Question about 1988 Ford F 150

1 Answer

Fuel delivery none of the fuel pumps work when hooked to the factory harness. I have replaced the fuel pump relay and still nothing when I bench tested the fuel pumps they are all working

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

Maybe the immobilisor

Posted on Jun 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel off switch on a 2000 dodge intrepid


Fuel off switch ? no such thing ! Which engine does yours have ? Three different ones for your vehicle .2.7 , 3.2 , 3.5
I'm looking at a wiring diagram for the fuel pump circuit of your vehicle , two fuse's a relay , the fuel pump an the PCM -powertrain control module - engine computer ! I'am assuming your vehicle doesn't start an you think there is a fuel delivery problem , why ? Did you hook up a fuel pressure gauge an none was showing on the gauge ? Do you know how to test for B+ voltage at a relay ? An how to test for control by the PCM ? Videos on youtube ! Fuel Pump Electrical Circuits Description and Operation If you can't fix it after watching this your best bet would be to take it to a qualified repair shop !

Aug 14, 2016 | Dodge Cars & Trucks

1 Answer

Fuel delivery problem


If you can use a jumper to run the fuel pump, does it get fuel past the fuel filter? If not I would replace the filter, If that doesn't work , then I would suggest the problem is in your wiring and most likely a loose ground wire or even a fuel tank ground strap. which could be one of it's mounting straps. If none of this helps then re-post with the original problem before you started changing parts... Good Luck

Jul 20, 2014 | 1991 Chevrolet K1500

1 Answer

Toyota Tacoma fuel problem


Check the following:
- Listen to the fuel pump noise under the fuel tank.
- Starter signal.
- EFI relay, under the hood fuse and relay box.
- Fuel pump operation and pressure.
- Regulating valve.
- Circuit Opening Relay (COR) under the dash.
- Check for open in harness and connector between circuit opening relay and fuel pump, and fuel pump and body ground

83744154-13d8-40aa-bba8-aac743062e3f.png
98828e43-1df3-476c-94fa-036164d23c8e.png

2e76aaa2-2dec-411f-a493-b4d0f142f0f8.png
Hope that works. Thank you for visiting Fixya.

Mar 18, 2014 | 1998 Toyota Tacoma

1 Answer

No power after 4000 rpms


This sounds like a fuel pump or fuel filter problem.
The 1988 Jetta has two fuel pumps. The "main" one under the car directly in front of the gas tank on the right hand side. The other fuel pum is in the tank. You can access that fuel pum by removing the round access panel in the trunk towards the back seat.

You'll need a fuel pressure gauge. You can usually borrow one from a large auto parts chain store.

