Question about 2002 Chrysler Sebring

Open Question

Timing alignment on a 2.7 DOHC

I can't align all the timing marks.Can't see them with the chain on

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 323 Answers

SOURCE: How do I set the DOHC's timing on a 2000 Chrysler Concorde 2.7?

There should be plated links on those chains too. There is an index dot in both cams on each head that set at the twelve o'clock position.

Posted on Jun 09, 2009

motor1258
  • 6674 Answers

SOURCE: im having trouble aligning the timing belt with

The dot on camshaft(s) goes between the 2 on cover behind it. The one on crankshaft aligns with TDC indicator just above it. Maybe this will help. It is a 3.5L, dual cam?659f53a.gif

Posted on Nov 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

2 Answers

How do you fix the timing on the timing chain


I have a 2.2 single cam where are the marks on the gears

Aug 21, 2012 | 2004 Pontiac Sunfire

1 Answer

Need the timing marks for a 2000 alero


please let me know if you have questions.
2.4L Engine
NOTE It is recommended that the entire procedure be reviewed before attempting to service the timing chain.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following: Negative battery cable, Coolant surge tank, Accessory drive belt, Alternator
  4. Install an engine support.
  5. Remove or disconnect the following: Upper cover fasteners, Front cover vent hose, Right engine mount and bracket, Right front wheel, Right lower splash shield, Crankshaft balancer, Lower cover fasteners, Front cover
  6. Rotate the crankshaft clockwise, as viewed from front of engine (normal rotation) until the camshaft sprocket's timing dowel pin holes align with the timing chain housing holes. The crankshaft sprocket mark should align with the engine mark. The crankshaft sprocket keyway should point upward and align with the cylinder bores centerline. This is the normal timed position.
  7. Remove the timing chain guides.
  8. Remove the timing chain tensioner.
    NOTE Be sure all the slack in the timing chain is above the tensioner assembly when removing it. CAUTION The tensioner plunger is spring loaded and could fly out causing personal injury.
  9. Remove or disconnect the following: Timing chain, Camshaft sprockets

To install:
  1. Install or connect the following: Camshaft sprockets. Torque the bolts to 52 ft. lbs. (70 Nm),
    Camshaft sprocket alignment pin through the camshaft sprockets holes into the timing chain housing holes to position the camshafts for timing.
  2. If the camshafts are out of position and must be rotated more than 1 / 8 turn in order to install the alignment dowel pins, perform the following:
    1. Rotated the crankshaft 90 degrees clockwise off Top Dead Center (TDC) in order to give the valves adequate clearance to open.
    2. Once the camshafts are positioned and the dowels installed, rotate the crankshaft counterclockwise back to TDC.
      WARNING Do not rotate the crankshaft clockwise to TDC or valve and piston damage may occur.
  3. Install the timing chain over the exhaust camshaft sprocket, around the idler sprocket and around the crankshaft sprocket.
    jturcotte_2361.gifjturcotte_2362.gif

