12 and 18?
getting all this right, makes it GO 60k more miles, (a fact)

the words.
  1. Remove the timing belt covers using procedures described earlier in this section.
  2. If not done as part of the cover removal, rotate the crankshaft clockwise to the TDC/compression position for No. 1 cylinder.
  3. Loosen the timing belt idler pulley to relieve the tension on the belt, move the pulley away from the belt and temporarily tighten the bolt to hold it in the loose position.
  4. Make matchmarks on the belt and both pulleys showing the exact placement of the belt. Mark an arrow on the belt showing its direction of rotation.
  5. Carefully slip the timing belt off the pulleys.
  6. dont move cam, with belt off it warns.
  7. Remove the idler pulley bolt, pulley and return spring.
  8. Use an adjustable wrench mounted on the flats of the camshaft to hold the cam from moving. Loosen the center bolt in the camshaft timing pulley and remove the pulley.
  9. Check the timing belt carefully for any signs of cracking or deterioration. Pay particular attention to the area where each tooth or cog attaches to the backing of the belt. If the belt shows signs of damage, check the contact faces of the pulleys for possible burrs or scratches.
  10. Check the idler pulley by holding it in your hand and spinning it. It should rotate freely and quietly. Any sign of grinding or abnormal noise indicates replacement of the pulley.
  11. Check the free length of the tension spring. Correct length is 38.5mm measured at the inside faces of the hooks. A spring which has stretched during use will not apply the correct tension to the pulley; replace the spring.
  12. If you can test the tension of the spring, look for 8.4 lbs. of tension at 50mm of length. If in doubt, replace the spring.
  13. Reinstall the camshaft timing belt pulley, making sure the pulley fits properly on the shaft and that the timing marks align correctly. Tighten the center bolt to 43 ft. lbs.
  14. Before reinstalling the belt, double check that the crank and camshafts are exactly in their correct positions. The alignment mark on the end of the camshaft bearing cap should show through the small hole in the camshaft pulley and the small mark on the crankshaft timing belt pulley should align with the mark on the oil pump.
  15. Reinstall the timing belt idler pulley and the tension spring. Pry the pulley to the left as far as it will go and temporarily tighten the retaining bolt. This will hold the pulley in its loosest position.
  16. Install the timing belt, observing the matchmarks made earlier. Make sure the belt is fully and squarely seated on the upper and lower pulleys.
  17. Loosen the retaining bolt for the timing belt idler pulley and allow it to tension the belt.
  18. Temporarily install the crankshaft pulley bolt and turn the crank clockwise 2 full revolutions from TDC to TDC. Insure that each timing mark realigns exactly.
  19. Tighten the timing belt idler pulley retaining bolt to 27 ft. lbs.
  20. Measure the timing belt deflection (Tool 23600 B or similar), looking for 5-6mm of deflection at 4.4 pounds of pressure. If the deflection is not correct, readjust the idler pulley by repeating steps 15 through 18.
  21. Remove the bolt from the end of the crankshaft.
  22. Install the timing belt guide onto the crankshaft and install the lower timing belt cover.
  23. Continue reassembly of the timing belt covers as outlined previously in this section.


25607983-3uasjzd4mulxtskqjlrmltjn-4-0.jpg

Mar 26, 2015 | 1990 Geo Prizm

1 Answer

Can the crankshaft position sensor on a 2006 chrysler 300 3.5L prevent the crankshaft from fully rotating?


Why are you asking that question?