FUEL DELIVERY & SYSTEM PRESSURES
System Pressure
Connect Pressure Gauge (VW 1318) between line from fuel distributor to cold start valve and
test port connection on lower chamber of fuel distributor, using Adapter Fittings (VW 1318/5).
Test port is sealed by a threaded plug. Bridge fuel pump relay with Jumper Switch (US 4480/3).
1.
Disconnect wiring from Differential Pressure Regulator (DPR). Open valve on pressure gauge
(points at cold start valve line when open) and activate fuel pump. System pressure must be 75-
82 psi (5.3-5.8 kg/cm2 ). If pressure reading is low and fuel pump delivery quantity is good,
replace pressure regulator.
2.
If pressure reading is high, disconnect fuel tank return line from DPR. Repeat test. If reading is
correct, check for plugged return line. If reading is incorrect with line open, replace DPR.
3.
Differential Control Pressure
Close valve on pressure gauge. Activate fuel pump with jumper switch. Leave DPR
disconnected. DPR reading should be 2.9-7.0 psi (.2-.5 kg/cm2 ) less than system pressure. If
pressure is incorrect, disconnect lower chamber return line and measure volume.
1.
Close open port to diaphragm pressure regulator. Activate fuel pump with jumper switch. Fuel
volume should be .14-.16 qts. (.13-.15L) for period of one minute. If volume is correct, replace
DPR. If volume is incorrect, replace fuel distributor.
2.
Close valve on pressure gauge. Install Test Harness (1315A/1) between DPR and vehicle
harness. Set multimeter to DCA 200 mA scale. Connect multimeter to test harness. Disconnect
wiring to coolant temperature sensor. Connect 15 k/ohm side of Test Resistor (VW 1490) to
sensor wiring.
3.
Turn on ignition and fuel pump. Differential pressure should be 10-17.5 psi (.7-1.2 kg/cm2 )
less than system pressure. DPR current should be 50-80 mA. If pressure is incorrect and current
is correct, replace DPR.
4.
If both pressure and current readings are incorrect, remove test harness from DPR. Ensure
resistance of DPR is 17.5-21.5 ohms. If reading is incorrect, replace DPR.
5.
If reading is correct, check ground from temperature sensor to cold start valve. If ground is
good, check power supply fuse. If fuse is okay, check terminals on ECU connector. If connector
is okay, replace ECU.
6.
Residual Pressure & Internal Leak Testing
Open valve on pressure gauge. Operate fuel pump for 30 seconds. Pressure can drop to a
minimum of 38 psi (2.7 kg/cm2 ) after 10 minutes. If pressure drops below specification, inspect
fuel pump check valve and all fuel fittings for leakage.
1.
NOTE: Pressure and leak testing does not include checking cold start
valve.
FUEL INJECTION SYSTEM - BOSCH CIS-E -1988 Volkswagen Jetta Page 1 of 3
http://www.ondemand5.com/mric/common/asp/printart.aspx 11/25/2011
If there are no leaks, check airflow sensor plate clearance. If plate clearance is correct, replace
diaphragm pressure regulator and repeat leak test. If pressure drop is not within specification,
replace fuel distributor "O" rings.
2.
Transfer Pump Delivery Volume
Check voltage supply to pumps. Connect Jumper Switch (US 4480/3) in place of fuel pump
relay, on relay panel. Remove fuel filler cap. Disconnect and plug off Black fuel line from
sending unit.
1.
Connect hose to sender port and place in measuring container. Turn on fuel pumps. Minimum
transfer pump delivery volume should be .42 qts. (.4L) in 10 seconds. Reconnect fuel line to
sender.
2.
Main Pump Delivery Volume
Check transfer pump (if equipped) and fuel filter. Disconnect fuel return line and place in
measuring container. Switch on fuel pump with jumper switch. Check fuel pump delivery
volume for 30 second period. Delivery rates are given with voltage reading at pump as volume
will change with different voltages.
1.
Minimum delivery volume for Fox, Quantum and Quantum Syncro models is .71 qts. (.68L) for
30 seconds with reading of 11.4 volts at fuel pump. Minimum delivery volume for other models
is .62 qts. (.59L) with 11.4 volts at fuel pump.
2.
Fuel Distributor
Check sensor plate adjusting lever and fuel distributor control piston for smooth operation.
Disconnect fuel injector lines at fuel injectors.
1.
Remove fuel pump relay and bridge fuel pump circuit. Use Jumper Switch (US 4480/3) in place
of fuel pump relay. When pressure has built up, turn off fuel pump. Move sensor plate from rest
position to end of travel.
2.
Uniform resistance should be felt during entire movement. No resistance should be felt on
quick return to rest position. Connect injector lines. Install fuel pump relay.
3.
Injector Quantity Comparison
Remove fuel pump relay, from relay panel, and install Jumper Switch (US 4480/3) in off
position in place of relay. Attach Fuel Quantity Analyzer (US 4480) to bumper and secure in
place. Remove injectors from cylinder head with fuel lines attached. Check and replace fuel
injector "O" rings as necessary.
1.
Check tightness of injector insert (2-piece inserts). If inserts are loose, remove and clean
threads. Use sealing compound when installing upper insert. Replace sealing washer that goes
against cylinder head below lower portion of insert. Lubricate injector "O" rings with gasoline
and install injectors, with fuel lines connected, into fuel quantity analyzer tubes.
2.
Ensure lines are not kinked or bent. Loosen fittings to align fuel lines and retighten. Remove
rubber boot from airflow sensor housing above sensor plate. Turn and lift setting screw and
adjusting slide of Sensor Plate Adjustable Holder (VW 1348/1) into upper position. This
simulates full throttle operation. See Fig. 11 .
3.
FUEL INJECTION SYSTEM - BOSCH CIS-E -1988 Volkswagen Jetta Page 2 of 3
http://www.ondemand5.com/mric/common/asp/printart.aspx 11/25/2011
Fig. 11: Sensor Plate Adjustable Holder (VW 1348/1)
Courtesy of AUDI OF AMERICA, INC.
Place sensor plate adjustable holder on airflow sensor housing with holder centered over plate.
Pointer on edge of holder base must point toward center of fuel distributor. Push adjusting slide
of holder down onto stop.
4.
Turn adjusting screw clockwise until magnetic end touches sensor plate retaining bolt. Activate
fuel pump with jumper switch. Turn adjusting screw of holder counterclockwise until any one
injector starts to deliver fuel. Turn off jumper switch and empty fuel quantity analyzer after
taking sample.
5.
Idle injection quantity is measured first. Lifting adjusting slide of holder to first stop simulates
idle position of sensor plate. Activate fuel pump until fuel level reaches 20 ml on scale of any
tube.
6.
Check that all injectors have identical spray patterns that are even and cone-shaped. If not, raise
sensor plate up quickly to full lift position and release. Repeat idle quantity test. Compare
amounts of fuel delivered by all injectors with analyzer held level. Maximum difference in
delivery quantity between injectors is 3.0 ml of fuel.
7.
If fuel delivery quantity differs between high and low levels by more than 3.0 ml, interchange
injectors and repeat test. If difference of delivery quantity changes with injectors, replace
injectors. If difference of delivery quantity does not change with movement of injectors, either
fuel lines are pinched or fuel distributor is defective.
8.
Measure full throttle injection quantity. Empty analyzer into fuel tank and reinstall injectors in
analyzer. Lift adjusting slide of holder to last stop to simulate full throttle position of sensor
plate. Activate fuel pump with jumper switch until fuel level reaches 80 ml on scale of any tube
of analyzer.
9.
Check that all injectors have identical spray patterns that are even and cone-shaped. If not, raise
sensor plate up quickly to full lift position and release. Repeat full throttle quantity test.
Compare amounts of fuel delivered by all injectors with analyzer held level. Maximum
difference in delivery quantity between injectors is 8.0 ml of fuel.
10.
If fuel delivery quantity differs between high and low levels by more than 8.0 ml, interchange
injectors and repeat test. If difference of delivery quantity changes with injectors, replace
injectors. If difference of delivery quantity does not change with movement of injectors, either
fuel lines are pinched or fuel distributor is defective.
11.
Check fuel injectors for leakage immediately after delivery quantity test is complete. Set sensor
plate in rest position. Activate fuel pump with jumper switch for 2 minutes. Injectors should not
drip. Replace injectors that drip.
See image. Fuel filter is probably located on the frame between the engine and fuel tank.
8_24_2012_11_36_10_pm.jpg8_24_2012_11_36_30_pm.jpg