    Fig. Timing chain and sprocket alignment positions-2.4L DOHC engine

  4. Remove the alignment dowel pin from the intake camshaft. Using a dowel pin remover tool, rotate the intake camshaft sprocket counterclockwise enough to slide the timing chain over the intake camshaft sprocket. Release the camshaft sprocket wrench. The length of chain between the 2 camshaft sprockets will tighten.
    NOTE If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated.
  5. Leave the alignment dowel pins installed.
  6. With slack removed from chain between intake camshaft sprocket and crankshaft sprocket, the timing marks on the crankshaft and the cylinder block should be aligned. If marks are not aligned, move the chain 1 tooth forward or rearward, remove slack and recheck the marks.
  7. Tighten the chain housing to engine stud. The stud is installed under the timing chain. Torque it to 19 ft. lbs. (26 Nm).
  8. Reload the timing chain tensioner as follows:
    1. Form a keeper from heavy gauge wire.
    2. Slightly, compress the shoe plunger and insert a small screwdriver into the access hole.
    3. Release the ratchet pawl and compress the plunger completely into the hole.
    4. Insert the keeper between the access hole and the blade.
  9. Install or connect the following:
    Tensioner assembly to the chain housing. Torque the bolts to 89 inch lbs. (10 Nm). Tensioner shoe and retainer. Torque the bolts to 89 inch lbs. (10 Nm). NOTE Recheck plunger assembly installation. It is correctly installed when the long end is toward the crankshaft.
  10. Remove the alignment dowel pins. Rotate crankshaft clockwise 2 full rotations. Align the crankshaft timing mark with mark on cylinder block and reinstall alignment dowel pins. Alignment dowel pins will slide in easily if engine is timed correctly.
    WARNING If the engine is not correctly timed, severe engine damage could occur.
  11. Install or connect the following: Timing chain guides, New seal into the front cover by lubricating the seal lip and tapping it into place, Front cover and gaskets. Torque the nuts and bolts to 106 inch lbs. (12 Nm), Crankshaft balancer. Torque the bolt to 129 ft. lbs. (175 Nm), Right front lower splash shield, Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm), Right engine mount bracket. Torque the bolts to 81 ft. lbs. (110 Nm) plus an additional 90 degree turn, Right engine mount. Torque the bolt to 49 ft. lbs. (60 Nm), Upper cover vent hose
  12. Remove the engine support.
  13. Install or connect the following: Alternator. Torque the bolts to 37 ft. lbs. (50 Nm), Accessory drive belt, Coolant surge tank, Negative battery cable.
  14. Refill the cooling system.
  15. Start the engine and check for leaks.

Oct 04, 2011 | Cars & Trucks

1 Answer

Dont no how to set the timming and what it suppose to be


Timing Chain and Sprockets
REMOVAL & INSTALLATION




  1. Fig. 1: At 90 degrees past TDC, the crankshaft sprocket timing
    mark and keyway will align with the main bearing cap split line
    84193100.gif






    Fig. 2: Exploded view of the timing chain and sprocket
    assembly - SOHC engine
    84193101.gif






    Fig. 3: Insert the timing pin to ensure that the camshaft is at
    No. 1 TDC - SOHC engine
    84193102.gif






    Fig. 4: When the camshaft is at TDC, rotate the crankshaft
    counterclockwise 90 degrees to achieve TDC
    84193103.gif


DOHC Engine

  1. Disconnect the negative battery cable.
  2. Remove the timing chain front cover.
    NOTE: During timing chain and sprocket removal, position the
    crankshaft 90 degrees past Top Dead Center (TDC) to make sure the pistons will
    not contact the valves upon assembly.



  3. Carefully rotate the crankshaft clockwise so the timing mark on the
    crankshaft sprocket and keyway align with the main bearing cap split line.
  4. Remove the bolts, then remove the timing guides and tensioner.
  5. Remove the camshaft sprocket bolts, using a 7?8 in. (21mm) wrench
    to hold the camshaft. Then remove the timing chain and camshaft sprocket. Remove
    the crankshaft sprocket, if necessary.
    To install:

