Question about Jaguar X-Type

1 Answer

X type drivers door handle removal

X type door handle removal

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jaguar Master
  • 75,235 Answers

What year?

Posted on Mar 25, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removal of door actuator on my x type


easy, remove door panel,remove damp shield, antitheft shield. if drivers door. 1 screw 2 clips. remove ext.door handle. 2 torx screws, disconnect link rods, remove latch fixings edge of door, disconnect wiring, remove latch, if the prob is door not opening from outside there is a stronger ext. handle link rod availiable to rectify this problem, if rear door you may have to remove quarterlight/ window frame, the glass runner is in the way

Mar 16, 2014 | Jaguar Cars & Trucks

1 Answer

2002 Chevy Tracker ZR2 (small suv) outside, left, drivers door handle broke


You should have someone experienced with you to do this type of job, due to the complex series of tasks involved

Mar 04, 2013 | Cars & Trucks

1 Answer

Door will not open 2002 x type jaguar


The cable that goes to the inside door handle has fallen off, you have to remove the inner panel and look at the back of the handle, you should see a cable, most likely the cable fell off the retaining slot. Just push it back on until it bottoms out and replace the panel. This is common with door slamming, on x-types.

May 25, 2012 | 2002 Jaguar X-Type

1 Answer

I need to replce the drivers side mirror. Just seeking instructions on how to.


Remove front door handle bezel screw cover Remove inside handle bezel screw Remove inside handle bezel Lift upward on the rear of the front door inside handle bezel Disconnect electrical connector Remove handle screw cover
Remove handle screw Remove door trim panel upper screw Remove door trim panel lower screw Remove door trim panel (pull the door trim panel outward to release the pin-type retainers)Remove front door sail panel
Disconnect mirror electrical connector Remove 3 exterior mirror nuts and exterior mirror

agentyoel_0.png

Mar 07, 2011 | 2009 Ford Fusion

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

How to fix door handle on chevrolet cobalt 2008


Have to remove inner door panel and is usually 2 bolts around 10mm that hold handle in, but the rods must be removed first and these rods are only held in place by a spring steel clip that just flips out off the rod at the handle end.
To remove door panel - look for visible screws under and around the edges and or handles, remove all these. If window is winding type a horse-shoe clip holds the handle on and can be pushed off with a screw-driver if you push the panel away from handle and look behind the handle.
Then take a putty knife and or butter knives and insert between door and panel to pop plastic clips from door then lift on panel to remove from window jam.  Be careful of wires and plugs after this.  Remove plug clips and place panel aside.  Remove plastic and sound-proofing if any in the corner near the handle and a 10mm 1/4" drive ratchet to remove bolts on each side of handle.
This is a general answer but should work for the Cobalt as well.
East Coast Canada Rocks!!
:))

Jun 09, 2010 | 2008 Chevrolet Cobalt

1 Answer

Driver side door handle (outside) and gas pedal 2000 Camry


Bring the vehicle into the dealer if you have a sticky gas pedal. This is a TOYOTA PROBLEM.
Door handle:
It easy ! You need a philips2_bing.gif and flat screw driver,and a needle nose pliar.
Use flat screw driver and pry out the two or three dust covers for the arm rest screws then use philips and remove the screws. Next use the flat screw driver and pry out the black plastic mirror cover from the inside of the door. Pry out the switch with the flat screw driver and disconnect it. On the side of the door panel just above the striker/loch mechanism is this plastic push pull type of a hold in screw. Use flat screw driver to get it to move a little then pull it out with the needle nose. Depending on which door your doing if you have a map folder in the door there are two more screw to remove on the bottom of the door.
Now the inside door handle is tricky it comes out in TWO pieces. Use philips and get the only hold down screw you see out.( you may have to pry out a little screw cover first) Now the inside door handle cover is removed by placeing the flat screw driver on the rear of the outside of the cover top and on the outside rear bottom to release the tangs that are holding it onto the panel.Pry it out lightly you may have to place the screw driver over the top of the door release button and pry that way. Don't loose your cool its a pain but it will fall out. Once its removed unhook the panel.

Next lift the plastic cover and remove the door handle hooks and levers . Basically use common sense this is easy stuff. There may be two screws from inside of door panel that keep handle in place . Then work handle loose from outside and inside . reverse for installation.

Jan 27, 2010 | 2000 Toyota Camry

1 Answer

How do i remove the drivers side door panel on a jag s type


This is the same front or rear door. 1. remove rubber insert at the bottom of the arm rest/door handle 2. remove the 2. philip head screws. 3. run hand along bottom edge of door panel to ensure no other securing screws. 4. starting at the top rear edge of the door panel side a large flat screw drive/door panel tool(what ever you have) 5. lift sharply and you will here poping noises fromt the push clips lifting out of the socket. 6. as you work down the rear edge of the door panel you will see the trim around the interior door handle lift away. remove it. 7. the interior door handle will remain on the door. 8. remove the rest of the door panel.

Oct 10, 2009 | 2000 Jaguar S-Type

1 Answer

How to remove door panel to gain access w/out damaging panel?


I hope this helps , easier done than said :)
1- Remove door latch bezel. (handle) 2- You will find door trim panel retaining bolt , remove it. 3- Remove the door pull handle screw cover. 4- Remove the door pull handle retaining screws. 5- Detach the interior door trim panel ( to make removal easy , release clip by lowering glass and pressing case inwords) 6- Disconnect the door trim harness electrical connector. 7- Remove the door trim. 8- Disconnect the driver door module electrical connector 9- To install , reverse removal procedures

Jul 29, 2009 | 2000 Jaguar S-Type

1 Answer

The drivers door [R/H side], inside handle has stopped opening door. the handle is still firm and pivots perfectly but i have to reach outside and open from handle on exterior of car. Is it a simple re...


Im not sure about the hardware on this particular car, but all cars have a rod linking the inside handle to the doorlock, attacked on both ends by a type of plastic clip. When it breaks the rod simply slips out and the door handle will move idly when operated, not opening the door. You will have to remove your door panel carefully and remove the handle to inspect the mechanism. If it is the clips, they should be easily available at your autoparts store.

Jun 04, 2008 | 1992 Audi 100

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...