Question about Ford F

Open Question

How to remove the rear axle on a 1964 ford f600

F600 cannot remove the cones from the axle to hub assembey

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: ford f350 drum brake

Don't listen to the last guy. The drum does not just slide off. You have to remove the axle by removing the eight 5/8" bolts and pulling it out. Inside the hub you will find a ratcheting lock nut. Visible will be 4 slots where a special socket fits. You can buy the socket from a parts store or you can just use a 1/4" punch and slowly hammer to slowly thread the nut off. Drivers side is left hand thread while the passenger side is right hand thread. Remove the nut and the outer bearing will fall out (so catch it before it hits the dirt). Then slide the drum off. While you inside there it is a good idea to replace the axle seal. It's about $30 and an easy change.

Posted on Apr 19, 2009

Ad
ourhowse
  • 2007 Answers

SOURCE: removal of axle 1997 ford explorer awd

You have to take the rear differential apart, and then pull the axle.

Posted on May 05, 2009

  • 3 Answers

SOURCE: Noise in front axle when I lock my hubs on an 1988 Ford F-150

i would bet you need to replace your locking hubs

Posted on Jul 30, 2009

REDOIL
  • 355 Answers

SOURCE: How do I remove the rear axles on my 2000 GMC

well you need to pull rear cover and pull rotors or drums off and there are two clips in side the diff but you need to pull the center shaft out AND PUSH THE SHAFT IN WORD AND REMOVE TWO CLIPS AXLE WILL SLIDE OUT

Posted on Aug 13, 2009

REDOIL
  • 355 Answers

SOURCE: I have a 2003 Ford f250 heavy duty 5.4l.On the

WELL IF YOU HAVE FULL FLOATER TYP REAR END THEN YOU UBOLT CENTER HUP PULL AXLE AND YOU WILL SEE ADJUSTER NUT SHUOLD NOT BE TO TIGHT OR YOU WILL CAUSE BEARING TO WEAR OUT FAST YOU JUST SNUG THE NUT SPIN THE HUB MAKE SHERE IT TRUNS SMOOTH

Posted on Aug 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change rear wheel bearings in my 2010 ford bantam rocam? Must the nut be very tight?


adjust the brakes back off so that the drum can be pulled off first
next remove the grease cap, and split pin
remove the tin nut and the axle nut
pull the hub off the axle
replace the bearings after repacking the cones correctly ( grease between rollers under the cage )
reinstall making sure that the grease seal lip is facing the bearings
install the hub back on the axle and install the nut
do it up until it touches the bearing , spin the hub and do it up a bit more while turning
This ensures that all the tapered rollers are seated correctly
Now without touching any thing undo the nut then do it back up until it touches the bearing again
This is a no pre-load - no end float position that is desirable for the bearing
fit the tin nut positing it so that the split pin can go through the axle hole. If after many changes of position of the tin nut you still cannot get a section to line up with the hole , adjust the axle nut up just a bit until something lines up
any more than one castleantion hole will be too tight .
fit grease cap without filling with grease as that grease will do nothing
what you have put between the rollers under the cage will,be sufficient

Dec 30, 2015 | Ford Cars & Trucks

1 Answer

How do you remove the rear axle or hub on a 1990 f700


Remove the nuts holding the axle to the hub. remove the lock washers. Hit the center of the axle with a 10lbs or 20lbs sledge hammer (careful not to hit axle studs) to break it free. Take a small screw driver and work wedged split cones between axle and axle studs out. Then axle can be removed.

Apr 30, 2015 | Ford Cars & Trucks

1 Answer

How to fit front wheel bearings Which brand to use for quality


If the car is front wheel drive a puller is required to dismantle the hub a rather involved job better left to a mechanic .If rear wheel drive do the following. ( Applies to front wheel drive also.) Chock rear wheels,loosen front wheel nuts, jack up car, fit safety stands,remove wheel , remove grease cap from axle. remove split pin or locking nut on axle ,Remove hub, with a punch drive out the grease seal ,the tapered cone bearings can now be removed, the 2 bearing cups still in the housing will have to be pressed out ,all old grease has to be cleaned out. the new cones must be repacked with high temp bearing grease . tap in the seal with the lip facing inwards , slide on the hub fit the outer cone to the axle , the spacer and nut goes on next, tighten the nut to seat the bearings , spin the hub make sure its free to spin, back off the nut one eighth of a turn fit a new split pin or lock tab. fit grease cap and road wheel.