  6. Inspect the chain for wear and damage. Check the inside diameter of the
    chain, it should be no more than 23.15 in. (588mm). Inspect the chain guides for
    wear or cracks and the timing sprockets for teeth or key wear. Replace
    components as necessary.
  7. Verify that the crankshaft is positioned 90 degrees clockwise past TDC. The
    crankshaft keyway should be at 3 o'clock aligned with the main bearing cap split
    line to prevent piston and valve damage.
  8. Install the camshaft sprockets, retaining bolts and washers. Make sure the
    letters FRT on the sprockets face forward, away from the cylinder block. Use the
    wrench flats provided on the camshafts to hold the shaft and tighten the bolts
    to 75 ft. lbs. (102 Nm).
  9. Bring the camshafts up to No. 1 TDC by rotating the camshafts and sprocket
    until the dowel pins are at 12 o'clock. Install a 1?6 in. drill bit
    into the hole in the sprocket about 9 o'clock.
  10. If removed, install the crankshaft sprocket, then rotate the crankshaft
    counterclockwise 90 degree up to No. 1 TDC (keyway and sprocket timing mark at
    12 o'clock, in alignment with the block timing mark).
  11. Position the timing chain under the crankshaft sprocket and over the
    camshaft sprockets so 2 silver link plates align with the reference marks on the
    camshaft sprockets and another 2 plates align with the downward tooth (at 6
    o'clock position) on the crankshaft sprocket. Excess chain slack should be
    located on the tensioner side of the cylinder block.
  12. Verify that the crankshaft reference mark aligns with the cylinder block
    mark at 12 o'clock and that the timing pins are installed in the holes at about
    the 9 o'clock position. Remove the timing pins from the camshaft sprockets.
  13. Install the timing chain fixed guide to the right of the block face toward
    the water pump. Tighten the bolts to 21 ft. lbs. (28 Nm) and verify the chain is
    snug against the guide.
  14. Install the pivoting chain guide and check for clearance between the block
    and head. Tighten the bolt to 19 ft. lbs. (26 Nm) and verify the guide pivots
    freely.
  15. Install the 2 forward camshaft bearing caps and the upper timing chain
    guide, then tighten the retaining bolts to 124 inch lbs. (14 Nm).
  16. Retract the tensioner plunger and pin the ratchet lever using a 1?8 in. (3.18mm) No.
    31 drill bit inserted in the alignment hole at the lower front of the component.
    Install the tensioner and tighten the bolts to 14 ft. lbs. (19 Nm), then remove
    the drill bit.
  17. Make one final check to verify all components are properly timed, then
    remove all timing pins.
  18. Install the timing chain front cover.
  19. Connect the negative battery cable, start the engine and check for leaks.





    Fig. 5: Rotate the crankshaft clockwise until the timing mark
    on the crankshaft sprocket and keyway align with the main bearing cap split line

    89563pb1.jpg






    Fig. 6: Loosen the timing chain tensioner mounting bolt . . .
    89563pb4.jpg






    Fig. 7: . . . and remove the tensioner from the engine block
    89563pb7.jpg






    Fig. 8: Retract the tensioner plunger and pin the ratchet lever
    with a 1?8
    in. (3.18mm) drill bit inserted in the alignment hole
    89563pb5.jpg






    Fig. 9: Remove the mounting fasteners from both timing guides .
    . .
    89563pb8.jpg






    Fig. 10: . . . and remove the timing guides from the engine
    89563pc1.jpg






    Fig. 11: Remove the camshaft sprocket bolts, using a 7?8 in. (21mm) wrench
    to hold the camshaft
    89563pc2.jpg






    Fig. 12: Remove the timing chain and camshaft sprockets
    89563pc4.jpg






    Fig. 13: Insert the timing pins to verify that the camshafts
    are at TDC
    84193146.gif






    Fig. 14: Make sure that the silver link plates and reference
    marks are all in alignment as shown
    84193145.gif



prev.gif next.gif

Oct 07, 2010 | 1998 Saturn SL

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

1 Answer

What is the position for the timing chain gears.


