Question about Cars & Trucks
I f the light is blinking leave car in run position wait for it to stop takes mine around ten minutes when it stops turn key all the way off then should start right up hope this helps not sure its the same problem I have.
Posted on Jul 03, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
at the base of the steering column there a orange and white wires these two wires come from the ing switch, you will see the connector that they go to disconnect that take a ohm meter, take the leads one lead to one wire the other lead to the other there should be res, if there is not, try a different setting . take your ing key on the the key you will see a chip take two leads from your meter and either side of the chip place the leads you will see a res reading, you should see the same at the orange and white wires . if you do not replace the ing switch the switch will come with these wires. replacing the switch takes a couple specail tools good luck and let me know how it gose
Posted on Dec 22, 2008
SOURCE: WARNING LIGHTS MESSAGE ( ! )
sounds like your tire pressure sensors are iffy. just my input...any other sensors come on? like your tire pressure ones? if not, try and add a tiny bit of air in each tire until its dead on the recommended pressure, then check to see if the light has went off...hope im right on this one lol
Posted on Feb 18, 2009
never heard of this happening before ,sounds more like the code reader behind the steering lock is playing up.If it is then its dealer only,have a funny feeling this could be an expensive repair.Sorry i couldnt be much more help but this fancy electronic stuff is designed to stop general mechanics like myself from doing repairs.
Posted on Mar 16, 2009
It is your locks. I would just disconnect them and lock the car manually. Its a common problem on most GM cars cause water got in an rusted the auto lock motor cause them to send the wrong signal to the computer.
Posted on May 13, 2009
Try this first, it takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself. Good luck and hope this helps, keep me posted, be glad to help
Posted on Jun 22, 2009
Tips for a great answer:
Sep 24, 2016 | 2008 Chevrolet Chevrolet TrailBlazer LT
Jul 26, 2016 | 2003 Chevrolet TrailBlazer
Dec 05, 2015 | Cars & Trucks
The ignition lock cylinder case, including the Passlock?"¢ sensor
The ignition switch
The body control module (BCM)
The security indicator on the instrument cluster
The powertrain control module (PCM)
Ignition Lock Cylinder Case, Including the Passlock?"¢ Sensor
The ignition lock cylinder fits inside the ignition lock cylinder case and operates the ignition switch when turned by a key with the proper mechanical cut. When the ignition key is used to turn the ignition lock cylinder to crank, start, a magnet on the lock cylinder passes close to the Passlock?"¢ sensor within the ignition lock cylinder case. The magnet activates the security hall effect sensor in the Passlock?"¢ sensor which completes a circuit from the security sensor signal circuit through a resistor to the security sensor low reference circuit. The resistance value will vary from vehicle to vehicle.
If a magnet from outside of the ignition lock cylinder case is used to attempt to steal the vehicle, the tamper hall effect sensor will be activated. This completes a circuit from the security sensor signal circuit through a tamper resistor to the security sensor low reference circuit bypassing the security resistor. If the ignition switch is forced to rotate without the correct key, or if the ignition lock cylinder is removed by force, the Passlock?"¢ sensor will be damaged and will not operate.
Feb 22, 2015 | 2006 Chevrolet Trailblazer
Aug 21, 2012 | 2000 GMC Jimmy
Jul 11, 2011 | 2006 Chevrolet Trailblazer
Feb 09, 2011 | 1999 Oldsmobile Intrigue
Feb 02, 2011 | Chevrolet Chevy Cars & Trucks
Nov 20, 2010 | 2002 Chevrolet TrailBlazer
May 09, 2009 | 2005 Saturn ION
37 people viewed this question
Usually answered in minutes!