You know if the timing belt,crank & cam gears are not set correctly,
that the valves will hit the pistons & the motor won't turn

Mar 25, 2014 | 2006 Chrysler 300

1 Answer

If the water pump is installed will the timing have to be reset



Removal & Installation

2.5L (VIN H) Engine

  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with a insulator grommet which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Remove the right inner splash-shield.
  3. Remove the accessory drive belts.
  4. Remove the crankshaft damper.
  5. Remove the right engine mount.
  6. Place a suitable floor jack under the vehicle to support the engine.
  7. Remove the right engine mount bracket.
  8. Remove the timing belt upper left cover, upper right cover and lower cover.
  9. Loosen the timing belt tensioner bolts.
    NOTE Before removing timing belt, be sure to align the sprocket timing marks to the timing marks on the rear timing belt cover.
  10. If the present timing belt is going to be reused, mark the running direction of the timing belt for installation. Remove the timing belt and the tensioner.
  11. Remove the camshaft timing belt sprockets from the camshaft, if necessary.
  12. Remove the crankshaft timing belt sprocket and key.
  13. Place the tensioner into a soft-jawed vise to compress the tensioner.
  14. After compressing the tensioner place a pin into the plunger side hole to retain the plunger until installation.

    0996b43f80208cc8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt engine sprocket timing-2.5L (VIN H) Engine


To install:
  1. If removed, reinstall the camshaft sprockets onto the camshaft. Install the camshaft sprocket bolt and tighten to 65 ft. lbs. (88 Nm).
  2. If removed, reinstall the crankshaft timing belt sprocket and key onto the crankshaft.
  3. Set the crankshaft sprocket to Top Dead Center (TDC) by aligning the notch on the sprocket with the arrow on the oil pump housing, then back off the sprocket three notches before TDC.
  4. Set the camshafts to align the timing marks on the sprockets with the marks on the rear timing belt cover.
  5. Install the belt on the rear camshaft sprocket first.
  6. Install a binder clip on the belt to the sprocket so it won't slip out of position.
  7. Keeping the belt taut, install it under the water pump pulley and around the front camshaft sprocket.
  8. Install a binder on the front sprocket and belt.
  9. Rotate the crankshaft to TDC.
  10. Continue routing the belt by the idler pulley and around the crankshaft sprocket to the tensioner pulley.
  11. Move the crankshaft sprocket clockwise to TDC to take up the belt slack. Check that all timing marks are in alignment.
  12. Reinstall the tensioner to the block but do not tighten it at this time.
  13. Using special tool No. MD998767 and a torque wrench on the tensioner pulley, apply 39 inch lbs. (4.4 Nm) of torque to the tensioner. Tighten the tensioner pulley bolt to 35 ft. lbs. (48 Nm).
  14. With torque being applied to the tensioner pulley, move the tensioner up against the tensioner bracket and tighten the fasteners to 17 ft. lbs. (23 Nm).
  15. Remove the tensioner plunger pin, the tension is correct when the plunger pin can be removed and replaced easily.
  16. Rotate the crankshaft two revolutions clockwise and recheck the timing marks. Check to be sure the tensioner plunger pin can be easily installed and removed. If the pin does not remove and install easily, perform the procedure again.
  17. Reinstall the timing belt cover.
  18. Reinstall the engine mount bracket.
  19. Reinstall the right engine mount.
  20. Remove the engine support.
  21. Install the crankshaft damper and tighten to 134 ft. lbs. (182 Nm).
  22. Reinstall the accessory drive belts and adjust them.
  23. Reinstall the right inner splash-shield.
  24. Perform the crankshaft and camshaft relearn alignment procedure using the DRB scan tool or equivalent.