Jul 27, 2014 | Cars & Trucks

1 Answer

Need to remove the rear axles on a 1964 ford ranchero 8 inch rear end


Jack and suppoet with stands, put vehicle in neutral, ensure emergency brake is off. remove rear wheels, remove drums, you will see a hole in the axle end to fit a socket to undo 4 nuts, if you don't have a slide hammer, put wheel on without drum and get underneath and kick wheel. U must make sure the car will not fall, better safe than sorry. {you shouldn't have to remove brakes} good luck

Oct 20, 2013 | Ford Cars & Trucks

1 Answer

How to take of lefthand bearing and replace bearing to econovan 1999 ford


I take it that the van is a rear wheel drive. So remove the wheel. Remove the brake caliper and lift off the disc. Undo the axle nut and remove hub from axle. Knock out both the bearing cups and clean hub center. Fit new cups into the hub ensuring they are tight against the seat. Thaking a small amount of grease in the palm of you hand take the cone and with the most open area tend to scrape the grease from you palm so that the grease is forced between the rollers until it come out the smallest end.This grease is all thaty you will need for a properly lubricated bearing. Spread grease evenly around the outside of the rollers. Fit inner cone into hub and tap in new grease seal (lip facing bearing) Having repeated lubricating process on outer cone fit hub back on axle and fit outer cone. Fitflat washer and nut . Do nut up while turning hub so as to seat bearings. Tighten nut until a slight drag is felt when turning the hub. Now comes the difficult part. Without touching the hub undo the nut until it is slightly loose then do it back up until it just touches the bearing. THis is a no preload -no freeplay position for the bearing. Having achieved this, pin the nut . IF it is necessary to turn the nut to allow this to happen tighten the nut slightly. Refit dust cap ,calpier, wheel etc REmember to replace both bearings cups and cones and use high temp grease Safety first --place the vehiocle in stands--- not bricks

Mar 07, 2013 | Cars & Trucks

1 Answer

How remove rear axle for 2001 isuzu npr


remove the eight nuts and cones in the center, (if the cones don't come out hit the center with a dead blow hammer and the shock will loosen them) put a drip pan under the hub and slide the axel out.

Nov 01, 2012 | Cars & Trucks

1 Answer

How to replace rear wheel hub


Sodium based grease is not compatible with lithium based grease. Do not lubricate the wheel bearings without first thoroughly cleaning all old grease from the bearing. Use of incompatible bearing lubricants could result in premature lubricant breakdown.
  1. Raise and support the vehicle safely.
  2. Remove the wheels.
  3. Remove the brake drum or brake disc.
  4. Remove the hub grease cap.
  5. Remove the cotter pin retainer, adjusting nut and flatwasher from the rear wheel spindle. Discard the cotter pin.
  6. Remove the outer bearing and cone assembly.
  7. Remove the rear hub from rear wheel spindle.
  8. Using Seal Remover (TOOL-1175-AC) or equivalent, remove and discard the oil seal.
  9. Remove the inner bearing cone and roller assembly.
  10. Clean the inner and outer bearing cups with solvent. Inspect the bearing cups for scratches, pits, excessive wear and other damage. If the bearing cups are worn or damaged, remove them using a Bearing Cup Puller (T77F-1102A) or equivalent.
To install:
  1. Throughly clean old grease from the surrounding surfaces. If a new hub assembly is being installed, remove the protective coating using degreaser.
  2. If the inner or outer bearing cups were removed, install replacement cups using Bearing Cup Replacer (T73-1202-A) or equivalent. Seat the cups properly in the hub.
If a bearing packer is not available, work as much grease as possible between the rollers and cages. Grease the cone surfaces.
  1. Using a bearing packer, pack the bearing cone and roller assemblies with a premium bearing grease.
  2. Place inner bearing cone and roller assembly in the inner cup. A light film of grease should be included between the lips of the new grease retainer.
  3. Install the retainer with Hub Seal Replacer (T83T-1175-B) or equivalent. Be sure the retainer is properly seated.
Keep the hub centered on the spindle to prevent damage to the retainer and spindle threads.
  1. Install the hub assembly on the spindle.
  2. Install the outer bearing cone and roller assembly on the spindle.
  3. Install the flat washer and nut. Tighten the nut to 18-23 ft. lbs. (24-31 Nm) while rotating the hub to set the end-play. Back off the nut and retighten to 18 inch lbs. (2 Nm).
  4. Install the new cotter pin.
  5. Install hub grease cap.
  6. Install brake drum or disc.
  7. Install the wheels.
  8. Lower the vehicle.

May 04, 2010 | 1998 Ford Windstar

1 Answer

How to install wheel bearing hub assemble (front)1998 on a ford escort


front or rear?

Assuming rear, on the brake drum:

Hub Removal
  1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
  1. Remove the wheel hub.
    1. Unstake the rear axle wheel hub retainer.
    1. Remove the rear axle wheel hub retainer and discard.
    1. Remove the wheel hub (1104).

Nov 05, 2009 | 1998 Ford Escort

1 Answer

Rear hubs


In the center of the hub is the axle retaining bolts, 8 I think, remove them and pull the axle out, under that is a giant nut that retains the hub, it requires a quite expensive special tool to remove and re-install correctly, that huge nut retains the entire hub/brake drum assembly. Replace th grease seal and check the axle bearing while you have it apart.


Please rate this solution.

Oct 19, 2008 | 2001 Ford F350 Super Duty SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...