Jul 03, 2012 | 1988 Volkswagen Jetta

1 Answer

1997 Suburban, cranks, won't start. Removed fuel pump and it runs when attached to battery on bench. Power at all fuses, no power on grey wire at 4 prong connector above rear axle. Is there a fuel pump cut...


The oil pressure gauge on the engine runs the fuel pump until the engine receives full oil PSI and shuts off. Upon that time the relay takes over for the fuel pump

Jan 25, 2010 | 1997 Chevrolet Suburban

1 Answer

No power at ineartia switch


try running power from relay to the inertia switch through a jumper wire and see if pump works. you might have a pinched or broken wire in the factory harness.

Jun 10, 2009 | 1999 Nissan Quest

3 Answers

1999 oldsmobile silhouette van won't start. no power to fuel pump


I have a silhouette and it had the same problem
Follow the fuel pump wiring harness to where it plugs into the floor of the van--pull the connectors apart--they will probably be corroded, and you will possibly have to change both wiring harnesses or connectors.

May 25, 2009 | 1999 Oldsmobile Silhouette

1 Answer

My 1997 Chevy 4 dr 4x4 has fuel delivery problems.


try replacing your relay first not that expensive and easy to change also some models have a red jumper wire on the relay plug that sends power directly to pump

Mar 26, 2009 | 1997 Chevrolet Blazer

1 Answer

Starts then quits


Was there fuel pressure before you changed everything? It could also be the pressure regulator sticking or bad. When you crank it over and let off the key you should hear the fuel pump run for a couple seconds and then shut off. If it is doing that then I would be looking to see if you have likes hooked up wrong at the back of the engine or try replacing the pressure regulator.

Dec 23, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...