2.5L (VIN N) Engine
  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts.
  3. Using Crankshaft Holding Tools MB990767 and MB998754, remove the crankshaft bolt and remove the pulley.
  4. Remove the heated oxygen sensor connection.
  5. Remove the power steering pump with the hose attached and position it aside.
  6. Remove the power steering pump bracket.
  7. Place a floor jack under the engine oil pan, with a block of wood in between, and raise the engine so that the weight of the engine is no longer being applied to the engine support bracket.
  8. Remove the upper engine mount. Spraying lubricant, slowly remove the reamer (alignment) bolt and remaining bolts and remove the engine support bracket.
    NOTE The reamer bolt is sometimes heat-seized on the engine support bracket.
  9. Remove the front timing belt covers.
  10. If the timing belt is to be reused, draw an arrow indicating the direction of rotation on the back of the belt for reinstallation.
  11. Align the timing marks by turning the crankshaft with MD998769 Crankshaft Turning tool. Loosen the center bolt on the timing belt tensioner pulley and remove the belt.
    WARNING Do not rotate the crankshaft or camshaft after removing the timing belt or valvetrain components may be damaged. Always align the timing marks before removing the timing belt.
  12. Check the belt tensioner for leaks and check the pushrod for cracks.
  13. If the timing belt tensioner is to be replaced, remove the retaining bolts and remove the timing belt tensioner. When the timing belt tensioner is removed from the engine, it is necessary to compress the plunger into the tensioner body.
  14. Place the tensioner in a vise and slowly compress the plunger. Take care not to damage the pushrod.
    NOTE Position the tensioner in the vise the same way it will be installed on the engine. This is to ensure proper pin orientation for when the tensioner is installed on the engine.
  15. When the plunger is compressed into the tensioner body, install a pin through the body and plunger to hold the plunger in place until the tensioner is installed.

    0996b43f80208cbb.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Camshaft and crankshaft alignment marks-Chrysler 2.5L (VIN N) engines


To install:
  1. Install the timing belt tensioner and tighten the retaining bolts to 17 ft. lbs. (24 Nm), but do not remove the pin at this time.
  2. Check that all timing marks are still aligned.
  3. Use bulldog clips (large paper binder clips) or other suitable tool to secure the timing belt and to prevent it from slacking. Install the timing belt. Starting at the crankshaft, go around the idler pulley, then the front camshaft sprocket, the water pump pulley, the rear camshaft sprocket and the tensioner pulley.
  4. Be sure the belt is tight between the crankshaft and front camshaft sprocket, between the camshaft sprockets and the water pump. Gently raise the tensioner pulley, so that the belt does not sag, and temporarily tighten the center bolt.
  5. Move the crankshaft 1 / 4 turn counterclockwise, then turn it clockwise to the position where the timing marks are aligned.
  6. Loosen the center bolt of the tensioner pulley. Using MD998767 tensioner tool, and a torque wrench apply 3.3 ft. lbs. (4.4 Nm) tensional torque to the timing belt and tighten the center bolt to 35 ft. lbs. (48 Nm). When tightening the bolt, be sure that the tensioner pulley shaft does not rotate with the bolt.
  7. Remove the tensioner plunger pin. Pretension is correct when the pin can be removed and installed easily. If the pin cannot be easily removed and installed it is still satisfactory as long as it is within its standard value.
  8. Check that the tensioner pushrod is within the standard value. When the tensioner is engaged the pushrod should measure 0.149-0.177 in. (3.8-4.5mm).
  9. Rotate the crankshaft two revolutions and check the timing marks. If the timing marks are not properly aligned remove the belt and repeat Steps 17 through 23.
  10. Install the timing belt covers.
  11. Install the engine mounting bracket.
  12. Lower the engine enough to install the engine mount onto bracket and remove the floor jack.
  13. Install the power steering pump bracket and pump.
  14. Install the crankshaft pulley and tighten the retaining bolt to 13 ft. lbs. (18 Nm).
  15. Install the accessory drive belts.
  16. Properly fill the cooling system.
  17. Connect the negative battery cable.
  18. Check for leaks and proper engine and cooling system operation.