Timing Chain and Sprockets REMOVAL & INSTALLATION 2.3L and 2.4L Engines The following tools will be required to perform this procedure:
  • Camshaft sprocket timing alignment pins - J 36008 or equivalent
  • Camshaft sprocket wrench - J 39579 or equivalent
  1. Fig. 1: View of the DOHC engine "timed position'' - 2.3L and 2.4L engines 86883175.gif
    Fig. 2: View of the SOHC engine "timed position'' - 2.3L engine 86883176.gif
  2. Remove the timing chain guides. There are usually three.
  3. Raise and safely support the front of the vehicle.
  4. Make sure all of the slack is above the tensioner. Gently pry off timing chain tensioner spring retainer, then remove the spring. NOTE: On the 2.3L engine two styles of tensioners are used. Early production engines will have a spring post and late production ones will not. Both styles are identical in operation and are interchangeable.
  5. Remove the timing chain tensioner shoe retainer.
  6. Make sure all the slack in the timing chain is above the tensioner assembly; remove the chain tensioner shoe. The timing chain must be disengaged from the wear grooves in the tensioner shoe in order to remove the shoe. Slide a suitable small prybar under the timing chain while pulling shoe outward.
  7. If difficulty is encountered while removing chain tensioner shoe, proceed as follows:
    1. Lower the vehicle.
    2. Hold the intake camshaft sprocket with a camshaft sprocket wrench - J 39579 or equivalent holding tool and remove the sprocket bolt and washer.
    3. Remove the washer from the bolt and re-thread the bolt back into the camshaft by hand. The bolt provides a surface to push against.
    4. Remove intake camshaft sprocket using a 3-jaw puller in the 3 relief holes in the sprocket. NOTE: Do NOT try to pry the sprocket off the camshaft or damage to the sprocket or chain housing could occur.
  8. Unfasten the tensioner assembly attaching bolts, then remove the tensioner. CAUTION
    The tensioner piston is spring loaded and could fly out causing personal injury. Use care when removing.
  9. Matchmark the timing chain outer surface for reassembly purposes.
  10. If equipped, remove the chain housing to block stud, which is actually the timing chain tensioner shoe pivot.
  11. Remove the timing chain.
  12. Inspect the parts for wear, then replace if necessary. Some scoring of the timing chain shoe and guides is normal. Clean the old sealant off of the bolt with a wire brush. Clean the threaded hole in the camshaft with a round nylon bristle brush. To install: WARNING
    Failure to following installation procedures can result in severe engine damage.
  13. Install the intake camshaft sprocket onto the camshaft with the marked surface showing. Install the sprocket retaining bolt and washer. Use an adhesive compound 12345493 or equivalent on the bolt. Tighten the bolt to 52 ft. lbs. (70 Nm), while holding the sprocket with tool J-36013, J 39579 or equivalent, if removed.
  14. Install tool J 36800 or equivalent, through hole(s) in the camshaft sprocket(s) into the holes in the timing chain housing. This positions the camshafts for correct timing. Fig. 3: Placing the camshaft sprockets onto the marked surface of the camshaft 91063g30.gif
  15. If the camshafts are out of position and must be rotated more than 1?8 turn in order to install the alignment dowel pins:
    1. The crankshaft must be rotated 90°clockwise off of TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft COUNTERCLOCKWISE back to TDC. NOTE: Do NOT rotate the crankshaft clockwise to TDC, or valve and piston damage could occur. WARNING
      The side of the timing chain that was marked must be facing outward when installed.
  16. For DOHC engines only, install the timing chain over the exhaust camshaft sprocket, around the idler sprocket and around the crankshaft sprocket.
  17. Remove the alignment dowel pin from the intake (DOHC only) camshaft. Using dowel pin remover tool J 39579 or equivalent, rotate the intake (DOHC only) camshaft sprocket counterclockwise enough to slide the timing chain over the intake (DOHC only) camshaft sprocket. Release the camshaft sprocket wrench. The length of chain between the two camshaft sprockets will tighten. If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated. Fig. 4: Place the timing chain over the exhaust camshaft and around the idler sprocket and around the crankshaft sprocketDOHC engines 91063g31.gif
  18. Leave the alignment dowel pins installed.
  19. Raise and safely support the vehicle.
  20. With slack removed from chain between intake camshaft sprocket (camshaft sprocket for SOHC engines) and crankshaft sprocket, the timing marks on the crankshaft and the cylinder block should be aligned. If marks are not aligned, move the chain one tooth forward or rearward, remove the slack and recheck the marks.
  21. If equipped, tighten the chain housing to block stud. The stud is installed under the timing chain. Tighten to 19 ft. lbs. (26 Nm).
  22. For vehicles through 1991, reload timing chain tensioner assembly to its "zero'' position as follows:
    1. Assemble restraint cylinder, spring and nylon plug into plunger. Index slot in restraint cylinder with peg in plunger. While rotating the restraint cylinder clockwise, push the restraint cylinder into the plunger until it bottoms. Keep rotating the restraint cylinder clockwise but allow the spring to push it out of the plunger. The pin in the plunger will lock the restraint in the loaded position.
    2. Install tool J-36589 or equivalent, onto plunger assembly.
    3. Install plunger assembly into tensioner body with the long end toward the crankshaft when installed.
  23. For 1992-98 vehicles, reload timing chain tensioner assembly to its "zero'' position as follows:
    1. Form a keeper from a piece of heavy gauge wire. See the accompanying figure.
    2. Apply slight force on the tensioner blade to compress the plunger.
    3. Insert a small prybar into the reset access hole, then pry the racket pawl away from the ratchet teeth while forcing the plunger completely in the hole.
    4. Install the keeper between the access hole and the blade. Fig. 5: View of reloading the timing chain tensioner assembly to its "zero'' position - 1992-98 vehicles 86883177.gif
  24. Install the tensioner assembly to the chain housing. Recheck the plunger assembly installation. It is correctly installed when the long end is toward the crankshaft.
  25. Install and tighten timing chain tensioner bolts. Tighten to 89 inch lbs. (10 Nm).
  26. Install the tensioner shoe and tensioner shoe retainer. Remove the special tool J-36589, then squeeze the plunger assembly into the tensioner body to unload the plunger assembly.
  27. Lower vehicle enough to reach and remove the alignment dowel pins.
  28. Rotate crankshaft clockwise (normal rotation) two full rotations. Align the crankshaft keyway with the mark on the cylinder block, then reinstall the alignment dowel pins. The pins will slide in easily if the engine is timed correctly. WARNING
    If the engine is not correctly timed, severe engine damage could occur.
  29. Install the timing chain guides and, if equipped, the crankshaft oil slinger.
  30. Install the timing chain front cover. For details, please refer to the procedure located in this section.
  31. Connect the negative battery cable, then start the engine and check for oil leaks.

