Question about 2004 Dodge Durango

1 Answer

Where is the valet button override button in 2004 dodge durango

Security system will not allow the vehicle to crank and have been told to press valet button to reset security system?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

The
valet/overide button, found under the
dash area

Posted on Mar 25, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cartersintn
  • 62 Answers

SOURCE: security system engaged

Try to lock and unlock the drivers door manually with the key

Posted on Sep 09, 2008

66 chrgr
  • 1011 Answers

SOURCE: Crank sensor location 1999 dodge durango

the crank sensor is located passenger side back of the engine were the trans and engine come together .there are 2 - 13mm.bolts that bolt to top of the engine.

Posted on Feb 22, 2009

carsandcomps
  • 722 Answers

SOURCE: 2005 dodge durango key fob

Hello and thank you for choosing fixya.com. I would suggest taking your vehicle to a local auto parts store and request to have a diagnosis done. (while auto stores vary, this is usually a free service and only takes a couple minutes to complete) to see if any codes are brought up. If so, the representative can tell you what the codes mean, and what needs replaced or repaired. Let them know of the situation. Even if no codes show up, ask them to clear the codes. If this does not work, do the following. 1: make sure that the batter in your key fob is inserted correctly, and that it is the correct size and type. 2. Disconnect the + Positive cable on your battery. This will reset your the vehicles computer. Maybe this will allow the vechile to code up with the fob. If not, I would take it to dealership, or backto an auto part store for further assitance.

I thank greatly for choosing fixya.com. I hope this information is useful to you and helps you get your fob working again. Let me know if you need further assistance, or have any questions or comments. Feel free to rate this information at your earliest convenience.

Posted on Apr 01, 2009

motor1258
  • 6674 Answers

SOURCE: how to reset security system on 2001 dodge durango

Try using key in doors to unlock them.

Posted on Jun 02, 2009

  • 412 Answers

SOURCE: I have a 1999 Dodge durango and the alarm is stuck

TRY LOCKING ALL DOORS,THEN UNLOCK PASSENGER SIDE FRONT DOOR WITH KEY..THIS SHOULD DISARM SYSTEM..IF NOT,REMOVE TRIM PLATES AT LF DOOR AND LOOK FOR ANY BROKEN WIRES UNDER TRIM AND CARPET..I HOPE THIS HELPS

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to find out where the valet/override button is located on my car....trying to program a new keyless remote


1. Insert key into the ignition and turn it to the On or ACC position, turn off radio. (do not start the vehicle)

2.Press and hold DISP button on radio until settings is displayed.

3. Press Seek until FOB PROG is displayed .

4. Press Prev or Next and BEGIN will be displayed

5. Press DISP and programming will begin when PUSH FOB is displayed. Press and hold Lock and Unlock together until vehicle chimes. This will signal successful programming. May have to hold buttons up to 20 seconds. Hold Lock and Unlock on additional remote until vehicle chimes again.

6. Exit programming mode. Scroll to Exit and press DISP to exit programming.

If you don't have the original radio, it can be done with a scanner.

Mar 19, 2016 | 2004 Chevrolet Chevrolet Impala

1 Answer

How can a security system be reprogramed in a 2004 Durango with a 5.7 hemi


Try this Instructions
    • 1Press the "Unlock" button on the remote keyless entry device.
    • 2 Insert the key into the ignition. Turn the ignition switch to "ON" without starting the engine.
    • Sponsored Links
    • 3 Press and hold the valet/override button below the steering column within five seconds of turning the ignition on.
    • 4 Release the valet/override button when the security light on the instrument panel stops blinking. The alarm is reset and disabled.


Read more

Jan 11, 2015 | 2004 Dodge Durango

1 Answer

My security light want go off on my 2006 dodge charger


Are you using a valet key? It requires the factory key that has a chip in it that the vehicle security system can identify. Anything else will not defeat the security system. And sometimes, the security system must be reset via the dealer's scan tool and access codes only they have. Sorry I couldn't be more help

Dec 12, 2014 | 2006 Dodge Charger

1 Answer

Car starter in valet mode


  1. 1 Insert the key into the ignition.
  2. 2 Turn the ignition switch to "ON." Do not start the engine.
  3. 3 Press and hold the valet/override button within five seconds of turning the ignition on. The valet button is located beneath the steering column.
  4. 4 Release the valet/override button after the security indicator light turns off.
  5. 5 Turn the ignition switch off.

Dec 07, 2013 | Dodge Cars & Trucks

1 Answer

2001 dodge durango /tail light troubleshooting


Open the rear door, locate the two screws next to the tail light. They will be philips head. Take them out, pop off tail light, unhook light harness. Reinstall is opposite of removal.

Sep 01, 2012 | 2001 Dodge Durango

1 Answer

I have a 2000 dodge intrepid. The alarm never worked on it. We bought it used and all of a sudden when we go to unlock the door it turns on. Now the car won't start. I've looked online for answers and...


The 2000 Dodge Intrepid is equipped with an alarm system that is triggered when unauthorized entry is attempted. In some situations, such as having the Intrepid valet parked or when it is being serviced by a mechanic, the alarm system needs to be disarmed so it doesn't go off. Disarming the alarm will prevent it from being activated until it is armed again.
Difficulty: Moderate Instructions

  1. 1 Insert the key into the ignition.
  2. 2 Turn the ignition switch to "ON." Do not start the engine.
  3. 3 Press and hold the valet/override button within five seconds of turning the ignition on. The valet button is located beneath the steering column.
  4. 4 Release the valet/override button after the security indicator light turns off.
  5. 5 Turn the ignition switch off.


have to do it in this order

Dec 10, 2010 | 2000 Dodge Intrepid

1 Answer

I have a viper alarm on my car that wont shut off nor i cant start the car..and i have tried the button under my dash, how Can i shut it off??


was it a professional or shade tree install? the following is off vipers website:
disarming without a remote control
This feature allows you to disarm the security system without the
Remote Control should it be lost, damaged, or disabled. In order to
disarm the system without a remote remote control, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON position.
Press the Valet button the
preset number of times (one to
five times) within 15 seconds. After five seconds the system will
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
if that doesn't work try this other

valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the Remote Control, but
all convenience functions (door locks, trunk release, etc.) will
continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.

May 08, 2010 | 1994 Honda Civic

1 Answer

REPROGRAM THE FOB DODGE DURANGO 2004


ATTENTION: You MUST HAVE one working remote to add one more to the system.
If you do not have one working remote right now then these instructions will not work.
You will have to have a Locksmith or dealership use a computer to program the first
remote for you.



1. Press LOCK button 5 times at 2 second intervals to resynchronize remote.
2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can
go without cranking engine). Wait for ignition chimes to stop.

3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.

4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then
press the PANIC button ( on the programmed remote ) for 1 second and release both
buttons. A chime will sound to indicate that the remote programming mode has been
entered ( allow 3 seconds for chime to sound ).

5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons
simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release
the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on
each new remote you wish to program at this time. Locks will cylce afer each additional
remote is programmed.

6. Turn the ignition OFF and remove key.
7. Test Remotes.

Thanks for using FixYa - a Very Helpful rating is appreciated for answering your FREE question.

Jul 09, 2009 | 2004 Dodge Durango

2 Answers

Car alarm goeoss car will not start


<Have heard that putting key into ignition in 'on' position and waiting sixty seconds for alarm to go off, then turning key off and back on will disable alarm. Haven't tried it yet.>

rweh is correct! Thank you! It worked for me!

Nov 18, 2008 | 2001 Hyundai Elantra

Not finding what you are looking for?
2004 Dodge Durango Logo

616 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...