May 22, 2012 | 1999 Chrysler 300M

1 Answer

Resetting timing after replacing head gasket


Do you have the timing belt on and the tensioner set correct? If so, just rotate the crankshaft around until the notch on the crank sprocket is lined up with the pointer on the oil puimp housing (TDC). Now the camshaft sprocket's notch or pointer should be at the top and exactly in line with the mark on the rear timing belt cover. If it's not correct, you'll have to release tension on the belt, remove it, and set the camshaft to the mark. But before you do that, turn the crankshaft back (counterclockwise) just three notches. Then you can turn the cam to line up, then return crank to line up, and continue with belt installation, setting the tension, and re-checking timing marks after rotating the crankshaft a couple of revolutions. Once you know the timing is set to TDC, no further timing adjustments are possible, because the computer controls timing. I don't know how important it is, but just to let you know: Chrysler recommends after belt removal or replacement that one perform the "crankshaft and camshaft relearn alignment procedure" using the DRB scan tool (Chrysler's scanner device) or equivalent scan tool.
And the firing order on all four cylinder engines is the same: 1 3 4 2.
I hope this helps you out. Cheers.

May 11, 2012 | 1996 Plymouth Breeze

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

2 Answers

Timing belt alignment


A factory service manual would help, but I'm assuming that if you had one, you probably wouldn't be on this site.

To set the timing, you need to first perform the obvious: remove the accessory drive belts, cam pulley covers, and engine fan and hub. Next you'll need to rotate the engine by hand until the timing marks on the camshaft sprockets and crankshaft are aligned with their corresponding stationary marks. The 0 degree mark on the lower timing belt cover is the timing mark for the crankshaft pulley. There is a mark (small, vertical formed indentation) for the left camshaft pulley on the backing plate behind the pulley near the 1 o` clock position. The same mark exists for the right camshaft pulley only it is on the backing plate near the 8 o`clock position (making it difficult to see). With the crankshaft placed at the zero mark, you can observed where the timing discrepancy exists.

(TIP: Once the right camshaft timing is properly lined up, etch an additional mark on the pulley's face and the backing plate at the 12 o`clock position. This will make it easier to align the pulley for furture adjustments and repairs)

To set the timing correctly, move the crankshaft pulley to 12 deg. BTDC. Being careful to not disturb the position of the crankshaft once it has been moved to that position, remove the crankshaft pulley, lower timing belt cover, timing belt tensioner, and timing belt. Compress the timing belt tensioner and if the original ring pin isn't available to retain the tensioner a small allen wrench can be used to achieve the same results. Line up both camshaft marks and reinstall the timing belt and timing belt tensioner (do not remove the timing belt tensioner tool used to maintain the tensioner piston in a compressed position). When installing the timing belt, be sure to allow the least amount of slack to exisit between the left camshaft pulley and the crankshaft sprocket, but without moving the pulleys.

Next, remove the timing belt tensioner piston retention tool and mount the lower timing belt cover and crankshaft pulley (without fully installing them). Rotate the crankshaft pulley to the 0 deg. mark. If done correctly, moving the crankshaft pulley from 12 deg. BTDC to 0 deg. will remove all remaining slack from the timing belt assembly and the camshaft pulleys and crankshaft pulleys will be lined up with their corresponding marks. Once proper timing has been achieved, install all removed parts.

(Another TIP: I hope it's not necessary, but in case it is, I'll remind you that proper torque of all bolts are necessary as this is an all aluminum engine. Stripping out bolts holes due to over-tightening bolts occurs very easily and become very annoying to deal with [e.g. alternator belts not being able to be tightened completely and constantly squealing every few days, etc.])

Apr 26, 2009 | 1997 Isuzu Rodeo

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

1 Answer

Cant set timing on 1991 nissan maxima


The marks are for an initial reference only. Once the belt is correctly in place and proper tension set, the cam is in time with the crankshaft and will stay that way until the belt breaks or slips from one cog to the next (won't happen if the tension is correct).

After the belt is initially set with the marks lined up, two rotations of the crankshaft (one rotation of the camshaft) will have the marks in a different place. The only exception would be if the belt had an exact multiple of ribs/teeth compared to the crankshaft, and that is not very likely.

Mar 23, 2009 | 1990 Nissan Maxima

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
2006 Chrysler 300 Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...