Oct 07, 2010 | 1998 Buick Skylark

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

1 Answer

What are the timing marks for a 1998 mercury mystisque 4cy....I need to know how to position them


1998 Mercury Mystique 2.0L MFI DOHC 4cyl

e842492.jpg

align the camshafts and the...

20f3fce.gif

Fig. 5: Alignment marks for timing chain installation-left hand side

3da874c.gif

Fig. 6: Alignment marks for timing chain installation-right hand side

Hope thats help.

Feb 02, 2010 | 1998 Mercury Mystique

2 Answers

How to align cams on a 95 ford contour 2.0 dohc?


In order to time this engine you've got to align the cams with the respective markings on the new belt, this also pertains to the crankshaft pulley. If there are no markings on the belt, the camshaft markings will have a demarkation on the head two which each cam must be aligned. From here I cannot tell you where thes marks are but they are usually at 12:00 or 3:00 plus when you get near the alignment point the cams will feel almost like they are freewheeling for about 3/4- 1 inch in either direction.The crankshaft has to be at TDC or topdead center. this is easily accomplised with a 12 inch ruler laid across the front of the pulley with the long side facing up. This way you can center the mounting bolt and the timing mark at the same time, assuring you of exact center alignment. That's about all I can offer. Thank you, Dana. P.S. please do not turn the engine over with the key until you are certain that all three marks are dead on target. You may however turn it over by hand using a socket of the correct size going clockwise on the crankshaft.

Sep 06, 2009 | 1995 Ford Contour

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...